Fluke 6109A Handleiding
Fluke
Temperatuurregelaar
6109A
Lees hieronder de 📖 handleiding in het Nederlandse voor Fluke 6109A (4 pagina's) in de categorie Temperatuurregelaar. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
PN 4924861
September 2017, Rev. 1, 3/21
©2017-2021 Fluke Corporation. All rights reserved.
All product names are trademarks of their respective companies.
Fluke Corporation
P.O. Box 9090
Everett, WA 98206-9090
U.S.A.
Fluke Europe B.V.
P.O. Box 1186
5602 BD Eindhoven
The Netherlands
1
Calibration Bath
Safety Information
Introduction
This document supplies safety information for the Calibration Bath (the Product).
Safety Information
A Warning identifies hazardous conditions and actions that could cause bodily harm or death.
A Caution identifies conditions and actions that could damage the Product, the equipment under test, or cause
permanent loss of data.
Symbols
The symbols used in the manuals and on the Product are shown below.
Symbols
Symbol Description
X Hazardous voltage. Risk of electric shock.
W Risk of Danger. Important information. See Manual.
» Consult user documentation.



XW Warning
To prevent possible electrical shock, fire, or personal injury:
• Read all safety information before you use the Product.
• Carefully read all instructions.
• Do not alter the Product and use only as specified, or the protection supplied by
the Product can be compromised.
Calibration Bath
Safety Information
2
• Do not use the Product if it is altered or damaged.
• Do not use the Product around explosive gas, vapor, or in damp or wet
environments.
• Use this Product indoors only.
• Do not use an extension cord or adapter plug.
• Replace the mains power cord if the insulation is damaged or if the insulation
shows signs of wear.
• Make sure the ground conductor in the mains power cord is connected to a
protective earth ground. Disruption of the protective earth could put voltage on the
chassis that could cause death.
• Do not put the Product where access to the mains power cord is blocked.
• Make sure that the space around the Product meets minimum requirements.
• Read the bath fluid safety data sheet (SDS) and take necessary precautions. Some
fluids are corrosive, toxic, or irritate the skin, eyes, nose, and respiratory organs.
• Use a ventilation system to remove vapor.
• Do not use fluids that are corrosive to stainless steel.
• Always use the provided access cover or other suitable metallic access cover if
the selected bath fluid is flammable. An exposed heater element, due to low-liquid
level or other external ignition sources, could lead to spread of fire from the bath
access port. The access cover limits air ingress into the bath headspace and
prevents ignition and helps to quickly extinguish any fire. The access cover may
be drilled to permit temperature probe insertion.
• Use only specified replacement parts.
• Have an approved technician repair the Product.
• Do not operate the Product with covers removed or the case open. Hazardous
voltage exposure is possible.
Provide Ventilation
Harmful substances such as benzene and formaldehyde can be produced above a certain temperature when
heating silicone bath fluids. Consult the safety data sheet of the specific bath fluid for the temperatures at which the
fluid begins to degrade and the byproducts that may be emitted.
Bath fluid vapors present a fire hazard, especially when the bath fluid is operated above its flash point. Bath fluid
vapors tend to condense onto surrounding surfaces. This can contaminate materials and inhibit laboratory
cleanliness. If enough condensation accumulates on the floor, the floor becomes slippery and creates a safety
hazard.
For proper fume extraction Fluke Calibration recommends to use at least a ventilation duct of 75 mm (3 in) or more
in diameter with a flow rate of at least 1.4 cubic meters per minute (50 cfm). Place the inlet of the ventilation duct
near the top of the tank.
Calibration Bath
Safety Information
3
Clean Up Spills
Fluid spilled on the floor is a safety hazard. To avoid accidents, follow these precautions and instructions.
WCaution
• Be careful when you fill and operate the Product to avoid drips and spills.
• Keep cleanup materials on hand.
• If a spill occurs, close the area to traffic until the spill is cleaned up.
• Use paper towels or other absorbent material to wipe up spilled fluid.
• Dispose of used cleanup materials properly.
Fluids and solvents may require additional safety precautions. Refer to the material’s safety data sheet (SDS). Bath
fluid residue can be removed with a suitable mild solvent such as Steris SPOR-KLENZ or Dow Corning OS-2 for
silicone.
Product specificaties
| Merk: | Fluke |
| Categorie: | Temperatuurregelaar |
| Model: | 6109A |
Heb je hulp nodig?
Als je hulp nodig hebt met Fluke 6109A stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Temperatuurregelaar Fluke
8 Juli 2024
8 Augustus 2023
8 Augustus 2023
26 Juli 2023
4 Mei 2023
3 Mei 2023
21 April 2023
18 April 2023
16 April 2023
31 Maart 2023
Handleiding Temperatuurregelaar
- Temperatuurregelaar Panasonic
- Temperatuurregelaar AEG
- Temperatuurregelaar Honeywell
- Temperatuurregelaar ACV
- Temperatuurregelaar Astralpool
- Temperatuurregelaar Berker
- Temperatuurregelaar Bulex
- Temperatuurregelaar Davis
- Temperatuurregelaar Dimplex
- Temperatuurregelaar Hager
- Temperatuurregelaar Kathrein
- Temperatuurregelaar Techno Line
- Temperatuurregelaar Technoline
- Temperatuurregelaar Ventus
- Temperatuurregelaar Voltcraft
- Temperatuurregelaar Wachendorff
- Temperatuurregelaar Ygnis
- Temperatuurregelaar Jung
- Temperatuurregelaar Opticlimate
- Temperatuurregelaar Cocraft
- Temperatuurregelaar IFM
- Temperatuurregelaar Inkbird
- Temperatuurregelaar Carel
- Temperatuurregelaar Ziehl
- Temperatuurregelaar SRS
- Temperatuurregelaar Emko
- Temperatuurregelaar Jumo
Nieuwste handleidingen voor Temperatuurregelaar
5 December 2024
5 December 2024
2 December 2024
30 November 2024
30 November 2024
30 November 2024
18 November 2024
18 November 2024
18 November 2024
18 November 2024