Flir PathFindIR II Handleiding

Flir Niet gecategoriseerd PathFindIR II

Lees hieronder de 📖 handleiding in het Nederlandse voor Flir PathFindIR II (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 48 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
PathFindIR II
QuickStart Guide
Ready
Set
Go...
FLIR document number: 421-0053-00-QS, Rev. 100
Quick Start Guide
Installation of the PathFindIR II is quick and easy. Just mount the camera and
ECU, connect to a 12v power source and a video monitor and you’re done.
For the complete user manual and install video please go to our website at the
following link: http://www.ir.com/pf2docs
Before you begin, make sure you’ve got all
of the parts you’ll need. Your PathFindIR II kit
should include the following items:
(along with 4 screws for mounting the camera)
If you purchased the optional
Installation Kit, you will also have:
First, you need to select an acceptable mounting location for the camera head.
1. 2.
3.
PathFindIR Camera Video Monitor
PathFindIR To ECU Cable
PathFindIR
Mounting Bracket
ECU Bracket
(with ECU Installed)
Power/Video Cable
ECU
• Mount the camera in the front of the car behind
the grille, but make sure it has no obstructions
in its view.
• Don’t mount the camera inside the passenger
compartment, because it can’t see through glass.
• To get the best performance out of the camera
and its onboard pedestrian and animal detection
algorithms, you need to make sure the camera
is mounted according to factory specications
(see user guide for details).
• The camera should be mounted between 19 and 31
inches high, with the optimal height above the ground
being 25 and a half inches high (65cm ±15cm). Also
keep in mind that if you can mount the camera higher,
you’ll cut down the chances of the camera getting
damaged by rocks or other road debris.
• Make sure that the camera won’t be exposed to fast
temperature changes, so keep it as far from the
engine as possible.
25.5”+_ 6”
(65cm +_ 15cm)
PathFindIR II
Camera
Display (inside passenger compartment)
ECU (inside passenger compartment
FLIR document number: 421-0053-00-QS, Rev. 100
Mount the camera head with the four M5 screws
in the camera kit. You can either fashion your own
mounting bracket, or use the bracket included in
the optional Installation kit (shown below).
The ECU is not weatherproof, so it needs to
be mounted inside the passenger compartment
or in the truck to protect it from moisture. You
can either mount it yourself, or use the bracket
that comes in the optional Installation kit.
Route the ECU cable from the camera head to the
ECU in its mounted location. Align the connectors
and seat them rmly together. The connector is
designed so it can only be attached one way.
Connect the video output cable to the monitor
of your choosing. It is recommended that this
cable be kept as short as possible.
4. 5.
6.
7.
• Connect the power cable to an appropriate, fused
12 volt power supply and connect the other end
to the ECU in the port marked with the symbol.
The ECU should be grounded to give the best
video signal.
NOTE: IT IS VERY IMPORTANT TO CONNECT THE
POWER TO THE ECU TO THE INPUT MARKED
WITH THE SYMBOL – OTHERWISE YOU MAY
DAMAGE THE ECU!
• Once the camera is installed and operating,
use the image on the display screen to verify
that the camera head is aligned properly.
• In order to get the best Pedestrian and
Animal Detection from the unit it needs to
be precisely aligned;
• Align the camera so that the center of the
image is aligned with the car + or - 2° to the
left or right.
• Also make sure the center of the image is level
with the horizon + or - 2°.
• Finally, make sure the camera isn’t tilted left or
right compared to a at road surface.
• An example of a correct installation is shown
below, with example red alignment lines shown:
That’s it! Congratulations
now go enjoy your PathFindIR II!
FLIR document number: 421-0053-00-QS, Rev. 100

Product specificaties

Merk: Flir
Categorie: Niet gecategoriseerd
Model: PathFindIR II

Heb je hulp nodig?

Als je hulp nodig hebt met Flir PathFindIR II stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Flir

Flir

Flir Boson+ Handleiding

10 Juni 2024
Flir

Flir Hadron 640R Handleiding

10 Juni 2024
Flir

Flir VS290 Handleiding

6 December 2023
Flir

Flir Chameleon3 Handleiding

16 November 2023
Flir

Flir Firefly S Handleiding

16 November 2023
Flir

Flir Grasshopper3 Handleiding

16 November 2023
Flir

Flir Grasshopper2 Handleiding

16 November 2023
Flir

Flir PTU-SDK Handleiding

16 November 2023
Flir

Flir Zebra2 Handleiding

16 November 2023
Flir

Flir VS80 Handleiding

15 November 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Kolcraft

Kolcraft MLB Chicago Cubs Handleiding

26 November 2024
Kolcraft

Kolcraft MLB New York Yankees Handleiding

26 November 2024
Kolcraft

Kolcraft MLB San Francisco Giants Handleiding

26 November 2024
Kolcraft

Kolcraft MLB St. Louis Cardinals Handleiding

26 November 2024
Nedis

Nedis POCO106 Handleiding

26 November 2024
Nedis

Nedis BTSM1GY Handleiding

26 November 2024
Turbosound

Turbosound TPOLEAJ-01 Handleiding

26 November 2024
Turbosound

Turbosound TSTAND-01 Handleiding

26 November 2024
IFM

IFM TAD981 Handleiding

26 November 2024
IFM

IFM TAD961 Handleiding

26 November 2024