First Alert CO410 Handleiding

First Alert Niet gecategoriseerd CO410

Lees hieronder de 📖 handleiding in het Nederlandse voor First Alert CO410 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 30 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6

USER’S MANUAL

BATTERY OPERATED CARBON MONOXIDE ALARM

WITH DIGITAL DISPLAY AND SILENCE FEATURE

Model CO410

Printed in Mexico

M08-0157-003 P07/06

IMPORTANT!

PLEASE READ CAREFULLY AND SAVE.

This user’s manual contains important information about your Carbon

Monoxide (CO) Alarm’s operation. If you are installing this CO Alarm for use

by others, you must leave this manual—or a copy of it—with the end user.

TABLE OF CONTENTS

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1-2

Basic Safe nty I formation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

How Your CO Alarm Works . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

U end rstanding Your CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Using the Remote Control Test/Silence Feature . . . . . . . . . . . . . . . . . . . .2

Using the Peak CO Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-3

Where to Install CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Where CO Alarms Should NOT Be Installed . . . . . . . . . . . . . . . . . . . . . .2

How to Install Your CO Alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

If Your CO Alarm Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

If the Alarm Signal Sounds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Using the Silence Feature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Testing and Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

We lek y Testing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Regular Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

What You Need To Know About CO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-5

What is CO? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Symptoms of CO Poisoning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Finding the Source of CO After an Alarm . . . . . . . . . . . . . . . . . . . . . . . . .4

How Can I Protect My Family? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Potential Sources of CO in the Home . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Underwriters Laboratories Inc. UL2034 . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

General Limitations Of CO Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Tr oubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

BRK Brands, Inc., 3901 Liberty Street Road, Aurora, IL 60504-8122

Consumer Affairs: (800) 323-9005

www.brkelectronics.com

•

www.firstalert.com

INTRODUCTION

BASIC SAFETY INFORMATION

• Dangers, Warnings, and Cautions alert you to important operating

instructions or to potentially hazardous situations. Pay special

attention to these items.

• THIS IS NOT A SMOKE ALARM! This CO Alarm is designed to detect

carbon monoxide from ANY source of combustion. It is NOT designed

to detect smoke, fire, or any other gas.

• This CO Alarm is approved for use in single-family residences.

It is NOT designed for marine use.

• This CO Alarm will only indicate the presence of carbon monoxide gas

at the sensor. Carbon monoxide gas may be present in other areas.

• The Silence Feature is for your convenience only and will not correct

a CO problem. Always check your home for a potential problem after

any alarm. Failure to do so can result in injury or death.

• NEVER ignore your Carbon Monoxide Alarm if it alarms. Refer to

“If Your CO Alarm Sounds” for more information. Failure to do so can

result in injury or death.

• Test the CO Alarm once a week. If the CO Alarm ever fails to test

correctly, have it replaced immediately! If the CO Alarm is not working

properly, it cannot alert you to a problem.

• This product is intended for use in ordinary indoor locations of family

living units. It is not designed to measure CO levels in compliance

with Occupational Safety and Health Administration (OSHA) commer-

cial or industrial standards. Individuals with medical conditions that

may make them more sensitive to carbon monoxide may consider

using warning devices which provide audible and visual signals for

carbon monoxide concentrations under 30 ppm. For additional infor-

mation on carbon monoxide and your medical condition contact your

physician.

HOW YOUR CO ALARM WORKS

GENERAL INFORMATION

• This Co Alarm does not operate without working batteries. Removing

the b or fatteries, ailure to replace them at the end of their service

l e, removes your protection.if

• High temperatures, low temperatures, high humidity, impact or

dropping can adversely affect LCD displays.

A CO Alarm measures the CO levels in the air. It will alarm if CO levels rise

quickl he heat exchanger on your furnace breaks, for example), or if CO y (if t

is consistently present (a slow CO leak on a fuel-burning appliance).

This carbon monoxide alarm features a permanently installed sensor, three

colored indicator lights, and an 85 dB alarm horn. It also has a silence feature

to temporarily quiet the alarm horn.

THE PARTS OF YOUR CO ALARM

1 Open door here

2 Test/Silence Button

3 POWER/ALARM Light (RED)

4 Battery Compartment

5 (Behind Cover) Alarm Horn: 85dB

audible alarm for test, alarm, and

unit malfunction warning.

6 Peak Level Button

7 Digital Display

INSTALLATION

WHERE TO INSTALL CO ALARMS

The National Fire Protection Association (NFPA) recommends that a CO Alarm

should be centrally located outside of each separate sleeping area in the

immediate vicinity of the bedrooms. For added protection, install additional CO

Alarms in each separate bedroom, and on every level of your home.

If your bedroom hallway is longer than 40 feet (12 meters), install a CO Alarm at

BOTH ends of the hallway.

In a Single-level Home:

• Install at least one CO Alarm near or within each separate sleeping area.

• For added protection, install an additional CO Alarm at least 20 feet

(6 meters) away from the furnace or fuel burning heat source.

In a Multi-level Home:

• Install at least one CO Alarm near or within each separate sleeping area.

• For added protection, install at least one CO Alarm on each level of the

home. If you have a basement, install that CO Alarm at the top of the base-

ment stairs.

• For added protection, install an additional CO Alarm at least 20 feet

(6 meters) away from the furnace or fuel burning heat source.

In a Mobile Home:

• Install CO Alarms on inside walls ONLY. Uninsulated outside walls and roofs

of mobile homes often transfer heat and cold from outdoors.

WHERE CO ALARMS SHOULD NOT BE

INSTALLED

DO NOT locate this CO Alarm:

• In a location where it could be easily triggered when using your remote

to operate your TV, VCR, etc.

• In garages, kitchens, furnace rooms, or in any extremely dusty, dirty or

greasy areas.

• Closer than 20 feet (6 meters) from a furnace or other fuel burning heat

source, or fuel burning appliances like a water heater.

• Within 5 feet (1.5 meters) of any cooking appliance.

• In extremely humid areas. This alarm should be at least 10 feet (3 meters)

from a bath or shower, sauna, humidifier, vaporizer, dishwasher, laundry

room, utility room or other source of high humidity.

• In areas where temperature is colder than 40˚ F (4˚ C) or hotter than 100˚ F

(38˚ C). These areas include unconditioned crawl spaces, unfinished attics,

uninsulated or poorly insulated ceilings, porches, and garages.

• In turbulent air, like near ceiling fans, heat vents, air conditioners, fresh air

returns, or open windows. Blowing air may prevent CO from reaching the

sensors.

• In direct sunlight.

• This CO Alarm is designed for use inside a single-family home or

apartment. It is not meant to be used in common lobbies, hallways,

or basements of multi-family buildings unless working CO Alarms

are also installed in each family living unit. CO Alarms in common

areas may not be heard from inside individual family living units.

• This CO Alarm alone is not a suitable substitute for complete

detection systems in places which house many people, like hotels

or dormitories, unless a CO Alarm is also placed in each unit.

• DO NOT use this CO Alarm in warehouses, industrial or commercial

buildings, special-purpose non-residential buildings, RVs, boats,

or airplanes. This CO Alarm is specifically designed for residential

use, and may not provide adequate protection in non-residential

applications.

CO ALARM

Sensor has detected enough CO to trigger an alarm. Light flashes rapidly

and horn sounds loudly (repeating

4 beeps, pause)

. See “If Your CO Alarm

Sounds” for details. During an alarm, move everyone to a source of fresh

air. DO NOT move the CO Alarm!

DIGITAL DISPLAY:

“CO” alternating with

the ppm number, a full level, and “EVACUATE”.

DURING TESTING

Light flashes Red in sync with the horn pattern

(4 beeps, pause, 4 beeps)

simulating a CO Alarm condition.

DIGITAL DISPLAY: During the

simulated CO alarm, “CO” is

displayed along with a full alarm

level. Several ppm CO levels are

also displayed and the alarm level

is shown increasing.

LOW BATTERY WARNING

The light continues to flash (RED) and the horn also “chirps” once every

minute. This warning should last for up to 30 days, but you should replace

the batteries as soon as possible.

DIGITAL DISPLAY: Battery icon will show an empty icon.

CO ALARM REQUIRES SERVICE (MALFUNCTION SIGNAL)

The light flashes (RED) and the horn sounds 3 quick “chirps” every minute.

CO Alarm needs to be replaced.

DIGITAL DISPLAY: “ERROR” is displayed.

GARAGE



SUGGESTED AREAS FOR INSTALLING ADDITIONAL CO ALARMS

BEDROOM

HALL

LIVING ROOM

KITCHEN

BASEMENT

BEDROOM

REQUIRED TO MEET NFPA RECOMMENDATIONS

USING THE PEAK CO MEMORY

The CO Memory Feature lets you check the highest level of CO recorded

during an alarm.

To check CO Memory:

1. Press the Peak Level Button until the peak CO

level is displayed.

To clear CO Memory:

1. While checking CO memory, press or hold the

Peak Level Button until “CLEAR” is displayed.

2. Press or hold the Peak Level Button until the CO

Memory is cleared.

NOTE: The highest CO level will be saved until you clear it. DO NOT clear the

CO Memory reading if you plan to call someone to investigate a CO problem!

Clear the CO Memory reading only after the investigator has checked your

home.

USING THE REMOTE CONTROL TEST/SILENCE FEATURE

Using the VOLUME or CHANNEL buttons on most remote controls, you can

test or silence this CO Alarm from up to 12 feet (3.6 meters) away.

To Test or Silence the Alarm:

1. Make sure you have a clear path between you and the

Alarm, free of any obstructions.

2. Point the remote at the front of the Alarm.

3. Press the VOLUME or CHANNEL button for at least

5 seconds.

If the Alarm does not respond to your remote control:

• You may be standing too far away.

• Your remote may not be compatible.

• You did not hold the button on your remote for at least

5 seconds.

• The remote Silence Feature only works once in an alarm situation. Using

the Test/Silence button on the CO Alarm will still silence the unit. The

remote Silence Feature will return when the unit clears itself.

UNDERSTANDING YOUR CO ALARM

WELCOME CHIRP

Horn chirps and light blinks once when batteries are first connected.

DIGITAL DISPLAY: All segments are turned

on for a short time upon initial power.

Then the battery level icon is displayed.

ALARM RECEIVING BATTERY POWER

Light flashes every minute. Horn is silent.

DIGITAL DISPLAY: Battery icon will show a full or almost

full icon.

INSTALLING THE AA BATTERIES

1. Flip the battery door down to open.

2. Install both AA batteries

(included) inside the battery

compartment as indicated.

Make sure the “+” and “–”

ends of each battery are

aligned properly.

3. Close the battery door.

HOW TO INSTALL YOUR CO ALARM

Read “Where To Install CO Alarms” before starting.

Before you start installation,find the pair of self-adhesive labels included

with this CO Alarm. On each label write in the phone number of your emer-

gency responder (like 911) and a qualified appliance technician. Place one

label near the CO Alarm, and the other label in the “fresh air” location you

plan to go if the alarm sounds.

IF YOUR CO ALARM SOUNDS

Actuation of your CO Alarm indicates the presence of carbon monoxide

(CO) which can kill you. In other words, when your CO Alarm sounds,

you must not ignore it!

IF THE ALARM SIGNAL SOUNDS:

1. Operate the Test/Silence button.

2. Call your emergency services, fire department or 911. Write down the

number of your local emergency service here:

__________________________________________________________________

3. Immediately move to fresh air—outdoors or by an open door or window.

D nt to check that all persons are accounted for. Do not re-o a head cou

enter the premises, or move away from the open door or window until the

emergency services responder has arrived, the premises have been aired

out, and your CO Alarm remains in its normal condition.

4. After following steps 1-3, if your CO Alarm reactivates within a 24-hour

period, repeat steps 1-3 and call a qualified appliance technician to inves-

tigate for sources of CO from fuel-burning equipment and appliances, and

inspect for proper operation of this equipment. If problems are identified

during this inspection have the equipment serviced immediately. Note any

combustion equipment not inspected by the technician, and consult the

manufacturers’ instructions, or contact the manufacturers directly, for more

information about CO safety and this equipment. Make sure that motor

vehicles are not, and have not, been operating in an attached garage or

adjacent to the residence. Write down the number of a qualified appliance

technician here:

_________________________________________________________________

Alarms have various limitations. See "General Limitations of CO Alarms"

for details.

USING THE SILENCE FEATURE

• The Silence Feature is for your convenience only and will not

correct a CO problem. Always check your home for a potential

problem after any alarm. Failure to do so can result in injur y or

death.

• NEVER remove the batteries from your CO Alarm to silence the

horn. Use the silence feature. Removing the batteries removes

your protection! See “If Your CO Alarm Sounds” for details on

responding to an alarm.

The Silence Feature is intended to temporarily silence your CO Alarm’s alarm

horn while you correct the problem—it will not correct a CO problem. While

the alarm is silenced it will continue to monitor the air for CO.

To Activate the Silence Feature Manually:

Press and hold the Test/Silence button until the horn is silent.

To Activate the Silence Feature Using Your Remote Control:

Standing no farther than 12 feet (3.6 meters) away, point your remote control at

the cover of the CO Alarm and push the VOLUME or CHANNEL button. Hold

the button down for at least 5 seconds.

Once you activate the Silence Feature: the Silence cycle will last

approximately 4 minutes.

NOTE: After initial 4-minute Silence cycle, the CO Alarm re-evaluates present

CO levels and responds accordingly. If CO levels remain potentially danger-

ous—or start rising higher—the horn will start sounding again.

While the detector is silenced:

If the CO Alarm...

Is silent for only 4 minutes, then

starts sounding loudly—4 beeps,

pause, 4 beeps, pause

This means...

CO levels are still potentially

dangerous.

If the CO Alarm...

Remains silent after you pressed

the Test/Silence button

This means...

CO levels are d opr ping.

TO MOUNT ON THE WALL

Tools you will need: pencil, drill with 3/16” or 5mm drill bit,

fla thead screwdriver, hammer.

1. Choose a location on the wall. Do not install the Alarm closer than 4”

(102 mm) from where the wall meets the ceiling.

2. Hold the mounting guide template against the wall, and make a mark

inside each keyhole where you will drill your mounting hole as shown in

the diagram below.

3. Use a 3/16” (5 mm) drill bit to drill through the marks you made for the

mounting holes.

4. Insert the plastic screw anchors into the mounting holes until they are

flush with the wall. If necessary, tap them gently with a hammer.

5. Insert the screws into the anchors until the screwhead is 1/8 inch (3 mm)

away from the wall.

6. Slide the CO Alarm onto the screws until you feel it click into place.

7. Test the CO Alarm as described in “Weekly Testing.”

“ALARM-MOVE TO FRESH AIR”

If you hear the alarm horn and the Red light is flashing,

move everyone to a source of fresh air.

DO NOT disconnect the batteries from the CO Alarm!

SILENCING THE LOW BATTERY WARNING

This silence feature can temporarily quiet the low battery warning “chirp” for

up to 8 hour its w hout having to remove the batteries. You can silence the low

battery warning “chirp” two ways:

1. Manually: Press the Test/Silence button on the alarm cover.

2. Using Your Remote Control: Standing no further than 12 feet (3.6 meters)

away from the CO Alarm, aim your IR remote at the CO Alarm and press

the CHANNEL or VOLUME button for at least 3-5 seconds.

After 8 hours, the low battery “chirp” will resume. Replace the batteries as

soon as possible; this unit will not operate without battery power!

To deactivate this f ture: ea Press the Test/Silence button again. The unit will

go into Test Mode and the low battery warning will resume (LED flashes and

unit sounds “chirp” once a minute.)

If you canno it s lence the low battery warning, replace the batteries

immediately.

Mounting Guide Template

2.5 inches (64 mm)

Product specificaties

Merk:	First Alert
Categorie:	Niet gecategoriseerd
Model:	CO410

Heb je hulp nodig?

Als je hulp nodig hebt met First Alert CO410 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd First Alert

First Alert KFE2S5 Handleiding

30 Augustus 2023

First Alert SCO500 Handleiding

30 Augustus 2023

First Alert FESA5 Handleiding

30 Augustus 2023

First Alert PIR725 Handleiding

30 Augustus 2023

First Alert WA100 Handleiding

30 Augustus 2023

First Alert SCO403 Handleiding

9 Mei 2023

First Alert SA511CN2 Handleiding

1 Mei 2023

First Alert SC7010BV Handleiding

12 April 2023

First Alert SA521CN Handleiding

12 April 2023

First Alert SC7010B Handleiding

10 April 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Playtive IAN 327221 Handleiding

1 Mei 2024

Samsung UN32J4001AF Handleiding

1 Mei 2024

Bauknecht KSI 18GF2 P2 Handleiding

27 April 2024

Fakir Artemis TS 150 Handleiding

26 April 2024

Sony UTX-M03 Handleiding

26 April 2024

Sony URX-P03 Handleiding

26 April 2024

Sony WRU-806B Handleiding

26 April 2024

Sony UTX-B03 Handleiding

26 April 2024

Sony UTX-P03 Handleiding

26 April 2024

Sony ODS-L10 Handleiding

26 April 2024