Festo EAPM-L2-SH Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Festo EAPM-L2-SH (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
Translation of the original instructions
Š 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product www.festo.com/sp.è
Document Product
Actuator … 3 5
Proximity switch
User documents
Switch lug
Tab. 1
2 Safety
2.1 Safety instructions
– Only mount the product on components that are in a condition to be safely
operated.
– Observe tightening torques. Unless otherwise specified, the tolerance is
±20%.
2.2 Intended use
2.2.1 Use
Mounting of a proximity switch for sensing the slide position on the basic profile
of an actuator … 3 5
2.3 Training of qualified personnel
Work on the product may only be carried out by qualified personnel who can eval
uate the work and detect dangers. Personnel must have the relevant mechanical
training.
3 Additional information
– Accessories www.festo.com/catalogue.è
– Spare parts www.festo.com/spareparts.è
4 Product Range Overview
4.1 Scope of delivery
1Sensor bracket (1x)
2Threaded pin (2x)
Fig. 1
4.2 Not in scope of delivery
Mini slide unit EGSS (1x)/spindle axis unit ELGS (1x)/electric cylinder unit EPCS
(1x) or the following actuators:
3Mini slide EGSC (1x)
4Guide axis ELFC/spindle axis
ELGC (1x)
5Electric cylinder EPCC (1x)
Fig. 2
5 Assembly
5.1 Attachment to mini slide
The sensor bracket can also be mounted on the opposite side. However, in this1
case a switch lug cannot be mounted.
Fig. 3
– Position sensor bracket in the slot[A] as shown. 1
– Tighten threaded pins . Tightening torque: 0.7Nm2
èSensor bracket is jammed in the slot[A].1
5.2 Attachment to guide/spindle axis
The sensor bracket can also be mounted on the opposite side. A switch lug can1
be mounted on both sides.
Fig. 4
– Position sensor bracket in the slot[A] as shown. 1
– Tighten threaded pins . Tightening torque: 0.7Nm2
èSensor bracket is jammed in the slot[A].1
5.3 Attachment on electric cylinder
The sensor bracket can be mounted on three sides. A switch lug cannot be1
mounted.
Fig. 5
– Position the sensor bracket in the slot[A] so the sensor will later be in the1
middle of the profile.
– Tighten threaded pins . Tightening torque: 0.7Nm2
èSensor bracket is jammed in the slot[A].1
8135693
EAPM-L2-SH
Sensor bracket
8135693
202101a
[8135695]
Assembly instructions
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 3470
www.festo.com


Product specificaties

Merk: Festo
Categorie: Niet gecategoriseerd
Model: EAPM-L2-SH

Heb je hulp nodig?

Als je hulp nodig hebt met Festo EAPM-L2-SH stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Festo

Festo

Festo VPPI Handleiding

21 November 2024
Festo

Festo SFAB Handleiding

21 November 2024
Festo

Festo SFAH Handleiding

21 November 2024
Festo

Festo DRRD-12 Handleiding

21 November 2024
Festo

Festo SDE3 Handleiding

21 November 2024
Festo

Festo SFTE Handleiding

21 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd