Festo EAHM-E15-60-E22 Handleiding

Festo Niet gecategoriseerd EAHM-E15-60-E22

Lees hieronder de 📖 handleiding in het Nederlandse voor Festo EAHM-E15-60-E22 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 16 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
EAHM-E15-...-E22
Mounting kit
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Deutschland
+49 711 347-0
www.festo.com
Assembly instructions
8156951
2021-07
[8156953]
Translation of the original instructions
© 2021 all rights reserved to Festo SE & Co. KG
1 Applicable documents
All available documents for the product
è www.festo.com/sp.
Document Product Table of contents
Operating instructions Handling system YXCA/YXCF/
YXCR
Assembly
Tab. 1: Applicable documents
2 Safety
2.1 Safety instructions
–Before working on the product, switch off the power supply and secure it
against being switched on again.
–Observe further applicable documents.
–Observe tightening torques.
2.2 Intended use
Mounting the X-axes ELGC or a handling system YXCA/YXCF/YXCR.
3 Additional information
Accessories of the handling system YXCA/YXCF/YXCR
è
www.festo.com/cata-
logue
4 Product Range Overview
4.1 Scope of delivery
1
2
3
Fig.1
1
Mounting flange (1x)
2
Screw (8x)
M5x12
3
Profile mounting (2x)
4.2 Not in scope of delivery
4
Fig.2
4
X-module (1x)
EHMX-...-ELGC
5 Assembly
Fig.3
• Observe the number of mounting kits and the support spacings X2 (
è 1
Applicable documents).
Centring pins facilitate subsequent replacement of the actuator.
• The hole [A] is intended for optional centring of a profile mounting with a3
centring pin.
2
1A
Fig.4
EAHM-E15-...-E22 60 80
X3 [mm] 68 68
Y2 [mm] 80 100
Tab. 2: Hole spacing
•Fasten the mounting flange to the mounting surface with four screws .1 2
Tightening torque: 6 Nm ± 20%
3B
C
Fig.5
1. Align the X-axes precisely together (
è 1 Applicable documents).
2. Push the lugs [C] of the profile mountings into the profile slots [B].3
2
3
D
A
Fig.6
EAHM-E15-...-E22 60 80
Drilled hole [A] for centring
pin [D]
[mm] 5 H8Æ
Tab. 3: Drilled hole for centring pin
1. Optionally fasten the profile mounting with centring pin [D] to the3
mounting flange .1
2. Fasten both profile mountings with the screws to the mounting3 2
flange . Tightening torque: 4.8 Nm ± 20% 1


Product specificaties

Merk: Festo
Categorie: Niet gecategoriseerd
Model: EAHM-E15-60-E22

Heb je hulp nodig?

Als je hulp nodig hebt met Festo EAHM-E15-60-E22 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Festo

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd