Festo DARD-L8-25-S Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Festo DARD-L8-25-S (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Translation of the original instructions
LOCTITE 243Ž is a registered trademark of its respective trademark holder in cer
tain countries.
1 Further applicable documents
All available documents for the product www.festo.com/pk.è
Observe further applicable documents:
– Operating instructions of the linear drive5
2 Safety
2.1 Safety instructions
– Before working on the product, switch off the power supply and secure it
against being switched on again.
– Observe tightening torques. Unless otherwise specified, the tolerance
is±10%. Tightening torques 5 Technical data.è
– Observe the safety data sheet for the adhesive from the original manufac
turer.
2.2 Intended use
Compensating element between the slide(A) of the linear drive and the pay5
load to be moved.
3 Product range overview
3.1 Scope of delivery
1Moment compensator (1x)
2Adhesive LOCTITE 243 (1x)
3Threaded pin (1x)
4Screw (3x)
Fig. 1
3.2 Not in scope of delivery
5Linear drive DLGFG (1x)
Fig. 2
4 Mounting
Positioning the moment compensator
Fig. 3
• Place the moment compensator opposite the sensor slot(X) flush with the1
slide(A).
ÄThe sensor slot(X) is freely accessible.
Attaching the moment compensator
Fig. 4
• Use the screws to attach the moment compensator to the slide(A). Do4 1
not tighten screws .4
Mounting the moment compensator
Fig. 5
1. Apply adhesive to the threaded pin .2 3
2. Screw the threaded pin into the moment compensator .3 1
3. Tighten the threaded pin .3
4. Tighten the screws .4
4.1 Mounting the payload
Hole for spring pin(B)
Fig. 6
• Hole for spring pin(B) provided for centring the payload.
Recommended hole for spring pin(B): 5.2Æ+0.1mm
Mounting the payload on DARD-L8-20/25-S
Fig. 7
• Mount payload with recommended screws using hole(C) or(D) on the
moment compensator .1
Hole(C) Hole(D)
Hole thread M5 M5
Recommended screws 2xM58.8 2xM48.8 ISO4762ß
Recommended tightening torques [Nm] 4.5 2.6
Tab. 1
When mounting the payload using hole(D), the threaded holeM5(C) serves as a
through hole for the screwM4.
8084730
Moment compensator
DARD-L8
8084730
201802a
[8084732]
Instructions| Assembly
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 3470
www.festo.com
Mounting the payload on DARD-L8-32/40-S
Fig. 8
• Mount payload with recommended screws using hole(E) or(F) on the
moment compensator .1
Hole(E) Hole(F)
Hole thread M5 –
ß 2xM58.8 2xM410.9
ISO4762
Recommended screws
Recommended tightening torques [Nm] 5 3.7
Tab. 2
5 Technical data
5.1 Screw sizes and tightening torques MA
DARD-L8 20 25 32 40
ß M4x18 M4x18 M4x22 M4x224Screw
ISO4762 [Nm] 3 3 3.4 3.4
3 Threaded pin [Nm] 1 1 1 1
Tab. 3


Product specificaties

Merk: Festo
Categorie: Niet gecategoriseerd
Model: DARD-L8-25-S

Heb je hulp nodig?

Als je hulp nodig hebt met Festo DARD-L8-25-S stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Festo

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd