Festo DADM-TK-90 Handleiding

Festo Niet gecategoriseerd DADM-TK-90

Lees hieronder de 📖 handleiding in het Nederlandse voor Festo DADM-TK-90 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Assembly instructions (Original instructions)
8072099
2017-05d
[8072101]
†‡
Reciprocating motion kit
DADM-TK
Festo SE & Co. KG
Ruiter Straße 82
73734 Esslingen
Germany
+49 711 347-0
www.festo.com
1. Applicable documents
All available documents for this product  www.festo.com/pk
 Operating instructions for rotary indexing table 5
2. Safety
Observe the safety information ( Applicable documents).
Comply with tightening torques ( Table).
3. Intended use
Reciprocating motion kit DADM-TK:
Conversion of the rotary indexing table DHTG to reciprocating motion.
4. Scope of delivery
11377d_1
1 Shock absorber
2 Stop pin with O-ring
3 Retaining ring
DIN 472
4 Flat seal
(1x)
(4x)
(1x)
(4x)
5. Not in scope of delivery
11377d_12
5 Rotary indexing
table DHTG
(B) Stop plate
(H) Shock absorber
plate
(1x)
(1x)
(1x)
6. Screw sizes and tightening torques MA1)
DADM-TK 65 90 140 220
2 Stop pin M4
[Nm] 1.5
(A) Screw M5x16 (3x) M5x16 (5x) M6x16 (5x) M6x20 (5x)
[Nm] 2.9 5.9
(F) Flow control
valve
GRLA-M5-B GRLA-1/8-QS-8-D
[Nm] 1.5 5.5
(G) Screw M4x16 (4x) M4x16 (5x) M6x16 (6x) M6x25 (6x)
[Nm] 2.9 9.9
1) Tolerance for tightening torques MA without indication of tolerance ± 20 %
7. Preparations for mounting
Unlock rotary indexing table 5 ( Applicable documents).
To unlock:
Pressurize the supply port A with at least 4 bar.
 The rotary table can be turned freely.
Switch off compressed air.
Exhausting the rotary indexing table.
8. Mounting
11
37
7d
_6
Unscrew screws (A).
Remove stop plate (B).
11377d_13
Check stop plate (B).
The stop plate (B) contains
drill holes (E) or threads (E).
– For drill holes (E)
 Section 8a.
– For threads (E)
 Section 8b.
8a. For drill holes (E)
11377d_25
Remove O-rings (C) from
the drill holes (D).
11377d_26
Place two seals 4 on
the drill holes (D).
11377d_9
Fasten the stop plate (B)
using the screws (A).
11377d_2
Unscrew flow control
valve (F).
Unscrew screws (G).
Remove shock absorber
plate (H).
11377d_3
Remove O-rings (J) from
the drill holes (K).
11377d_4
Place two seals 4 on
the drill holes (K).
Turn the rotary table.
 Left drive piston (L) comes
forward 2).
Push the shock absorber 1
into the drive piston (L).
Fasten the shock
absorber 1 with the
retaining ring 3.
Check remaining O-rings
for correct fit.
11377d_5
Fasten shock absorber
plate (H)3) with the
screws (G).
Screw throttle valve (F)
in tightly.
11377d_10
Remove the plugs (M)
and (N).
Information
Four stop pins 2 and four O-rings (J) are left over.
8b. For threads (E)
11377d_24
Tighten two stop pins 2
in the threads (E) of the
stop plate (B).
11377d_27
Fasten the stop plate (B)
using the screws (A).
11377d_2
Unscrew flow control
valve (F).
Unscrew screws (G).
Remove shock absorber
plate (H).
11377d_21
Tighten two stop pins 2
in the threads (O) of the
shock absorber plate (H).
11377d_22
Turn the rotary table.
 Left drive piston (L)
comes forward 2).
Push the shock absorber 1
into the drive piston (L).
Fasten the shock
absorber 1 with the
retaining ring 3.
Check all O-rings for
correct fit.
11377d_23
Fasten shock absorber
plate (H)3) with the
screws (G).
Screw throttle valve (F)
in tightly.
11377d_10
Remove the plugs (M)
and (N).
Information
Four seals 4 are left over.
2) 3)
9. After mounting
During reciprocating motion, locking is separated from rotation.
Always actuate turn (right/left) and unlock/lock with a controller
accordingly ( Applicable documents).
2) In case of division > 2 (BG65 and 90)/ > 3 (BG140 and 220):
There is a spacing bolt in front of the left drive piston (L). Remove the spacer bolt during
dismantling and insert it again during mounting.
3) For division > 2:
When attaching the shock absorber plate, place the small compression spring back into
the drill hole (X) so that it presses on the spacer bolt.
1
3
4
N
M
4
X2
)
D
1
3
4
B
A
J
K
L
A
B
F
H
G
2
E
B
A
F
H
G
2
B
E
5
B
F
H
G
1
3
L
2
H
O
X2
)
F
H
G
N
M
K
C
D
H
B

Product specificaties

Merk: Festo
Categorie: Niet gecategoriseerd
Model: DADM-TK-90

Heb je hulp nodig?

Als je hulp nodig hebt met Festo DADM-TK-90 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Festo

Festo

Festo DADM-CK-90-12 Handleiding

30 Maart 2025
Festo

Festo DFM-32-50-B-PPV-A-GF Handleiding

30 Maart 2025
Festo

Festo DADP-SP-G9-16-F Handleiding

30 Maart 2025
Festo

Festo CMMT-AS-C18-11A-P3-MP-S1 Handleiding

30 Maart 2025
Festo

Festo CRDSNU-B-25-125-PPS-A-MG-A1 Handleiding

30 Maart 2025
Festo

Festo DFM-50-50-B-PPV-A-KF Handleiding

30 Maart 2025
Festo

Festo DADG-AK-G8-20-150 Handleiding

30 Maart 2025
Festo

Festo NEBM-L10G14-EH-2.5-Q7N-LE12 Handleiding

30 Maart 2025
Festo

Festo CRDSNU-25-20-P-A Handleiding

30 Maart 2025
Festo

Festo DADP-SP-G9-6-F Handleiding

30 Maart 2025

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Panasonic

Panasonic Lumix DMW-AC11 Handleiding

9 April 2025
Soundstream

Soundstream VRN-64HBL Handleiding

9 April 2025
MOZA

MOZA SR-P Handleiding

9 April 2025
Creality3D

Creality3D Ender-3 S1 Pro Handleiding

9 April 2025
Act

Act AC6020 Handleiding

9 April 2025
BlueBuilt

BlueBuilt BBMA2M Handleiding

9 April 2025
Act

Act AC6015 Handleiding

9 April 2025
Diamond Audio

Diamond Audio MSHD9813SG Handleiding

9 April 2025
Daikin

Daikin ETVZ12S18EJ6V Handleiding

9 April 2025
Daikin

Daikin FXFQ80AVEB Handleiding

9 April 2025