Festo DADM-CK-90-2 Handleiding

Festo Niet gecategoriseerd DADM-CK-90-2

Lees hieronder de 📖 handleiding in het Nederlandse voor Festo DADM-CK-90-2 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Assembly instructions (Original: de)

8059334

1604c

[8059336]

†‡

Indexing conversion kit

DADM-CK

Festo SE & Co. KG

Postfach

73726 Esslingen

Germany

+49 711 347-0

www.festo.com

1. Parts lists

1a. Parts list DADM-CK-65/-90

11768d_1

1 Spacing bolt1)

2 Index plate

3 Stop bolt1)

4 Screw

5 Special grease

LUB-E1

(free of silicone)

(2x)

(1x)

(3x)

(1x)

1b. Parts list DADM-CK-140/-220

11768d_1

1 Spacing bolt1)

2 Index plate

3 Stop bolt1)

4 Screw

5 Special grease

LUB-E1

(free of silicone)

(2x)

(1x)

(6x)

(1x)

1c. Not in scope of delivery

11768d_25

6 Rotary indexing

table DHTG

7 Rotating plate

8 Clamping ring

9 Screw

(1x)

2. Intended use

Indexing conversion kit DADM-CK:

Conversion of the rotary indexing table 6 to a different spacing.

3. Safety instructions and notes on mounting

Switch off compressed air before mounting work.

Exhausting rotary indexing table 6.

Observe tightening torques ( Section 6).

Information copies

Applicable documents 





www.festo.com/sp

 Rotary indexing table DHTG operating instructions

 Assembly instructions for energy throughfeed DHTG-P4

4. Preparations for mounting

Disassemble the energy throughfeed DHTG-P4 ( applicable documents).

Grease all movable parts of the indexing conversion kit using the

grease 5.

The rotary table 7 must be turning freely.

To unlock:

Pressurise port “A” with minimum 4 bar.

1) With DADM-CK-65-2, DADM-CK-90-2, DADM-CK-140-3, DADM-CK-220-3 there are no spacing

bolts 1 included in the scope of delivery ( Section 7).

5. Mounting

5a. Disassembly of the rotary table 7

11768d_3

Mark the rotary table 7 and

the clamping ring 8 at the

notch (B) that corresponds

to the countersink of the

screw 9.

Untighten screw 9.

11768d_4

Turn open the clamping

ring 8 with the help of

2 cylindrical dowel

pins (C)2)..

Sizes for cylindrical dowel

pins (C):

DHTG-65: 2 x 2m6

DHTG-90 … -220: 2 x 3m6

Remove the caged ball

bearings (D).

11768d_5

Pull the rotary table 7

up and out with the help

of 2 screws (E)3) .

Thread for screws (E):

DHTG-65/-90: M4

DHTG-140: M6

DHTG-220: M8

Turn the rotating plate 7.

5b. Assembly of the index plate 4

44.

11768d_6

Unscrew screws (F).

11768d_7

Tighten the screws (F) in the

threads (G).

Force away the index

plate (H) from the rotating

plate 7 by means of the

screws (F).

11768d_8

Position the index plate 2

on the rotating plate 7.

Fasten the index plate 2

with the screws 4.

11768d_9

Observe the index holes (I).

Turn the rotating plate 7.

5c. Assembly of the rotary table 7

11768d_14

Check: The index holes (I) are

located above the index

bolts (J).

Place the rotating plate 7

on the rotary indexing ta-

ble 6.

2) The cylindrical dowel pins (C) are not included in the scope of delivery.

3) The screws (E) are not included in the scope of delivery.

11768d_15

Place the ball bearing

cage (D) in the rotary index-

ing table 6.

Tighten the clamping ring 8

by means of the cylindrical

dowel pins (C).

Untighten and remove the

cylindrical dowel pins (C).

11768d_16

Check: The marks on the

rotating plate 7 and on the

clamping ring 8 match at

the notch (B).

Tighten screw 9.

5d. Assembly of spacing bolt 1

11768d_17

Turn open the clamping

component (K) by 1 turn.

Unscrew the stop screw (L).

11768d_18

Unscrew flow control

valve (M).

Untighten screw (N).

Carefully remove the sub-

base (O). Make sure not to

lose the compression

spring (P) and the seals.

11768d_19

Unscrew screws (Q).

Carefully remove the stop

plate (R). Make sure not to

lose the seals.

11768d_20

Remove the split pins (S)

from the hole to their left.

11768d_21

Push the existing split

pins 11) into the holes on

the left ( section 7).

With the split pins insert-

ed 11):

Position the compression

spring (P) in the hole of the

sub-base (O).

Without the split pins 11) in-

serted:

Remove the compression

spring (P)4) .

Check: Correct fit of the seals.

Fasten the sub-base (O) us-

ing screws (N).

11768d_22

4) Without the split pin 1 mounted, no counter pressure is acting on the compression

spring (P), which causes function failure of the rotary indexing table 6.

Screw in and tighten the

throttle valve (M).

11768d_23

Check: Correct fit of the seals.

Fasten the stop plate (R) us-

ing the screws (Q).

11768d_24

Screw in the existing stop

bolt 3 ( Section 7).

Check: The required cushion-

ing is achieved.

Tighten the clamping com-

ponent (K).

Pressurise the rotary indexing table 6.

The rotary table must not turn freely.

To lock:

Pressurise port “B” with minimum 4 bar.

If the rotary table 7 is still rotating freely:

Manually turn the rotary table 7 until the index bolts (I) engage.

6. Screw sizes and tightening torques MA

DADM-CK- 65 90 140 220

(K) Clamping

component

ß 2.5 4

[Nm]

0.8 2.5

(M) Flow

control valve

GRLA-M5-B GRLA-G1/8

[Nm]

1.5 5.5

(N) Screw M4x16 M6x16 M6x25

[Nm]

3 10

(Q) Screw M4x16 M5x16 M6x16 M6x20

[Nm]

1.5 3 6

4 Screw M4x8 M5x12 M5x16 M6x16

[Nm]

2 4 7

9 Screw M3x6

[Nm]

0.6

7. Lengths of the split pins 1

11 and stop bolts 3

331)

DADM-CK- 65 90 140 220

Spacing Pin

2 1 [mm]

————

3 [mm]

12 12 — —

3 1 [mm]

11.31 15.71 — —

3 [mm]

23.3 28 14 19

4 1 [mm]

16.96 23.56 12.57 25.13

3 [mm]

29 35.5 26.5 44.1

6 1 [mm]

22.62 31.42 25.13 50.27

3 [mm]

34.6 43.5 39 69.3

8 1 [mm]

25.45 35.34 31.42 62.83

3 [mm]

37.5 47.5 45.5 81.8

12 1 [mm]

28.27 39.27 37.7 75.4

3 [mm]

40.3 51.5 51.5 94.4

24 1 [mm]

31.1 43.2 43.98 87.97

3 [mm]

45 55.5 58 107

8. Prior to commissioning

Cushioning setting and commissioning ( applicable document).

5) Tolerances for tightening torques MA without tolerance details

MA , 0.60 … 1.00 Nm: ± 30 %

MA , 1.0 Nm: ± 20 %

Product specificaties

Merk:	Festo
Categorie:	Niet gecategoriseerd
Model:	DADM-CK-90-2

Heb je hulp nodig?

Als je hulp nodig hebt met Festo DADM-CK-90-2 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Festo

Festo CPX-AP-I Handleiding

20 December 2024

Festo VAEM-V-S8EPRS2 Handleiding

20 December 2024

Festo VPPI Handleiding

21 November 2024

Festo VAVE-P17-TP-5YL1-P Handleiding

21 November 2024

Festo SD-SUB-D-BU9 Handleiding

21 November 2024

Festo SAMH-F12-MK Handleiding

21 November 2024

Festo SFAB Handleiding

21 November 2024

Festo SASC-P4-A-M8-S Handleiding

21 November 2024

Festo SFAH Handleiding

21 November 2024

Festo DRRD-12 Handleiding

21 November 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Gourmetmaxx 03863 Handleiding

24 December 2024

Vello PGS-P Handleiding

24 December 2024

Venom Quad Charging Station VS4796 Handleiding

24 December 2024

Nec IPJ2000CM Handleiding

24 December 2024

Monogram ZKPN Handleiding

24 December 2024

Philips Quick Clean Pot QCP10 Handleiding

24 December 2024

Philips Senseo HD7002 Handleiding

24 December 2024

D-Link DUB-C2 Handleiding

24 December 2024

Nec MultiPresenter Stick DS1-MP10RX1 Handleiding

24 December 2024

Nec DS1-TM01 Handleiding

24 December 2024