Ferm fbf 8 e Frezen Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Ferm fbf 8 e Frezen (22 pagina's) in de categorie Frezen. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/22
Ferm b.v. • P.O. Box 134 • 8280 AC Genemuiden NL Web: www.ferm.com 0110/26-1
Art.nr. 326120
FBF-8E
UK Subject to change
D Änderungen vorbehalten
NL Wijzigingen voorbehouden
F Sous réserve de modifications
SV Ändringar förbehålles
SU Pidätämme oikeuden muutoksiin
NO Rett till endringer forbeholdes
DK Ret til ændringer forbeholdes
USERS MANUAL
Router 02
GEBRAUCHSANWEISUNG
Oberfräse 07
GEBRUIKSAANWIJZING
Bovenfrees 12
MODE D’EMPLOI
Défonceuse 17
BRUKSANVISNING
Överfräs 22
KÄYTTÖOHJE
Yläjyrsin 27
BRUKSANVISNING
Overfres 32
BRUGER VEJLEDNING
Overfladefræser 37
GB
D
NL
F
S
SF
N
DK
Ferm 43
Router
The following symbols are used in these instructions for
use:
Denotes risk of personal injury, loss of life or da-
mage to the tool in case of non-observance of
the instructions in this manual.
Denotes risk of electric shock.
Carefully read this manual before using the machine. Ma-
ke sure that you know how the machine functions and how
to operate it. Maintain the machine in accordance with the
instructions to make sure it functions properly. Keep this
manual and the enclosed documentation with the machi-
ne.
SAFETY INSTRUCTIONS
When using electric machines always observe the
safety regulations applicable in your country to redu-
ce the risk of fire, electric shock and personal injury.
Read the following safety instructions and also the
enclosed safety instructions.
Keep these instructions in a safe place!
• Check workpieces for any protruding nails etc. and re-
move these.
• Keep your hands away from the surface to be cut.
TECHNICAL SPECIFICATIONS
Voltage 230 V~
Frequency 50 Hz
Power input 850 W
No load speed 9000-27000/min
Max. cutter diameter 30 mm
Cutting depth 35 mm
Collet 8 mm
Weight 3.8 kg
Lpa(sound pressure) 83 dB(A)
Lwa
(sound power) 96 dB(A)
Vibration value 3.3 m/s2
Electrical safety
Always check that the power supply corre-
sponds to the voltage on the rating plate.
Your machine is double insulated in accordance
with EN 50144; therefore no earthwire is requi-
red.
Replacing cables or plugs
Immediately throw away old cables or plugs when they ha-
ve been replaced by new ones. It is dangerous to insert the
plug of a loose cable in the wall outlet.
Using extension cables
Only use an approved extension cable suitable for the po-
wer input of the machine. The minimum conductor size is
1.5 mm2. When using a cable reel always unwind the reel
completely.
PACKAGE CONTENTS
1 router
1 cutter
1 parallel guide
1 guide bush
2 screws
2 nuts
1 adapter for dust extraction
1 wrench
1 instruction manual
1 safety instructions
1 guarantee card
Check the machine, loose parts and accessories for trans-
port damage.
GB English
2Ferm
EXPLODED VIEW
42 Ferm
PRODUCT INFORMATION
Fig. A.
The FBF-8E router has been designed for professional
routing of wood, wood products and plastics.
1 on/off switch
2 handle
3 router base
4 locking bolt for parallel guide
5 opening for parallel guide
6 collet nut
7 spindle lock
8 revolver-depth stop
9 locking bolt depth stop
10 depth stop
11 clamping lever
12 scale cutting depth
13 adjusting wheel electronic speed control
MOUNTING ACCESSORIES
Fig. B.
Prior to mounting an accessory always unplug the tool.
Mounting and removing cutters.
Only use cutters with a shaft diameter which corresponds
with the size of the collet. Only use cutters which are suited
for the maximum speed of the machine. The cutter diame-
ter should not exceed the maximum diameter (see ‘Tech-
nical specifications’).
• Press the spindle lock (7) and turn the collet nut (6) until
it engages in the lock. Keep the spindle lock pressed
during this procedure.
• Open the collet nut using the wrench.
• Place the cutter shaft in the collet.
• Tighten the collet nut so that the cutter is locked pro-
perly.
• Open the collet nut when you want to replace a cutter.
Wait until the machine has come to a complete
standstill and the cutter has cooled down before
replacing a cutter.
Ferm 3
SPARE PARTS LIST
REF.NR. DESCRIPTION FERM NR.
01 +02 RUBBER FOOT COMPLETE 408450
03 ENCLOSURE COMPLETE 408451
05 SWITCH 408452
06 ROTOR 408243
08 STATOR 408244
09 + 10 + 11 CARBON BRUSHSET + HOLDER 408245
17 + 22 SANDING PAD COMPLETE 408453
28 FAN 408252
DUST BAG 408249
Product specificaties
| Merk: | Ferm |
| Categorie: | Frezen |
| Model: | fbf 8 e Frezen |
Heb je hulp nodig?
Als je hulp nodig hebt met Ferm fbf 8 e Frezen stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Frezen Ferm
27 Juni 2023
27 Juni 2023
Handleiding Frezen
- Frezen DeWalt
- Frezen Elu
- Frezen Kress
- Frezen Makita
- Frezen Parkside
- Frezen Powerplus
- Frezen Ryobi
- Frezen Toledo
Nieuwste handleidingen voor Frezen
25 September 2023
2 Augustus 2023
12 Maart 2023
30 Maart 2023
2 April 2023
22 December 2022
27 Oktober 2022
27 Oktober 2022
27 Oktober 2022
27 Oktober 2022