Fantini Cosmi Intellicomfort+ Handleiding

Fantini Cosmi Thermostaat Intellicomfort+

Lees hieronder de 📖 handleiding in het Nederlandse voor Fantini Cosmi Intellicomfort+ (2 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 46 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

WIRELESS RADIATOR ACTUATOR

The O60RF wireless actuator replaces the sensor head or the control knob already existing on the radiator valve with thermostatic option. The actuator opens

or closes the hot water ﬂ ow in order to provide the best climatic comfort based on the temperature set by CH120RF/CH180RF room thermostats.

SCOPE OF DELIVERY

1 O60RF actuator, 1 coupling ring, 1 adapters set with four parts, 1 screw and nut, 1 removing tool and this installation manual.

INSTALLATION

BATTERIES INSERTING

• In order to insert the batteries, remove before the battery ﬂ ap as indicated in the picture 1.

• Insert two AA 1,5V alkaline batteries matching the polarity showed in the battery compartment. Only at

the ﬁ rst batteries insertion the actuator goes into mounting position and it stays in this position until the

commissioning procedure is ﬁ nished.

MOUNTING

ATTENZIONE

The wireless actuator can be quickly and easily mounted on all common valves with 30x1,5 thread, as indicated

below:

• Screw the white coupling ring (B) on the valve (A) so that the pin does not stick out by more than 1 mm. from

the edge of the white ring.

• Put the actuator (C) on the white coupling ring (B) until the “click” feedback conﬁ rms the hooking.

WARNING: never turn the actuator on the coupling ring because this operation will damage the device.

Picture 1

Picture 2

VALVE ADAPTERS

Picture 3

ACTUATOR DISMOUNTING

ATTENZIONE

If necessary, in order to remove the actuator from the coupling ring, operate as indicated below:

• Insert both tips of the supplied tool (I) into the two holes;

• Press tool in the holes and remove the actuator.

WARNING: never turn the actuator on the coupling ring because this operation will damage the device.

COMMISSIONING AND NETWORK INCLUSION

The actuator will works only after the network inclusion step. For this procedure it’s necessary to use a special

“conﬁ guration tool” that provides all instructions by display messages. When required, will be necessary to touch

the “X” area of the actuator with the tool (see picture 5).

For more details, please refer to the wireless multi-zone system manual.

TECHNICAL DATA

Power supply: 2 batteries 1,5V type AA;

Transceiver frequency: 868MHz

Degree of protection: IP30;

Operating temperature: 0 ÷ 50°C;

Storage temperature: -20 ÷ +70°C;

Shape type: white ABS plastic;

Dimensions: 48x63x74mm;

Valve connection: M30x1,5.

Complies with Directive 2004/108 / EC;

Responding to Directive 2014/53 / EU (RED).

Picture 4

Picture 5

Fantini Cosmi S.p.a. Via dell’Osio, 6 20090 Caleppio di Settala MI - ITALY

Tel. 02 956821 I Fax 02 95307006 I info@fantinicosmi.it I http://www.fantinicosmi.it

SUPPORTO TECNICO: supportotecnico@fantinicosmi.it

EXPORT DEPARTMENT Tel. ++39 02 95682222 I export@fantinicosmi.it

5679806A

BRAND CODE

unnecessary

included

unnecessary

One of the enclosed adapters is required for installation on Danfoss valves.

The arrangement of the suitable adapter ring for the appropriate valve can be found in the following description. Please completely remove the connection rods