Extron V-Lock Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Extron V-Lock (8 pagina's) in de categorie luidsprekersteun. Deze handleiding was nuttig voor 8 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
User’s Guide
Replacement accessory for Extron System INTEGRATOR®
SI 3 Surface Mount Speakers
68-1490-01
Rev. A
03 08
V-Lock Wall Mount Assembly Kit
V-Lock Wall Mount Assembly Kit • Introduction
Introduction
1
Figure 1 — V-Lock Assembly packaging details
Packaging Information
The V-Lock Assembly Kit contains two individually packed
wall mount assemblies (one for each speaker) and an Allen hex
tool.
Allen Hex Tool
Wall Mount
Assemblies
Outer
Packaging
About the V-Lock Assembly Kit
The V-Lock Wall Mount Assembly Kit is a pair of replacement
wall mount assemblies (wall plate and V-lock groove only) for
the Extron System INTEGRATOR® SI 3 surface mount speakers.
V Lock
Groove
(Stage)
Hex Lock
Screw
Pivot
Ball
Wall
Plate
Wi ngri
Access
Hole
Secondary
Mounting
Holes (4)
Primary
Mounting
Holes (2)
Figure 2 — Main parts of the V-Lock Assembly Kit
V-Lock Wall Mount Assembly Kit • Installation
Installation
2
Installing the V-Lock Assembly Kit
If your speakers are not already installed, follow the instructions
outlined in the supplied with the speakers (or SI 3 User's Guide
online at www.extron.com).
If your speakers are already installed, replace the V-Lock
assembly by following the instructions, below.
N Referring to packaging information for location,
carefully remove and check contents before installation.
N Extron recommends that the wiring installation is
performed by a professional audio equipment installer.
N For speaker details, specifications, troubleshooting tips,
and service access information, refer to the
SI 3 User's Guide supplied with the speakers, or online
at www.extron.com.
Existing wall mounting application
To replace a damaged V-Lock assembly that is already installed,
do the following:
1. Remove the Extron logo from the front of the speaker to
access the hex cap screw. Retain the logo.
2. Insert the hex tool and unlock the speaker.
3. Carefully lift the speakers away from the bracket, then
disconnect the seismic cable and audio wires from the rear
of the speakers.
To remo (or insert) the wires,ve
push down on the spring terminals
at the back of the speaker.
Release the springs to secure.
INPUT
Positive Wire
Negative
Wire
Figure 3 — Remove audio wires from the terminals
N If the ends of the wires are damaged and need to be
re-stripped, follow the instructions in the S I 3 User's
Guide.


Product specificaties

Merk: Extron
Categorie: luidsprekersteun
Model: V-Lock

Heb je hulp nodig?

Als je hulp nodig hebt met Extron V-Lock stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding luidsprekersteun Extron

Extron

Extron V-Lock Handleiding

6 September 2024

Handleiding luidsprekersteun

Nieuwste handleidingen voor luidsprekersteun

Sanus

Sanus BSWM3IWP Handleiding

5 September 2024
Sanus

Sanus WSWM3IWP Handleiding

5 September 2024
Valcom

Valcom V-9915M Handleiding

5 September 2024
Valcom

Valcom V-9912M Handleiding

5 September 2024
Valcom

Valcom V-9910 Handleiding

5 September 2024
Valcom

Valcom V-9904M-5 Handleiding

5 September 2024
Valcom

Valcom V-9806 Handleiding

5 September 2024
Valcom

Valcom V-936480 Handleiding

5 September 2024
Valcom

Valcom V-9805 Handleiding

5 September 2024