Extron TLP Pro 1725MG Handleiding

Extron Monitor TLP Pro 1725MG

Lees hieronder de šŸ“– handleiding in het Nederlandse voor Extron TLP Pro 1725MG (6 pagina's) in de categorie Monitor. Deze handleiding was nuttig voor 9 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/6
1
IMPORTANT:
Go to for the
complete user guide and installation
instructions before connecting the
product to the power source.
www.extron.com
TLP Pro 1225MG, 1525MG, and 1725MG ā€¢ Setup Guide
Overview
The ExtronĀ® TLP Pro 1225MG, TLP Pro 1525MG, and TLP Pro 1725MG are wall-mounted touchpanels with capacitive, edge-to-edge
glass touchscreens. The TLP Pro 1225MG has a 12.1 inch screen with a 1280x800 resolution. The TLP Pro 1525MG has a 15.6 inch
screen with a 1366x768 resolution. The TLP Pro 1725MG has a 17.3 inch screen with a 1920x1080 resolution. All three touchpanels
are ideal for any AV applications requiring large touchpanels with ī˜Ÿexible mounting options and fully customizable interfaces. This
guide provides instructions for experienced installers to mount and install these touchpanels. For more complete details, see the
TLPī˜ŸPro 1225, 1525, and 1725 Series User Guide at www.extron.com.
Setup Checklist
Get Ready
īš…Download and install the latest version of the following software:
īš…GUI Designer ā€” Used to design layouts for Extron TouchLinkĀ® Pro touchpanels and third party touch interfaces.
īš…Global ConfiguratorĀ® Plus and Professional ā€” Used to set up and conī˜žgure the control processor and touchpanel.
īš…Global ScripterĀ® ā€” Used to rovide an integrated development environment for Extron control systems programming.
Global Scripter provides an Extron-exclusive Pythonā„¢ library (ControlScriptĀ®) and modules to get you started.
īš…Toolbelt ā€” Used for device discovery, device information, ī˜žrmware updates, and conī˜žguration of network settings, system
utilities, and user management for TouchLink Pro devices.
NOTE: All four software programs are available from www.extron.com.
īš…Obtain the following network information from your network administrator:
īš…DHCP status (on or off). If DHCP is off, you also require:
īš…IP address īš…Subnet mask īš…Gateway
īš…Username ā€” This can be either or .
īš…Passwords ā€” The factory conī˜žgured passwords for all accounts on this device have been set to the device serial number.
Passwords can be changed during conī˜žguration. Passwords are case sensitive.
NOTE: If the device is reset to default settings, the passwords are reset to the default password, which is (for
either or ).
īš…Make a note of the touchpanel MAC address from the label on the back of the device.
Mount and Cable All Devices
ATTENTION:
ā€¢ Do not power on the touchpanels until you have read the Attention in the ā€œPower Supplyā€ section of the
TLPī˜ŸPro 1225, 1525, and 1725 Series User Guide.
ā€¢ Ne branchez pas les Ć©crans tactiles avant dā€™avoir lu la mise en garde dans la section Ā«ī˜sources dā€™alimentationī˜Ā» du TLPī˜ŸPro
1225, 1525, and 1725 Series User Guide.
īš…Mount the units. There are several mounting options for TouchLink Pro touchpanels (see on page 2). Mounting
īš…Connect cables to the touchpanels (see on page 4).Rear Panel Features
īš…Connect the touchpanel to a Power over Ethernet (PoE) injector. The TLP Pro 1725MG ships with the PI 140 power injector.
A power injector must be purchased separately for the 12-inch and 15-inch models.
īš…Connect an Extron IP LinkĀ® Pro control processor to the same Ethernet subnetwork as the touchpanel.
Set up the Touchpanels for Network Communication
īš…Connect the PC that you will use for setup, the control processor, and touchpanel .to the same Ethernet subnetwork
īš…Use the (see page 6) or Toolbelt (see Setup Menu Toolbelt Help File) to set the DHCP status and, if necessary, the IP
address, subnet mask, gateway, and related settings for the touchpanel.
Conļ¬gure the Touchpanels
īš…Create a graphical user interface with GUI Designer (see for step-by-step instructions).GUI Designer Help File
īš…Associate functions with the graphical user interface features by conī˜žguring (see the ) or Global Conļ¬gurator Help File
programming (see the ) the system.Global Scripter Help File
2
TLP Pro 1225MG, 1525MG, and 1725MG ā€¢ Setup Guide
Mounting
ATTENTION:
ā€¢ Do not install the TLP Pro 1225MG, TLP Pro 1525MG, or TLP Pro 1725MG in a ī˜žre resistant rated wall or partition
assembly.
ā€¢ Ne pas installer le TLP Pro 1225MG, le TLP Pro 1525MG, ou le TLP Pro 1725MG dans un mur rĆ©sistant au feu ou une
cloison.
ā€¢ All structural steps and electrical installation must be performed by qualiī˜žed personnel in accordance with local and
national building codes and electrical codes.
ā€¢ Toute Ć©tape structurelle et installation Ć©lectrique, doit ĆŖtre effectuĆ©e par un personnel qualiī˜žĆ©, conformĆ©ment aux codes du
bĆ¢timent, aux codes incendie et sĆ©curitĆ©, et aux codes Ć©lectriques, locaux et nationaux.
Wall Mounting
The touchpanels can be wall mounted using the provided hardware. Where local codes require a rear metal enclosure, either model
can be mounted using the Extron BB 700M (not provided). Figure 1 shows the TLP Pro 1525MG. Mount the TLP Pro 1225MG or
TLP Pro 1725MG in the same way.
With a wall box
Some local building codes require the touchpanel to be mounted in a wall box such as the Extron BB 700M. This installation
procedure is described below.
1. Cut a hole in the drywall, 9.6 inches (243 mm) wide
x 6.6 inches (166 mm) high, and install the
Install the BB 700M (optional).
TLP Pro 1525MG
Back View
Hold the touchpanel at a slight angle
Mount the touchpanel over the two
hooks on the mounting plate.
Add the mounting plate. Align with
the wall box and mark holes for screws.
Secure the mounting plate
to the wall with screws (4).
Place the provided mounting sc ws (2)re
with washers in the mounting sc w slotre
in the touchpanel.
6
5
3
1
2
4
7
Secu the touchpanel by tightening there
mounting sc ws against the base of the re
mounting plate.
BB 700M (see ī˜žgure 1, 1), as described
in the (see BB 700M Installation Guide
www.extron.com).
2. Place the metal mounting plate
against the wall, mark the four
mounting holes, and drill four pilot
holes (2) in those locations.
3. Secure the mounting plate with four
#10 screws (3).
4. Run and connect cables to the back
of the touchpanel (4, and see Rear
Panel Features on page 4).
5. Insert the two provided Phillips pan
head #6-32 x Ā¾ inch length screws
with washers in the mounting screw
slot (5, see ī˜žgure 1, Back View
inset). Leave a gap for the ī˜Ÿange at the
bottom of the mounting plate to ī˜žt into.
6. Hold the touchpanel at a slight angle
and lower the notches at the top of
the back panel over the hooks of the
mounting plate (6).
7. Swing the bottom of the touchpanel
inwards so that it lies ī˜Ÿat against the
mounting plate with the ī˜Ÿange at the bottom
of the mounting plate sitting in a groove in the
bottom of the touchpanel.
8. Secure the touchpanel to the mounting plate with the
mounting screws (7).
Without a wall box
If the wall box is not required by local building codes, you can
mount the touchpanel directly into drywall.
1. Download the cut-out template for your touchpanel from Figure 1. TLP Pro 1525MG Mounting
www.extron.com. Print it at 100% (no scaling).
2. Use the template to mark the wall, cut the hole, and drill the four pilot holes. The size of the cut-out hole is 9.25 inches (235 mm)
wide x 6.25 inches (159 mm) high.
3. Secure the mounting plate and complete the installation, as described in steps 3 through 8 above.
3
Product Category
Rack Mounting
These touchpanels can be mounted in any standard 19-inch equipment rack, using the optional rack mounting kit. The
TLP Pro 1225MG can be mounted with the RM2 mounting kit. The TLP Pro 1525MG and the TLP Pro 1725MG can be mounted in
the RM3 mounting kit. Read the ā€œUnderwriters Labs Guidelines for Rack Mountingā€ section of the TLPī˜ŸPro 1225, 1525, and 1725
Series User Guide and follow the instructions provided with the appropriate kit.
Front Panel Features
Figure 2 shows the TLP Pro 1225MG front panel. The TLP Pro 1525MG and TLP Pro 1725MG features are very similar.
A B
C
D D
E F
Figure 2. TLP Pro 1225MG Front Panel
A ā€” Monitors ambient light level and adjusts screen brightness.Ambient light sensor
B ā€” Can be programmed to provide system feedback. This LED light bar is located above the screen.Status light
C ā€” Provides simple control of AV systems.Capacitive touch screen
zThe TLP Pro 1225MG has a 12.1 inch screen with a 1280x800 resolution.
zThe TLP Pro 1525MG has a 15.6 inch screen with a 1366x768 resolution.
zThe TLP Pro 1725MG has a 17.3 inch screen with a 1920x1080 resolution.
D ā€” Provide stereo audio for video preview and audible feedback from button presses. They are located below the Speakers
screen, one on each side of the panel.
E ā€” Detects motion between three to ī˜žve feet from the touchpanel, and at least 15Ā° from the center axis.Motion sensor
zIf the sleep timer feature has been set, and no motion has been detected for a user-deī˜žned period of time, the touchpanel
enters sleep mode.
zIf the wake on motion feature has been set, and motion is detected by the sensor while the screen is in sleep mode, the
screen display is restored and active.
For more information about setting the Sleep Timer Wake on Motion or , see the ā€œSetup Menuā€ section of the TLPī˜ŸPro 1225,
1525, and 1725 Series User Guide.
F ā€” Activates the setup menu (see ). Access the button from under the touchpanel. It performs the Menu button Setup Menu
same function as the rear panel Menu button but is easier to reach when the touchpanel is installed.


Product specificaties

Merk: Extron
Categorie: Monitor
Model: TLP Pro 1725MG

Heb je hulp nodig?

Als je hulp nodig hebt met Extron TLP Pro 1725MG stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Monitor Extron

Handleiding Monitor

Nieuwste handleidingen voor Monitor