Extron MDA 5A RCA Handleiding

Extron Receiver MDA 5A RCA

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron MDA 5A RCA (2 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 51 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

Setup Guide — MDA 5V, 5SV, 5A RCA

The Extron® MDA 5 series of mini distribution ampliﬁers distribute buffered

composite video (MDA 5V), buffered S-video (MDA 5SV), and ampliﬁed stereo audio

(MDA 5A RCA). Unless otherwise stated, these instructions apply to all three of the

ampliﬁers.

W These instructions provide a quick setup guide for experienced installers.

Installation and service must be performed by authorized personnel only.

MDA 5V

POWER

12V

.5A MAX

INPUT

IN HIGH Z

75 Ohm

LOOP 2

OUTPUTS

2 4 6

Rear Panel MDA 5V

DISTRIBUTION AMPLIFIER

Front Panel All Models

MDA 5SV

POWER

12V

.5A MAX

INPUT

IN HIGH Z

75 Ohm

LOOP 2

OUTPUTS

Rear Panel MDA 5SV

MDA 5A RCA

POWER

12V

.34A MAX

INPUT OUTPUTS

1 2 3 4 5

582

Rear Panel MDA 5A RCA

Step 1

Turn all the equipment off and disconnect all cables.

Step 2

Mount the unit in a convenient location, in a rack, under a desk, or on a projector mounting system. Follow the

instructions included with the appropriate mounting kit.

Step 3

Connect the external 12 VDC power supply (provided) to the 2-pole, captive screw power

connector (b). When power is applied to the unit, the front panel LED (

a) lights green.

C Voltage polarity is important. Identify the negative lead by the ridges on the side (see ﬁgure

at right).

C Always use a power supply speciﬁed by Extron for this unit. Use of an unauthorized power

supply voids all regulatory compliance certiﬁcation and may cause damage to the supply

and the distribution ampliﬁer.

Step 4

For the MDA 5V:

Connect a video source to the video input (c), using composite video (BNC) connectors.

For the MDA 5SV:

Connect a video source to the video input (c), using S-video (4-pin mini DIN) connectors.

For the MDA 5A RCA:

Connect an audio source to the audio inputs (c), using unbalanced stereo to RCA connectors. Left channel input goes to

the upper input; right channel input goes to the lower input.

Indicators and

Connectors

a

Power LED

b

Power supply input

c

Video input

d

Video loop to local

monitor

e

Audio input (left channel

top; right channel

bottom)

f

High Z/75 Ohm switch

g

video outputs

h

audio outputs (left

channel top; right

channel bottom)

POWER

12V

.5A MAX

SECTION A–A

RidgesSmooth

Power Supply

Output Cord

A A

Extron USA - West

Headquarters

+800.633.9876

Inside USA / Canada Only

+1.714.491.1500

+1.714.491.1517 FAX

Extron USA - East

+800.633.9876

Inside USA / Canada Only

+1.919.863.1794

+1.919.863.1797 FAX

Extron Europe

+800.3987.6673

Inside Europe Only

+31.33.453.4040

+31.33.453.4050 FAX

Extron Asia

+800.7339.8766

Inside Asia Only

+65.6383.4400

+65.6383.4664 FAX

Extron Japan

+81.3.3511.7655

+81.3.3511.7656 FAX

Extron China

+400.883.1568

Inside China Only

+86.21.3760.1568

+86.21.3760.1566 FAX

Extron Middle East

+971.4.2991800

+971.4.2991880 FAX

Setup Guide — MDA 5V, 5SV, 5A RCA, cont’d

575 Ohm

HIGH Z

LOO P

2 4

1 3

12V

POW ER

.1A MAX

MDA 5S V

INP UT OU T PU T S

Local Monitor

Flat Panel

Display

Flat Panel

Display

VCR

Ext ron

MDA 5SV

Distribution

Amplier

Step 5 (optional)

For the MDA 5V:

Connect the video loop feed (d) to a local monitor, using composite video connectors.

For the MDA 5SV:

Connect a video loop feed (d) to a local monitor, using S-video connectors.

Step 6

For the MDA 5V and MDA 5SV models:

If a terminated device was connected to the loop feed in , set the High Z/75 Ohm switch (step 5 f) to High Z (up

position, as shown in the ﬁgure at right). If no device or an unterminated device was connected to the loop feed

in , set the switch to 75 Ohm (down position).step 5

Step 7

For the MDA 5V:

Connect up to ﬁve display composite video devices to the outputs (g), using composite video connectors.

For the MDA 5SV:

Connect up to ﬁve display S-video devices to the outputs (g), using S-video connectors.

For the MDA 5A RCA:

Connect up to ﬁve stereo audio devices to the audio outputs (h), using the RCA connectors (left channel top; right channel

bottom).

Troubleshooting

If you have problems, please consult the full manual, which is available on-line at www.extron.com.

If the problems persist, contact the Extron service department.

MDA 5A RCA

P O WER

12V

.3A MAX

INPUT OUT PUT S

321 4 5

CD Player

Tape Recorder

Ext ron

MDA 5A RCA

Distribution

Amplier

Ext ron

XPA 1002

Power

Amplier

Ext ron

XPA 1002

Power

Amplier

Ext ron

SI 28

Surface-mount

Speakers

Ext ron

SI 28

Surface-mount

Speakers

XPA 1002

1 2LIMITER/PROTECT

SIGNAL

OVER

TEMP

XPA 1002

LIMITER/PROTECT

SIGNAL

OVER

TEMP

HIGH Z

75 Ohm

68-614-50

Rev. A

01 10

Product specificaties

Merk:	Extron
Categorie:	Receiver
Model:	MDA 5A RCA
Gewicht:	200 g
Breedte:	110 mm
Diepte:	76 mm
Hoogte:	42 mm
Gewicht verpakking:	1000 g
Stroom:	1 A
Certificering:	CE, C-tick, FCC Class A, ICES, VCCI
Formaat analoog signaal:	NTSC 3.58, NTSC 4.43, PAL, SECAM
Ingangsspanning:	100-240 V
Temperatuur bij opslag:	-40 - 70 °C
Luchtvochtigheid bij opslag:	10 - 90 procent
Rack-montage:	Ja
Veiligheid:	CE, c-UL, UL
Bandbreedte:	400 MHz
AC-ingangsfrequentie:	50 - 60 Hz
Stroomverbruik (typisch):	12 W
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	10 - 90 procent