Extron DTP R HWP 4K 331 D Handleiding

Extron Receiver DTP R HWP 4K 331 D

Lees hieronder de 📖 handleiding in het Nederlandse voor Extron DTP R HWP 4K 331 D (4 pagina's) in de categorie Receiver. Deze handleiding was nuttig voor 2 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
IMPORTANT:
Go to www.extron.com for the complete
user guide, installation instructions, and
specifications before connecting the
product to the power source.
1
DTP R HWP 4K D Series • Setup Guide
This setup guide provides instructions for an experienced installer to set up and operate the Extron DTP R HWP 4K 231 D and
DTP R HWP 4K 331 D extenders.
Installation
Step 1 — Disconnect Power
Disconnect all equipment power sources.
Step 2 — Prepare the Mounting Surface
ATTENTION:
Installation and service must be performed by authorized personnel.
Linstallation et l’entretien doivent être effectués par le personnel autorisé uniquement.
The unit must be installed in accordance with the National Electrical Code and with local electrical and safety
codes.
Lunité doit être installée conformément au National Electric Code et aux normes électriques et de sécurité locales.
NOTE: Use the included mud ring (MR 200) or a UL approved 1-gang RACO wall box (not supplied) with a depth of at
least 3.0 inches (7.6 cm). For more information, see the full product user guide at www.extron.com.
a. Place either the mud ring (see gure on page 1) or the wall box (see gure on page 2) against the installation surface and
mark the opening guidelines.
TIP: Use a level to mark the opening.
b. Cut out the material from the marked area.
c. Either:
Insert the mud ring into the opening, rotate the locking
arms, and secure it with the supplied screws,
or
Secure the wall box to the wall stud with 10-penny nails
or #8 or #10 screws, leaving the front edge ush with the
surface.
TLP T1000
V
IN1608
100-240V ~ -- A MAX
1
2
CONFIGURABLE
HDMI HDMI
5
6
7 8
C
RS-232 IR
RS-232 IR
TxRx Tx RxG
TxRx Tx RxG TxRx T x RxG
HDMI
A
B
3
4
INPUTS OUTPUT S
Tx Rx
RS-2 32
G
LAN
2x25W(8Ω)/2x50W(4Ω)
RESET
AUDIO INPUT S OUTPUT S
REMOT E
L L1 R R
L 2 R
L
3
R
CLASS 2 WIRING
L 4 R
L 5 R
+48V
+48V
1 2
L R
VARIABLE
IN1608 S A
2
MIC/LINE
L 6 R
SIG LINK
DT N
SIG LINK
D IN
SIG LINK
DTP UT
50/60 Hz
RS-232 IR
OVER DTP
OVER DTP
OVER DTP
AMPLIFIED OUT PUT
VOLUME
SCALING PRESENTATION SWITCHER
IN 16 08
INPUTS
1
HDCP
SIGNAL
OUTPUTS
ENTER
MENU
Ext r on
2 3 4 5 6 7 8 A B C
IN PUTS
12345678
CONFIG
Extron
DTP T UWP 2 D23
Transmitter
Extron
DTP T HWP 2 D23
Transmitter
Extron
DTP R P HW 4K 331 D
Receiver
Ethe etrn
XTP eDTP 24 Cabl
230'
AUTO SW
CONFIG
IR OUT
HDMI IN
AUDIO IN
S
G
HDCP
1
AUDIO IN
VGA IN
AUTO S W
CONFIG
IR OUT
HDMI IN
AUDIO IN
S
G
HDCP
1
HDMI IN
AUDIO IN
HDCP
1
2
HDMI OUT
GT x Rx
Tx Rx
OVER DTP
RS-232 IR
Projector
HDMI
I O 0PCP PR 55
21
LIMIT
RIR
Tx
Rx
Tx
Rx
RTS
CTS
COM
IR/SERIAL RELAYS FLEX
I/O
S LIMIT
eBUSSWITCHED
12 VDC
1000
LINK
ACT
IPCP PRO 550
OVER
43 1 2 3 4 5 6 7 8
OVER
5678
21
3 4
213 4
5678
21 3 4
Rotate locking arm
and insert into llwa
opening.
Mud Ring
2
DTP R HWP D 4K Series • Setup Guide (Continued)
d. Run all required cables (see steps , , and ),3 4 5
thread the cables through the mud ring or walll
box, and secure them with cable clamps.
TIP: In order to t the unit in the junction
box, do not install boots on TP cables
and RJ-45 connectors.
Step 3 — Run Cables Between Units
Connect the rear panel transmitter output to a rear panel receiver input using twisted pair cable.
Wire the cable as shown in the diagram to the right.
For optimal performance, Extron highly recommends the following:
RJ-45 termination with shielded twisted pair cable must comply with TIA/EIA-T568B
wiring standard for all connections. For more information on TP cable wiring and
termination, see the at DTP R HWP 4K 231 and 331 D User Guide www.extron.com.
Use shielded twisted pair cable, 24 AWG solid conductor or better, with a minimum cable
bandwidth of 400 MHz.
ATTENTION:
Do not use Extron UTP23SF-4 Enhanced Skew-Free AV UTP cable to link the device with DTP transmitters or
receivers.
N’utilisez pas le câble AV Skew-FreeUTP version améliorée UTP23SF d’Extron ou le câble STP201 pour relier
le appareil avec les émetteurs ou les récepteurs DTP.
NOTE: Extron XTP DTP 24 Shielded twisted pair cable is strongly recommended for
optimal performance.
Use shielded RJ-45 plugs to terminate the cable.
Limit the use of RJ-45 patches. Overall transmission distance capabilities vary
depending on the number of patches used. If possible, limit the number of patches to
two total.
If RJ-45 patches must be used in the system, shielded patches are recommended.
Step 4 — Connect Output Device
Front Panel
A DTP RS-232 and IR connectors — To pass serial or infrared data or control signals,
such as serial control of a projector, connect the host device to the transmitter and the
peripheral device to the receiver via the RS-232 and IR captive screw connectors on
both units.
B HDMI output connector Connect an HDMI cable between this port and the input on
a sink device.
HDMI OUT
Extron
OVER DTP
A
B
DTP R HWP 4K 231 D
and DTP R HWP 4K 331 D
Front Panel
5
Pin
1
2
3
6
7
8
4
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA
T568-B
TP Wires
1 8234567
Pins:
Wall Stud
Screws
or Nails
Signal
Output
Cabl
e
Decorator-Style Faceplate
Extron
DTP R HWP 4K 231 D
HDMI OUT
Ext ron
OVER D TP
3
DTP R HWP D 4K Series • Setup Guide (Continued)
Rear Panel
A DC power input connector — Wire and plug the included external 12 VDC power supply into either this 2-pole
connector or the power input connector on the transmitter (see the at DTP R HWP 4K 231 and 331 D User Guide
www.extron.com for wiring information).
B DTP IN connector — Connect the opposite end of the twisted pair cable from the
transmitter output connector to this RJ-45 connector.
ATTENTION:
Do not connect these outputs to a telecommunications or computer
data network.
Ne connectez pas ces appareils à des données informatiques ou à un
réseau de télécommunications.
NOTES:
The DTP R HWP 4K 231 D models can receive video, control, and audio (if
applicable) signals up to 230 feet (70 meters).
The DTP R HWP 4K 331 D models can receive video, control, and audio (if
applicable) signals up to 330 feet (100 meters).
Signal LED — Lights when the unit is receiving any valid signal on the DTP In connector.
Link LED — Link is established between the units on the DTP cable.
C Audio Output connector — Connect a balanced or unbalanced stereo or mono audio device to the receiver via the
Audio captive screw connector. See the drawing below.
Tip
Ring
Sleeve (s)
Tip
Ring
Tip
Sleeve (s
)
Tip
See Caution
See Caution
L R
L R
Unbalanced Balanced
CAUTION: For unbalanced audio, connect the sleeves to the ground contact. DO NOT connect the sleeves to the
negative (–) contacts.
ATTENTION : Pour l’audio asymétrique, connectez les manchons au contact au sol. Ne PAS connecter les
manchons aux contacts négatifs (–).
Step 5 — Power the Units
The units can be powered one of two ways:
Locally with the included power supply. A compatible transmitter can then be powered remotely through the DTP line.
Remotely via the DTP line by a locally powered DTP transmitter.
NOTE: See the at DTP R HWP 4K 231 and 331 D User Guide www.extron.com for wiring information.
Step 6 — Final Installation
a. Make all connections, power the units, and test the system for satisfactory operation.
b. At the power outlet, unplug the power supply.
c. Mount the receiver into the wall box, and attach the supplied decorator-style faceplate to the unit.
d. At the power outlet, reconnect the power supply to power up both units.
SIG LINK
DTP IN
AUDIO
POWER
12V
A MAX
L R
1
DTP IN
DTP R HWP 4K 231 D
A
BC
DTP R HWP 4K 231 D
and DTP R HWP 4K 331 D
Rear Panel


Product specificaties

Merk: Extron
Categorie: Receiver
Model: DTP R HWP 4K 331 D

Heb je hulp nodig?

Als je hulp nodig hebt met Extron DTP R HWP 4K 331 D stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Receiver Extron

Handleiding Receiver

Nieuwste handleidingen voor Receiver