Extech 461825 Handleiding
Extech
Kilometerteller
461825
Lees hieronder de 📖 handleiding in het Nederlandse voor Extech 461825 (4 pagina's) in de categorie Kilometerteller. Deze handleiding was nuttig voor 57 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/4
USER GUIDE
Combination Photo-Tachometer
Stroboscope
Model 461825
2 461825-EU-EN v1.6 10/13
Introduction
Congratulations on your purchase of Extech’s Combination Photo-Tachometer/Stroboscope. This
device is shipped fully tested and calibrated and, with proper use, will provide years of reliable service.
Please visit our website (www.extech.com) to check for the latest version of this User Guide, Product
Updates, and Customer Support.
Meter Description
1. Tachometer Light Source
2. LCD Display
3. Measure trigger button
4. Memory Recall button
5. FINE adjust knob
6. COARSE adjust knob
7. Range/Function select switch
8. Stroboscope flash tube
Note: Battery compartment is on rear of meter
You, as the end user, are legally bound (EU Battery ordinance) to return all used
batteries, disposal in the household garbage is prohibited! You can hand over your
used batteries / accumulators at collection points in your community or wherever batteries
/ accumulators are sold!
Disposal: Follow the valid legal stipulations in respect of the disposal of the device at the
end of its lifecycle
1
2
4
3
56
8
7
3 461825-EU-EN v1.6 10/13
Operation
STROBOSCOPE MEASUREMENT PROCEDURE
Select the Stroboscope Function and Range using the Range/Function Select Switch. The switch
has four positions, three of which are stroboscope-dedicated with white range numbers. The fourth
position is Photo-Tachometer dedicated and is labeled as such.
Speed Measurements.
1. Remove power to the moving object under test and affix a target mark on the area to be
measured.
2. Apply power to the moving object and press the stroboscope's Measure Trigger Button.
3. Aim the Stroboscope light beam toward the marked area on the object under test.
4. Use the FINE and COARSE adjust knobs to synchronize or "stop" the motion of the object's
mark. A single stationary image of the mark provides actual speed measurement data.
NOTE: Care must be taken to ensure that the mark is providing a 1:1 measurement. This is done
by checking that there is only one mark and not two, four, or more stationary marks on the object
under test. Two or more stopped marks indicate "harmonic" measurements (2:1, 3:1, 4;1 etc.)
which provide a doubling, tripling, or quadrupling of the actual speed. A useful method of avoiding
harmonic measurements is to adjust the FINE/COARSE knobs until two images (marks) appear
and then lower the flash rate (via COARSE/FINE knobs) until a single, stationary image appears.
This is the actual speed.
Inspecting a moving object
Measure the speed of a moving object as described above and move the FINE adjust knob
alternately higher and lower to visually inspect all areas of the device.
PHOTO-TACHOMETER MEASUREMENT PROCEDURE
1. Select the Photo-Tachometer function by moving the Range/Function select switch to the
PHOTO position.
2. Affix a small piece (approx. 0.5") of supplied reflective tape to the object under test.
3. Press the meter's Measurement Trigger button and align the Photo-Tachometer light
source with the reflective tape mark on the moving object.
4. Wait until the Monitor Indicator appears in the upper left hand corner of the LCD
indicating that synchronization has occurred.
5. Release the Measure Trigger button only after the reading has stabilized (approx. 2
seconds).
NOTE: To obtain better accuracy for low RPM measurements (less than 50 RPM) use more than
one piece of reflective tape. Divide the meter reading by the number of reflective tape pieces for
accurate measurement data.
Product specificaties
| Merk: | Extech |
| Categorie: | Kilometerteller |
| Model: | 461825 |
Heb je hulp nodig?
Als je hulp nodig hebt met Extech 461825 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Kilometerteller Extech
1 Mei 2023
25 April 2023
21 April 2023
6 April 2023
5 April 2023
30 Maart 2023
25 Maart 2023
11 Maart 2023
10 Maart 2023
22 Februari 2023
Handleiding Kilometerteller
- Kilometerteller Beha-Amprobe
- Kilometerteller PCE Instruments
- Kilometerteller Pyle
- Kilometerteller Uni-T
- Kilometerteller Velleman
- Kilometerteller Voltcraft
- Kilometerteller Wachendorff
- Kilometerteller Testo
- Kilometerteller Emko
- Kilometerteller MGL Avionics
- Kilometerteller Chauvin Arnoux
- Kilometerteller Aerospace Logic
- Kilometerteller Electronics International
Nieuwste handleidingen voor Kilometerteller
17 November 2024
17 November 2024
6 Maart 2024
6 Maart 2024
6 Maart 2024
5 Maart 2024
27 November 2023
13 September 2023
13 September 2023
13 September 2023