Exakt DC-270 Handleiding
Lees hieronder de 📖 handleiding in het Nederlandse voor Exakt DC-270 (32 pagina's) in de categorie Zaag. Deze handleiding was nuttig voor 59 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/32
EXAKT DC-270
1 – 4, Diagrams 29. Original instructions
5 – 9, Abbildungen 29. Übersetzung der originalen Gebrauchsanweisung
10 – 14, Diagrammes 29. Traduction des instructions d’origine
15 – 19, Diagramas 29. Traducción de las instrucciones originales
20– 23, Figura 29. Traduzione delle istruzioni originali
24 – 28, Afbeelding 29. Vertaling van de originele instructies
EXAKT Precision Tools Ltd.
Midmill Business Park
Tumulus Way
Kintore, AB51 0TG
United Kingdom
Designation: DC is a Deep Cut Saw
Tel: + 44 (0) 1467 633 800
0800 180 7063 (D)
0800 916 696 (F)
800 930 019 (I)
Fax: + 44 (0) 1467 633 900
E-mail: info@exaktpt.com
Web: www.exakt.eu
Patents Apply
Registered Design
® Registered Trade Mark
Made in PRC
480144-2
1  EXAKT Precision Tools Ltd. 2010
1  EXAKT Precision Tools Ltd. 2010
English
Warning Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future
reference.
DC-270 Safety Warnings –
Instructions for Putting Into Use
Setting up the Saw for Use
After unpacking check that there are no parts missing or
damaged. If there are contact supplier and do not operate.
Before using a blade needs to be fitted as described in the
operating instructions. (See Blade Changing Section)
Information on Power Supply
This equipment should be connected to a normal domestic
socket outlet with a voltage rating between 210 and 250 V
and a current rating of between 13 and 16A.
Illustrated Description of Functions
See foldout page A
1. Switch
15. Brush cover
2. Locking buton
16. Dust extract nozzle
3. Main handle
17. Spindle lock button
4. Auxiliary handle
18. Parallel fence slot
5. Guard lock button
19. Blade screw
6. Depth setting knob
20. Blade changing key
7. Depth of cut guage
21. Blade washer
8. Guard release knob
22. Blade rotation indicator
9. Fence locking knob
23. Fixed guard
10. Parallel fence
24. Auxiliary handle mounts
11. Blade guide pointer
25. Inner flange
12. Blade
26. TCT blade
13. Blade guard
27. Diamond blade
14. Motor housing
28. Dust hose adaptor
List of contents
EXAKT DC 170 Saw
Torx key
Blades (dependant on kit)
Spare safety washer
Auxiliary handle
Dust hose adaptor
Instruction manual
Storage case
DC-270 Safety Warnings – Operating Instructions
This tool performs best when attached to a suitable
vacuum cleaner/dust extractor.
Setting the Cutting Depth
1. The depth of cut can be set in millimetres. To adjust,
loosen the Depth setting knob, slide to the desired
position and tighten. (Diagram A)
2. When cutting wood the depth of cut should be set to
slightly greater than the thickness of the material for best
results.
3. When cutting plastics the depth of cut should be set to
slightly greater than the thickness of the material. If
melting occurs a greater depth setting will improve
results.
4. When cutting metals the depth of cut should be set to
approximately 1.0 mm greater than the material
thickness for best results.
If it is desirable not to mark the surface beneath the
workpiece, the depth can be set to the same as the
material thickness, when cutting wood or plastics, but this
may result in a rough edge.
NB. If the depth control knob becomes difficult to turn,
unscrew it until the rubber seal can be seen. Clean the
surrounding area with a soft brush and then apply a
very small quantity of synthetic grease to the seal.
Blade Changing
NB. Incorrect positioning of the blade can permanently
damage the tool.
1. Ensure the tool is unplugged from the mains supply.
2. Pull guard release knob to open guard (Diagram B )
3. Press spindle lock button (Diagram C)
4. Unscrew blade using torx key
5. Place the new blade onto the blade shaft ensuring the
hole locates correctly and the teeth point forwards in the
direction of the curved arrow. (Diagram D)
6. Replace the safety retaining washer and tighten the
screw.
7. Close the guard before plugging in.
Clamping
It is not normally necessary to clamp the material being cut
as long as it is fully supported on a work surface and held
with one hand. Clamping should be used where:
ï‚· The operator is inexperienced in the use of power
saws or weak handed
ï‚· Small parts or tough material is to be cut
Product specificaties
| Merk: | Exakt |
| Categorie: | Zaag |
| Model: | DC-270 |
Heb je hulp nodig?
Als je hulp nodig hebt met Exakt DC-270 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Zaag Exakt
31 Augustus 2023
Handleiding Zaag
- Zaag Bosch
- Zaag Panasonic
- Zaag AEG
- Zaag DeWalt
- Zaag Batavia
- Zaag Dual Saw
- Zaag Einhell
- Zaag Elektra Beckum
- Zaag Elu
- Zaag Ferm
- Zaag Ferrex
- Zaag Festool
- Zaag Fleurelle
- Zaag Fuxtec
- Zaag Gamma
- Zaag Hikoki
- Zaag Kinzo
- Zaag Kress
- Zaag Lux Tools
- Zaag Makita
- Zaag Metabo
- Zaag Parkside
- Zaag Powerplus
- Zaag Protool
- Zaag Ryobi
- Zaag Scheppach
- Zaag Skil
- Zaag Toledo
- Zaag Triton
- Zaag Varo
- Zaag Vonroc
- Zaag Workzone
- Zaag Proxxon
- Zaag Dexter Power
- Zaag Graule
- Zaag Mac Allister
- Zaag Toolson
Nieuwste handleidingen voor Zaag
13 Oktober 2023
13 Oktober 2023
13 Oktober 2023
13 Oktober 2023
13 Oktober 2023
25 September 2023
25 September 2023
11 September 2023
11 September 2023
5 September 2023