Eventide Blackhole Handleiding

Eventide Niet gecategoriseerd Blackhole

Lees hieronder de 📖 handleiding in het Nederlandse voor Eventide Blackhole (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 58 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/3
Blackhole Reference Guide for Firmware v1.0+| Eventide Part# 141328 Rev C
Eventide and Blackhole are registered trademarks of Eventide Inc. © 2020 Eventide Inc.
Device Manager Software
Available from Eventide’s website for Mac & PC
- Update Pedal Firmware - Backup/Restore entire device to a file
- Restore Factory Settings - Edit System Settings
- Import/Export Presets - View, edit, and organize Presets
Download: eventideaudio.com/edm
Restore Factory Settings: Boot pressing ACTIVE Footswitch & ACTIVE Button
Software Update: Boot pressing FREEZE Button & FREEZE Footswitch
Instructional Videos
eventideaudio.com/Blackhole-pedal
Technical Support
eventideaudio.com/support
Follow us on Social
Blackhole® Quick Reference Guide
Gravity
Turn Right - Normal decay
Turn Left - Inverse decay
Hi
Boost/Cut > 2,000 Hz
Mix
Dry/Wet Mix
Pre ets LE rD Ladde
Lo
Boost/Cut < 350 Hz
Size
Size of the imagined
reverb space
ACTIVE/BYPASS
Preset Mode: Load Preset
ACTIVE Button/LED
LED lit when ACTIVE
Press to toggle action of
ACTIVE Footswitch
LATCHING< >MOMENTARY
FREEZE Button/LED
LED OFF = Preset Increment
LED ON = FREEZE
(blinks when frozen)
Press & hold to Save Preset
FREEZE/Preset
Press & hold to toggle between
Preset Select & FREEZE On/Off
Button/LED
Toggles Primary/Secondary
Parameter Control
LED ON = Secondary
LED OFF = Primary
Feedback
Infinite decay
Freeze - dry signal passes as set by Mix
Presets - 5 On Board, 127 Via MIDI
NOTE ode mes out te seconds: Save M ti af r a few .
Pressing either Footswitch exits Save Mode.
Load Presets Save Presets
The currently loaded preset is indicated on the Preset LED Ladder. When a preset is modified the Preset LED
blinks once.
When a Preset is loaded or when toggling between Parameters using , Knob positions will not align with their
current Parameter values. As a result, turning a knob will likely cause an abrupt change in the sound.
With Catch Up ON, the sound does not change until the Knob is moved to the position corresponding to the
current value. The LED Ladder indicates whether the knob must be turned CCW (top LED blinks) or CW (bottom
LED blinks). The LED flashes more rapidly as the knob approaches the value set by the Preset. All five LEDs blink
once when the knob matches the stored Parameter value.
NOTE: To enable/disable Catch Up Knob Function, power up in System Setup mode and press FREEZE
Footswitch to toggle ON/OFF.
Catch Up Knob Function
To select and load a Preset using Footswitches:
1. FREEZE Footswitch selects Preset 1 to 5.
Preset 1 (top LED) to Preset 5 (bottom LED)
blinks.
2. ACTIVE Footswitch loads the Preset. LED stops
blinking.
To save one of the 5 Presets using the Buttons:
1. Press & hold FREEZE Button
- Blinking Ladder and Button LEDs let you know
you have entered Save Mode.
2. FREEZE Button selects Preset 1 to Preset 5.
3. ACTIVE Button saves Preset
- LEDs stop blinking to let you know the Preset
is saved.
NOTE: To select Preset, FREEZE Footswitch must be
in Preset mode. If FREEZE LED is lit, press and hold
FREEZE Footswitch.
S Exet p Pdl Jack
S et Bypass Mode
Toggles On or Off for each setting
Factory Default = Buffered
System Setup
Set M
IDI Channel
Set M
IDI Clock
ON
PRESS
Factory Default = Off
1 2 3 4 5... 16
PRESS
Set MIDI Channel: Click FREEZE Button
Default = Omni
BUFFER
RELAY
DSP+FX
KILL-DRY
PRESS
EXP (Default)
EXP AU + X
TRIPLE AUX
MIDI BOX
MIDI TRS
PRESS
Enter System Setup
To access these Global Settings, apply power while holding ACTIVE Footswitch and button.
Top two LEDs light when in System Setup. Changes are stored as they are made. Cycle power to exit System Setup.
[EXP+AUX]
TIP = Expression Pedal
RING = TAP TEMPO
[TRIPLE AUX]
TIP = Increment Preset
RING = Decrement Preset
Tip + RING = Load Preset
Note: Times out after a few seconds
Catch Up ON/OFF
ON
PRESS
Factory Default = Off
[MIDI BOX]
Receive and Send MIDI via a MIDI
Converter Box (Tip Active)
[MIDI TRS]
Receive MIDI directly with a DIN
to TRS or TRS cable.
20
Mix
Feedback
Gravity
Size
Lo
Hi
Depth
Rate
Out Lvl
21
22
23
24
25
26
27
28
N/A
Delay
Q
29
30
31
CC CCPRIMARY SECONDARY
NOTE: To use an Expression Pedal, the Exp
Pdl Jack must be set to either [EXP] or [EXP
+ AUX]. See System Setup to select.
Load Preset
MIDI Messages
MIDI program change message loads the Preset
from the Preset Slot of the given value 1-127.
Note: The bottom two Ladder LEDs will be lit when
Presets 6–127 are selected via MIDI or Device Manager
Receive/send using the USB Port or Exp Pdl Jack*.
CC 4: Expression Pedal
CC 9: TAP TEMPO
CC 14: ACTIVE/BYPASS (>=64 is Active)
CC 15: FREEZE (>=64 is Freeze)
Parameters: CC Messages Map
Morphing from Heel to Toe
Enter Save Mode by pressing and holding the FREEZE
Button, then a MIDI program change message will save
a Preset to the Preset Slot of the given value 1-127.
*Use a MIDI Converter Box
or a DIN to TRS or TRS cable
An Expression Pedal can be used to change any
grouping of knob Parameters in one smooth
gesture. Programming Expression Pedal is easy.
You simply need to set end points for Heel &
Toe. Here’s how:
1. Press Pedal fully Heel down.
2. Adjust any combination of the Parameter
control knobs.
3. Press Pedal fully Toe down.
4. Adjust any or combination of the Parameter
control knobs.
5. Save it or lose it. See “Saving a Preset.”
Clear Expression Pedal Mappings
To clear the Expression Pedal mappings for the
knobs, hold the ACTIVE Footswitch and, while
holding, press the ACTIVE Button until the Preset
Ladder LEDs flash twice.
Save Preset
Expression Pedal Knob Functions – Secondary Parameters
Delay
Predelay 0-2,000 msec
Rate
Rate of modulation
Mix
Dry/Wet Mix
Rear Panel
Power
9VDC center-negative
Mono/Stereo Switch
Left = Mono (TS plug)
Right = Stereo (TRS plug)
In Stereo, Tip is OUT1, Ring is OUT2
I/O Level Switch
Left - Guitar
Right - Line/Effects Loop
IN
Sta arnd d T no) S (mo
or TR stereo S ( )
Q
Resonance of Lo & Hi filters
Q has no effect if Lo/Hi
knobs are set to mid point
Depth
Depth/intensity
of modulation
EXP
Connect Expression Pedal,
Auxiliary Switches or TRS MIDI
(See System Setup)
Mini USB
Software updates
& MIDI over USB
Out Lvl
Boost/Cut output level
Center for unity gain
Press button to toggle
Secondary/Primary parameters
OUT1 & OUT2
In Mono, both outputs
have the same dry signal

Product specificaties

Merk: Eventide
Categorie: Niet gecategoriseerd
Model: Blackhole

Heb je hulp nodig?

Als je hulp nodig hebt met Eventide Blackhole stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Eventide

Eventide

Eventide Riptide Handleiding

25 Maart 2024
Eventide

Eventide Omnipressor Handleiding

7 December 2023
Eventide

Eventide Space Handleiding

15 November 2023
Eventide

Eventide TimeFactor Handleiding

15 November 2023
Eventide

Eventide TriceraChorus Handleiding

27 Juli 2023
Eventide

Eventide ModFactor Handleiding

26 Juli 2023
Eventide

Eventide Barn3 OX9 Handleiding

5 Juli 2023
Eventide

Eventide Misha Handleiding

5 Mei 2023
Eventide

Eventide PitchFactor Handleiding

8 April 2023
Eventide

Eventide Generate Handleiding

8 Maart 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Senal

Senal ME-220-CL Handleiding

21 November 2024
Senal

Senal ASM-4 Handleiding

21 November 2024
Senal

Senal CS-88 Handleiding

21 November 2024
Senal

Senal CSP-162 Handleiding

21 November 2024
Senal

Senal ASM-3 Handleiding

21 November 2024
Senal

Senal ASM-5 Handleiding

21 November 2024
Senal

Senal PS-48B Handleiding

21 November 2024
D-Link

D-Link DWA-142 Handleiding

21 November 2024
Senal

Senal CSP-142 Handleiding

21 November 2024
Senal

Senal SCI-3212 Handleiding

21 November 2024