Ernitec NVR 32 Handleiding

Ernitec Videorecorder NVR 32

Lees hieronder de 📖 handleiding in het Nederlandse voor Ernitec NVR 32 (4 pagina's) in de categorie Videorecorder. Deze handleiding was nuttig voor 15 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4

Fully understand this document before using this device, and

strictly observe rules in this document when using this device. If

you install this device in public places, provide the tip "You have

entered the area of electronic surveillance" in an eye-catching

place. Failure to correctly use electrical products may cause fire

and severe injuries.

It alerts you to moderate dangers which, if not

avoided, may cause minor or moderate injuries.

It alerts you about risks. Neglect of these risks may

cause device damage, data loss, device

performance deterioration, or unpredictable results.

It provides additional information.

ŸStrictly observe installation requirements when installing the

device. The manufacturer shall not be liable for device damage

caused by users' non-conformance to these requirements.

ŸStrictly conform to local electrical safety standards and use

power adapters that are marked with the LPS standard when

installing and using this device. Otherwise, this device may be

damaged.

ŸUse accessories delivered with this device. The voltage must

meet input voltage requirements for this device.

ŸIf this device is installed in places with unsteady voltage, ground

this device to discharge high energy such as electrical surges in

order to prevent the power supply from burning out.

ŸWhen this device is in use, ensure that no water or any liquid

flows into the device. If water or liquid unexpectedly flows into

the device, immediately power off the device and disconnect all

cables (such as power cables and network cables) from this

Precautions Special Announcement

For more information please refer to our website.,

ŸAvoid heavy loads, intensive shakes, and soaking to prevent

damages during transportation and storage. The warranty does

not cover any device damage that is caused during secondary

packaging and transportation after the original packaging is

taken apart.

ŸProtect this device from fall-down and intensive strikes, keep the

device away from magnetic field interference, and do not install

the device in places with shaking surfaces or under shocks.

ŸClean the device with a soft dry cloth. For stubborn dirt, dip the

cloth into slight neutral cleanser, gently wipe the dirt with the

cloth, and then dry the device.

ŸDo not jam the ventilation opening. Follow the installation

instructions provided in this document when installing the device.

ŸKeep the device away from heat sources such as radiators,

electric heaters, or other heat equipment.

ŸKeep the device away from moist, dusty, extremely hot or cold

places.

ŸIf the device is installed outdoors, take insect- and moisture-

proof measures to avoid circuit board corrosion that can affect

monitoring.

ŸRemove the power plug if the device is idle for a long time.

ŸWhen unpacking, please first confirm whether fragile label is

damaged, if damaged, please contact customer service or sales

personnel in time. The company will not be liable for any human-

made damage to fragile labels.

ŸAll complete products sold by the manufacturer are delivered

along with nameplates, quick setup guide and accessories after

strict inspection. The manufacturer shall not be liable for

counterfeit products.

ŸThe manufacturer will update this manual according to product

function enhancement or changes and regularly update the

software and hardware described in this manual. The updated

content will be added to new versions of this manual without prior

notice.

ŸThis manual may contain misprints, technology information that

is not accurate enough, or product function and operation

description that is slightly inconsistent with the actual product,

the final interpretation of company is as a standard.

ŸThis manual is only for reference and does not ensure that the

information is totally consistent with the actual product. For

consistency, see the actual product.

NOTE

device.

ŸIf this device is installed in places where thunder and lightning

frequently occur, ground the device nearby to discharge high

energy such as thunder strikes in order to prevent device

damage.

CAUTION

Open the package, check the appearance of product for no

obvious damage, and confirm the item list for table 1-1 is

consistent.

Table 1-1 Packing list

Open Package Examination

NOTE

CAUTION

WARNING

Component

Network video recording

Countersunk head black screws

Power Cord

Green female wiring terminal

Mouse

Quick Setup Guide

Countersunk head imperial white

screws

Quantity

2(8)

Remark

Table -2 1 Front panel description

2.1 Device Ports

Different devices may have different ports and multi-head

cables; Please refer to the actual product.

NOTE

D evice Structure2

Table -2 2 Rear panel description

For front panel description of device refer to table 2-1.

Port Name Description

HDD

Indicator

Hard disk status indicator.

This indicator flashes when data is transmitted.

USB 2.0 Support connected to an USB mouse or USB disk.

PWR

Indicator

When the NVR is operating, the PWR indicator

is steady on. When the NVR is shut down, the

PWR indicator is off.

PoE

Indicator

PoE network status indicator.

This indicator flashes when data is transmitted.

For rear panel description of device, please refer to table 2-2.

Port Name Description

HDMI1/2

Support connected to 3.0 U disk.

VGA

USB .3 0

Alarm input and alarm output, 1A&1B~4A/4B are

alarm out. A is RS 485+, B isRS485-.

Audio out/

Audio in

Audio output and audio input.

LAN

RJ 1000 Mbps adaptive Ethernet interface, connect

to intranet to add cameras.

The hard disk of the NVR must be provided by the user. Take the

following steps to install the hard disks：

Step 1 Remove the screws for fixing the cover and take down the

cover.

Step 2 Put the hard disk under the hard disk bracket, hold the hard

disk with one hand and aim the hard disk hole at the

bracket hole, then fix the screws for hard disk(Install the

hard disk near the fan first).

Figure -3 1 Installing the hard disk

2 2. Device Dimensions

Different devices may have different dimensions; Please

refer to the actual product.

NOTE

3Device Installation

Figure 2-1 Dimensions (Unit:mm)

Step 3 Repeat step 2 to install other hard disks, and insert the hard

disk data cables and power cables, then replace the upper

cover and fasten the fixing screws.

Hard disk

Hard disk bracket

AC 110V/220V power input interface.

RS232

Standard Rs232 serial communication interface

of the device.

Power switch.

Safe ground screw of the device.

376

440

376

369

ALARM I/O

RS 485

WAN

RJ 1000 Mbps adaptive Ethernet interface, connect

to Internet .

e SATA External hard disk interface.

Video output interface. If the Auxiliary Screen is

enable, HDMI1’s output is main screen, VGA’s

output is auxiliary screen.

Hanger 2

NVR 32

channel

Quick Setup Guide

Item no.: 0070-10404

Re cord

Al ar m

Network System

Sy ste m

Channel

802.1X

DDNS

Emai l

Port Mappi ng

P2P

IP Fi lter

SNMP

PPPOE

3G/ 4G

Net work Traff ic

Platform Ac ce ss

DHCP

Port IPv4CCT V

IP Ad dress

Subnet Mas k

Defa ul t Gatew ay

Obtai n DNS Automati ca ll y

Preferred DNS S erver

Alte rnate DN S Serv er

192 . 1 68 . 0 . 12 1

255 . 2 55 . 25 5 . 0

192 . 1 68 . 0 . 1

8 . 8 . 8 . 8

Apply

Re co rd

Al ar m

Network Syst em

Ge ne ral

Mo ti on De tection

Video Los s

Intelligent Analys is

Alarm In

General

Ena ble Alar m

Apply

Ab no rm al Ala rm

Sy ste m

Channel

Advac ned Intel li gent Analy.

Al arm O ut

Loc al Intel li gent Analy s is

Ala rm Duration Time (s ec)

Buz zer Dur ation Tim e (sec)

Channel

Record Network

Alarm

System

Camera

Encode

OSD

Priv acy Zone

Record Schedule

Disk

Storage Mode

S.M.A.R.T

Disk Detec tion

RA ID

Network

DDNS

IP Filter

3G/4G

802.1X

Port Mapping

P2 P

SNMP

. . .

General

Video L oss

In te lligen t Analysis

Alarm In

Information

General

User Acc ount

Sec urity C enter

Auxiliary Screen

Ma in te na nc e

Au to Re boot

Logs

Abnormal Alarm

Motion D etection

Layout

Sensor Settin g

Mic rophone

Smart

ROI

Human Thermome t

In telligent Track ing

Disk Calculation

FTP

Advanced Inte llige nt Analysis

. . .

In some environments, if the power supply is abnormal,

the NVR may not work properly. In severe cases, the NVR

may be damaged. In these environments, it is

recommended to use regulated power supply.

Device Operation

4.1 Startup

Before starting NVR, ensure that the NVR is connected to a

power supply properly and a monitor is connected to the HDMI or

VGA interface of the NVR correctly. After starting the NVR, there

is a login window located in the center, as shown in figure 4-1.

CAUTION

Figure 4-3 Topology of the NVR

Plug in power to access the NVR user page. The wizard

window would show at first time, users can configure quickly or

close immediately. For configuration details please refer to main

menu.

Right-click on the main interface at any where to access the

main menu. Main menu comprises Channel, Record, Alarm,

Network and System settings, as shown in figure 5 1.-

Quick Configuration5

.4 2 Topology of the NVR

cameras an For the NVR evice are on I ternet, or at same d d n

network, NVR and IP cameras can comm uni cate with each other

smoothly with WAN port. Figure 4-3 shows the network topology

of the NVR.

4.3 Special Function

Some functions are applicable for some special cameras,

such as Microphone, Human thermometer, Smart, Intelligent

Analysis, Advanced Intelligent Analysis, please refer to actual

camera channels.

4.4 Power off

Enter the Main Menu System Maintenance Shutdown > > > to

power off the NVR. Or turn off the power switch.

4.4 Quick menu

Put the mouse arrow on bottom of live video interface, the quick

menu will be showing. You can set layout to view live video, switch the

split screen, auto sequence, playback and so on.

NOTE

Ÿ The default name is admin, and NVR needs to activate, please create

new password of device and channels to activate.

Ÿ Users can set pattern to unlock quickly.

Ÿ .

Figure 4-2 Login interface

Pas

Figure 4-1 Activation interface

Figure 5-1 Main menu

Figure 7-1 Login

Mobile Client 6

ŸNetwork, 802.1X DDNS SNMP, , and interface to set network

parameters.

ŸEmail: Set E-mails for sending and receiving alarm messages

and password retrieval message.

ŸPort Mapping: Set the ports for remote scanning.

ŸP2P: Add NVR into device list of App by accessing the QR code.

ŸIP Filter: Settings for creating black list or white list.

Ÿ3G/4G: Use 3G/4G modem plug to NVR provide the network.

ŸPPPoE: Point to point network to access NVR directly.

ŸNetwork Traffic : View the send and receive rate of network.

ŸPlatform Access: Set URL parameters for accessing to

CMS(Center Management System).

5.6 Live Video

nter the user name and password in the login interface, and

click Login to enter the real-time video interface. As shown in

Figures 5-5.

Figure 5-5 Live video

The NVR also can be accessed in a Web browser. Open a web

browser like Chrome 45 and enter the IP address of device (The

default IP address is 192.168.0.121) in the address box, and

press . The login page is displayed as shown in figure 7-1.Enter

Web ccessing A

Search for “InView Pro4” in App Store or Google Play to

download and install the App. Use the App to scan the QR code,

which you can find it on the backboard of the NVR and on P2P

settings page (Main menu>Network>P2P) in user interface. Then

input the NVR's user name and password to add the NVR to the

device list. Users can manage the device on the APP.

5.5 System

System settings contain Information, General, User Account,

Security Center , Layout, Auxiliary Screen, Logs, Maintenance

and Auto Reboot, as shown in figure 5-4.

5.4 Network

Network settings contain Network, 802.1X, DDNS, E-mail,

Port Mapping, P2P, IP Filter, SNMP, 3G/4G, PPPoE, Network

Traffic and Platform Access, as shown in figure 5-3.

Figure 5-3 Network

5.2 Record

Record settings contain Record Schedule, Disk, Storage, RAID,

S.M.A.R.T, Disk Detection, Disk Calculation and FTP.

ŸRecord Schedule: Set record schedule and storage strategic.

ANR is auto network recording, if the camera is plugged SD card

and enabled record, if camera is disconnected, when the

connection is recovered, NVR will copy the recording of the lost

videos.

ŸEnter S.M.A.R.T interface to view the state of disks. Disk

detection can detect the disks.

ŸRAID: If users install more than four disks and want to keep the

data safety, it is recommended to build RAID.

ŸDisk Detection: Check the disk health status.

ŸDisk Calculation: Two methods to calculate.

ŸFTP: File Transfer Protocol, set the FTP path to save the alarm

information if linkage to FTP.

5.1 Channel

Channel settings contain Camera, Encode, Image, OSD,

Privacy Zone, ROI (region of interest), Microphone, Human

thermometer, Smart, and Intelligent tracking.

ŸCamera: Users can add cameras automatically by clicking Click

to Add, and add manually by clicking Add. Tick cameras then

click Delete to delete cameras. Users can batch update software.

ŸEncode: Users can set stream, encode type, resolution, frame

rate, bit rate type, bit rate and so on.

ŸSensor setting: Adjust image parameters and users can set

senor parameter.

ŸOSD: Customize time and channel name displaying in the live

video page.

ŸPrivacy Zone: Set a privacy zone by clicking ana dragging

cursor and double-click an exist private area to delete it. Support

up to 4 zones.

ŸSome of these sett

ings can be copied to other channels by

clicking button.Copy

ŸMicrophone, Human Thermometer Smart Intelligent , , and

Tracking are the special functions for some models, not

applicable for all cameras.

5.3 Alarm

Alarm settings contain General, Motion Detection, Video Loss,

Advanced Intelligent Analysis, Intelligent Analysis, Alarm in,

Abnormal Alarm, Alarm out and Local intelligent analysis, as

shown in figure 5-2. Figure 5-2 Alarm Figure 5-4 System

ŸInformation: View the basic information, such as System,

Network, Channels, Disk, Alarm.

ŸGeneral: Include system, date and time, time zone, DST.

ŸUser Account: Add users and set advance setting (auto login,

password double authentication, boot wizard).

ŸSecurity Center : Modify the password, pattern unlock, secure

Email, Secure question.

ŸLayout: Add layouts to preview live video of the channels.

ŸAuxiliary Screen: Use HDMI and VGA to view live video at the

same time. HDMI port output acts as main screen.

ŸLogs: Users can export logs ( operating and alarm logs) if plug

in a USB disk.

ŸMaintenance: Include shutdown, reboot, exit system, reset,

import configuration, export configuration and update.

ŸAuto Reboot: Enable this function and the device will restart

periodically.

ŸGeneral: Enable or disable alarm and set duration time of

alarm and buzzer.

ŸMotion Detection: Enable this function, if detects any

movement, it will alarm.

1. Event actions: Contain buzzer, alarm out, push message to

App, pop-up message to monitor, send E-mail and post

recording (after enabling, choose the recording time from drop

list.)

2. Area: Set motion detection area. Press left button and drag the

cursor to add a detection area, and double-click an area to

delete it.

3. Schedule: Set schedule to enable or disable motion detection

alarm. There are three methods to set: the first is clicking the

double arrows button to choose all day. The second, click and drag

the cursor to select periods. The third, click one by one.

ŸVideo Loss, Intelligent Analysis are same settings as motion

detection. Advanced Intelligent Analysis is used for thermal

cameras, alarms for smoker detection, smoke and flame

detection and fire spot detection.

ŸAlarm In / Alarm out: Settings for I/O alarming. Abnormal

Alarm can tick disk error, IP conflict, network disconnected.

ŸLocal Intelligent Analysis: It is up to be set for 4 channels, set

local intrusion parameter on NVR.

NOTE

Add IP cameras

WAN

Forgot pas s word

admin

English

Pa ttern Unlo ck

Activ ation

--Valid password range [6-32] characters.

--At least 2 kinds of numbers, lowercase, uppercase or specia l.

-- Only these special characters ar e suppor ted !@#$*+-=_%&”’.

Language

Username

Enter a new password

Confirm the new password

Enter channel default password

English

admin

Pas sword

Re cord

Al ar m

Network System

Sy ste m

Channel

General

Informati on

Us er Account

Secur ity Center

Auxili ary S creen

Layout

Logs

Auto Reboot

Maint enance

De vice ID

Dev ice Name

Dev ice Type

Model

Fir mw are Vers ion

HDD Nu mber

Channels Supported

Alarm In

Alarm Ou t

Audio In

Audio Out

U- boot Vers ion

Ker nel V ers ion

16081 20B122F

16081 20E3619

v4.6.1610.0000.00 03.0.x.x

NV R3932E4

NV R

evice

Network

Channel

Di sk

Al ar m

B011003AGHGQT 64X XXX

Sy stem

ŸFormat the disk and all data on disk will be lost, please be

careful to do this.

ŸBefore replacing the hard disk, the power must be turned off.

ŸThe disks of building RAID should be enterprise level, and the

capacities are better at the same.

ŸFor the safety of disks, please make sure the stabilization of

power on.

NOTE

The user name and password are same as in the UI interface.

Product specificaties

Merk:	Ernitec
Categorie:	Videorecorder
Model:	NVR 32
Kleur van het product:	Zwart
Gewicht:	4650 g
Breedte:	372 mm
Diepte:	315 mm
Hoogte:	47 mm
Gewicht verpakking:	6000 g
LED-indicatoren:	Ja
Aan/uitschakelaar:	Ja
Maximum resolutie:	- Pixels
Aantal USB 2.0-poorten:	2
Aantal HDMI-poorten:	1
Aantal Ethernet LAN (RJ-45)-poorten:	2
Gezichtsdetectie:	Ja
RS-232 port:	1
Audio-uitgang:	3,5 mm
Ethernet LAN, data-overdrachtsnelheden:	10,100,1000 Mbit/s
Netwerkstandaard:	IEEE 802.1x
Aantal poorten USB 3.2 Gen 1 (3.1 Gen 1) Type A:	1
Rack-montage:	Ja
Ethernet WAN:	Ja
Lijningang:	Ja
HDD capaciteit:	- GB
HDD interface:	SATA
Power over Ethernet (PoE):	Ja
Maximum aantal HDD's per behuizing:	4
Maximale opslagcapaciteit:	16 TB
VGA (D-Sub) uitgang ports:	1
Rackcapaciteit:	1.5U
Aantal eSATA-poorten:	1
Videoingangkanalen:	32 kanalen
Wifi:	Nee
AC-ingangsspanning:	110/220 V
eSATA:	Ja
HDMI-uitgang:	Ja
Ondersteunende oplossingen:	8MP
Garantieperiode:	5 jaar