Erica Synths MIDI<->CLK Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Erica Synths MIDI<->CLK (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
MIDI<->CLK
CLK IN/OUT DIV
MULT 1 MULT 2
PPQ
MULTDIV
MIDI OUT
MIDI IN
2
4
8
24
4
1
4
8
16
2
4
8
Thank you for purchasing
Erica Synths MIDI <-> Clock module!
This is essential module, if you wish
to sync your modular system to
MIDI devices. What sets Erica Synths
MIDI <-> Clock module apart form
others is that it works BOTH WAYS –
it derives analogue clock from MIDI
messages AND, flip a switch, and you
can turn incoming analogue clock
to MIDI clock and sync your MIDI
devices to your modular. For more
versatility the module can be used
with several incoming clock PPQs,
plus, divisions and multiplications
of incoming clock are available
straight away.
FEATURES:
Bidirectional MIDI to clock conversion
1, 4 and 24 PPQ selection
Division by 2, 4, 8
Multiplication by 4, 6, 16
Two simultaneous multiplied clock
outputs
Start/Stop button
MIDI start/stop message
implementation
Incoming/outgoing clock LEDs
TECHNICAL SPECIFICATIONS:
Clock signal level 0 - +5V ......................
CLK signal duty circle ................... 50%
Power consumption ..............................
.......................25mA@+12V, 0mA@-12V
Module width ................................ 6HP
Module depth ............................ 20mm
This in input of the clock in MIDI
OUT mode and output of the
clock in MIDI IN mode.
NB! Do not plug clock signal
here in MIDI IN mode! Its clock
output now!
LEDs indicate clock rate for each
of clock outputs
These are outputs of multiplied
clock. Multiplication rate is 2, 4,
8 for MULT1 output and 4, 8, 16
for MULT2 output
Select division rate for DIV output!
Note that division is done on
BPM basis
This is output of the divided
clock
This is MIDI activity LED
Connect your MIDI controller
here!
Select multiplication rate for
both MULT1 and MULT2 outputs!
Note that multiplication is done
on BPM basis
This button activates outgoing
clock, in case MIDI device doesn’t
send MIDI start/stop messages.
If the module is in MIDI IN mode:
*The module will start to output
clock signal automatically with
MIDI STRAT message
*Push the button promptly to stop
the clock output to all outputs
on the module, even if the MIDI
controller is running
*Push the button promptly to
resume clock output instantly
*Push the button for 1,5to resume
clock output in the moment, when
MIDI sequence is on the first step
of the sequence
If the module is in MIDI OUT
mode:
*With a clock signal plugged
in CLK IN/OUT, push the button
promptly, and the module will
send MIDI START message and
start to output MIDI clock
*When clock is running, push the
button promptly and the module
will send MIDI STOP message and
a MIDI device (eg. sequencer) will
stop on the current step
*To resume the sequence, push
the button promptly, and the
module will send MIDI CONTINUE
message
*To reset the sequence and start
it from beginning, push and hold
the button for 1,5, and the module
will send MIDI START message.
In MIDI OUT mode we can’t
output correct 24PPQ MIDI
clock starting form the first click,
because we do not know the
period of the incoming clock, yet.
Therefore we need manual start.
Select clock conversion mode!
If you input MIDI CLOCK, set the switch to MIDI IN position, and you will get analogue
clock on CLK IN/OUT jack and divided or multiplied clock on all other jacks. Clock will
appear on the output only, if MIDI Start message will be present.
If you input ANALOGUE CLOCK to CLK IN/OUT jack and want to output MIDI clock, set
the switch to MIDI OUT position! DIV and MULT outputs will as incoming clock dividers or
multipliers.
Depending on direction, this
switch select desired PPQ
of the clock.
If you convert MIDI clock to
analogue clock, you can select
PPQ of outgoing clock. To clock
most of sequencers, select 4PPQ!
If you convert analogue clock
to MIDI clock, you need to
set incoming clock division in
order to get correct 24PPQ
MIDI clock. If you input clock
that corresponds to BPM clicks,
select 1, if you input clock from the
sequencer, select 4.
MIDI<->CLK
SAFETY INSTRUCTIONS
DISPOSAL
Please follow the instructions for use of this
Erica Synths module below, ‘cause only this
will guarantee proper operation of the module
and ensure warranty from Erica Synths.
Water is lethal for most of the electric devices,
unless they are made waterproof. Erica
Synths module is NOT intended for use in
a humid or wet environment. No liquids or
other conducting substances must get into
the module. Should this happen, the module
should be disconnected from mains power
immediately, dried, examined and cleaned by
a qualified technician.
Do not expose the module to temperatures
above +50° C or below -20° C.
Transport the instrument with modules
installed carefully, never let it drop or fall over.
Warranty does not apply to modules with
visual damages.
The module has to be shipped in the original
packaging only. Any module shipped to us
for return, exchange and/or warranty repair
has to be in its original packaging. All other
deliveries will be rejected and returned to you.
Make sure you keep the original packaging
and technical documentation.
You will find Erica Synths terms of warranty at
http://ericasynths.lv/en/terms/
Items for return, exchange and/or warranty
repair have to be sent to: Erica Synths,
Andrejostas Str.12, Riga, Latvia, LV-1045
This device complies to the EU guidelines and is
manufactured RoHS conforming without use of
led, mercury, cadmium and chrome.
Nevertheless, this device is special waste and
disposal in household waste is not
recommended.
Designed and made in Latvia.
User manual by Girts Ozolins@Erica Synths.
Design by Baiba Stelle.
Copying, distribution or any commercial use in
any way is prohibited and needs the written
permission by Erica Synths.
Specifications are subject to change without
notice.
In case of any questions feel free to contact us
via e-mail info@ericasynths.lv
Check out other Erica Synths modules & devices
at www.ericasynths.lv
MIDI<->CLK


Product specificaties

Merk: Erica Synths
Categorie: Niet gecategoriseerd
Model: MIDI<->CLK

Heb je hulp nodig?

Als je hulp nodig hebt met Erica Synths MIDI<->CLK stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Erica Synths

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd