Epson AcuLaser CX11N Handleiding

Epson Printer AcuLaser CX11N

Lees hieronder de 📖 handleiding in het Nederlandse voor Epson AcuLaser CX11N (8 pagina's) in de categorie Printer. Deze handleiding was nuttig voor 33 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/8
Start Here
Cover A
Epson AcuLaser® CX11N/CX11NF
Unpack
Note: The illustrations show the CX11NF, but the instructions apply to both the
CX11N and CX11NF unless otherwise noted.
1 Check that you have the following:
4 toner cartridges (Cyan, Magenta, Yellow, Black)•
• Photoconductor unit
• USB cable
• Power cord
• Documentation: Basics Guide Fax Guide, (CX11NF only)
• 3 software CD-ROMs
2 Select a location for the CX11N. Make sure you allow enough space
around the product to ensure smooth operation.
a 36.2 in. (920 mm)
b 10.2 in. (258 mm)
c 34.2 in. (868 mm)
d 3.9 in. (100 mm)
e 11.8 in. (300 mm)
The optional 500-Sheet Paper Cassette Unit adds
5.1 in. (130 mm) to the bottom of the CX11N.
3 Remove all the packing tape from the outside of
the unit.
4 Raise the scanner unit, then open cover C
and pull out the insert.
5 Close cover C and lower the scanner unit.
6 Open cover A and remove the foam
insert. Then close the cover.
7 Open the document cover and remove
the insert. Then unlock the carriage lock.
8 Close the document cover.
Cover C
1
9 Connect the power cord to the
CX11N and to an AC outlet.
10 Push the power switch to .On
Install Toner Cartridges
Caution: Make sure the CX11N is turned on before installing the toner
cartridges. Do not install the photoconductor before installing the toner
cartridges.
1 Open cover A and remove the
tape and plastic insert.
2 In the LCD screen the message
Install [X] Toner Cartridge
appears, where is one of [X]
the following:
• Y: Yellow
• M: Magenta
• C: Cyan
• K: Black
3 Remove the toner cartridge from its
package and gently shake it.
Warning: Do not touch the toner. Keep
the toner away from your eyes. If toner
gets on your skin or clothes, wash it off
with soap and water immediately.
4 Hold the tag and gently pull the toner seal
until it comes completely out.
5 Slide the toner cartridge into the tracks inside the printer. Push evenly on
both sides until the cartridge stops securely in its slot.
If the cartridge doesn’t
seem to be installed fully,
remove it and reinstall it.
Caution: Don’t force the
cartridge into the printer
or force the lock lever
down, or you may damage
the printer.
6 Push down the lever to
lock the toner cartridge.
Note: The toner cartridge
is installed securely when
you cannot turn the lock
lever any further.
7 Close cover A and confirm the message in the LCD screen.
The LCD screen will display the next cartridge that needs to be
installed. Open cover A and repeat steps 3 to 7 for each of the
remaining toner cartridges.
Install Photoco
C
c
1
2
3
4
5
6
1
2
3
4
5
6
3
2
4
5
1
2
3
4
5
6
7
8
a
1
2
3
4
5
Install Photoconductor
Caution: Make sure the CX11N is turned on and you have installed all the toner
cartridges, as described in the previous section.
1 Install Photoconductor appears in the LCD screen. Lift up the scanner.
2 Lift up cover B and raise the orange lever
inside, on the right.
3 Remove the photoconductor from its package
and pull off the protective sheet.
Caution: Do not touch the belt on the top
of the photoconductor or the blue roller beneath
it; otherwise, print quality may decrease.
Avoid exposing the photoconductor to light any longer than necessary.
Do not touch any other components inside the CX11N.
4 Hold the photoconductor by
its handle and insert it into the
slots marked with blue arrows
inside the CX11N. Push it in
until it clicks into place.
5 Flip down the orange lever,
then close cover B.
6 Pull out the extension tray if necessary. Lower the scanner unit to its
original position.
Set Fax/Printer Information
CX11NF
1 Select the Country: Press the or button to select the country,
then press the button.
2 Select the Language: Press the or button to select the language,
then press the button.
3 Set the Date and Time: Press the or button to select the year,
month, day, hour, and minute. Press the button after selecting each
item. The CX11NF then resets itself and reboots.
4 Turn off the CX11NF.
5 Connect an RJ-11 cord to
the telephone line interface
on the CX11NF and to the
RJ-11 jack on the wall.
Note: An RJ-11 cord is not
included with the CX11NF.
6 Turn on the CX11NF.
CX11N
1 Press the Setup button.
The Setup light turns on and the LCD screen shows for a Setup Mode
few seconds, then changes to the Setup menu screen.
2 Press the button until is selected, then press the Printer Settings
button.
3 Press the button until is selected, then press the Setup Menu
button.
4
3


Product specificaties

Merk: Epson
Categorie: Printer
Model: AcuLaser CX11N

Heb je hulp nodig?

Als je hulp nodig hebt met Epson AcuLaser CX11N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Printer Epson

Handleiding Printer

Nieuwste handleidingen voor Printer