Epcom TT-676 Handleiding

Epcom AV extender TT-676

Lees hieronder de 📖 handleiding in het Nederlandse voor Epcom TT-676 (3 pagina's) in de categorie AV extender. Deze handleiding was nuttig voor 35 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

· Important Safety Notice

· Introduction

· Features

· Installation Requirements

· Interfaces

· Installation Procedures

1. Do not mix up HDMI to R J45 transmitter and R J45 to HDMI receiver

before installation.

2. Do not hot plug when it is working.

3. Use DC5V/2A power supply only. Make sure specification matched

if using 3rd party adapters.

4. Static electricity will cause damage of the device, please do ESD

protection when using the device.

1. Zero latency lossless compression.,

2. 4K@60Hz HDMI signal can be transmitted 40-70 meters through a

CAT5E/6/6A/7 network cable.

3. Supports up to 10 receivers in cascade, auto adapt to display resolution .

4. The receiver supports S/PDIF output.

5. Supports Dolby audio(Dolby Digital Plus/Dolby TrueHD/Dolby Digital/Dolby atmos)

6. Supports HDR(YUV4:4:4), maximum transmission rate 18Gbps.

7. Transmitter support one HDMI loop-out

8. Support bi-directional IR passback function (20～60KHz), cascade when

10 receiver available

9. One receiver can be powered by the transmitter via network cable, Only

on the first receiver.

10. Anti - lightning, anti - surge, anti - static protection.

11 Metal casing, stable and durable. .

Transmitter unit x1pc Receiver unit x1pc

HDMI OUTPUT

1. HDMI source device (compute graphics card, DVD, PS3, )HD

monitoring equipment etc.

2. HDMI display device like SDT V, HDTV, projector with HDMI por t.

3. UTP/STP CAT5E/CAT6/CAT6A/CAT7 cable. Follow standard IEEE-568B,

It is recommended to select a network cable with less loss and crosstalk.

2. Receiver (RX)

1. Connection

IR blaster extension

cable x1pcs

IR receiver extension

cable x1pcs

DC5V/2A x1pc

DC5V input

When there is power and no HDMI signal, the

indicator will flash, when there is HDMI signal,

the indicator will light solid blue

This HDMI Extender includes a transmitter unit and a receiver unit,

allows HDMI signal to be transmitted up to 40 meters at 4K resolution

using a CAT5E network cable, and up to 70 meters at 4K resolution

using a CAT6/6A/7 network cable. It supports bi-directional IR passback

with a wide IR frequency 20-60KHz. The receiver can be powered by the

transmitter (Connect the power supply to the transmitter only), please

note that this HDMI Extender can not use with switch or router. It is perfect

for outdoor advertising, video clips, monitor system, home entertainment,

and conference, etc.

· Package Contents

1. Transmitter (TX)

User manual x1pc

Connect with HDMI display device

Connect with DC5V/2A power adapter

HDMI INPUT

IR IN

Connect with IR receiver extension cable, please

make sure the remote control used is within the

effective range

Connect with IR blaster extension cable, please

get closer to the source device while using

IR OUT

③

④

⑤

⑦

⑥

⑧

DC5V input

Connect with network cable

When there is power and no HDMI signal, the

indicator will flash, when there is HDMI signal,

the indicator will light solid blue

Connect with DC5V/2A power adapter

IR IN

Connect with IR receiver extension cable, please

make sure the remote control used is within the

effective range

Connect with IR blaster extension cable, please

get closer to the source device while using

IR OUT

①

②

③

④

⑤

⑦

⑥

⑧

Press to restart the device

HDMI OUTPUT Connect with HDMI display device

⑩

S/PDIF OUT Output digital audio signal.

Connect with network cable

①

②RJ45 signal output

Reset button Press to restart the device

HDMI IN

Note: Only the TX needs to be powered when one to one connection.

one to one:

IR OUT

IR IN IR OUT

IR IN

HDMI OUT

HDMI Display

Network cable

HDMI Display

IR OUT

IR IN

IR OUT

IR IN

HDMI DisplayHDMI Display

one to many：

IR OUT

IR IN IR OUT

IR IN

...10pcs

Network cable

HDMI IN HDMI OUT

HDMI OUTHDMI OUT

HDMI Display

Power/Signal

indicator

RJ45 signal input

Reset button

Power/Signal

indicator

RJ45 signal output Connect with network cable

① ② ③ ④ ⑤ ⑥ ⑦ ⑧

① ② ③ ④ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩

⑨

Audio switch Choose to decode audio from HDMI or ARC

output from fiber optic interface

· Specification

106.0(L) x 99.0(W) x 2 6.2(H)mm

TX 210g RX:210g :

DC5V/2A

TX＜4W RX＜4W

HDMI Extender

1 ) IR blaster extension cable should plug in the IR OUT port of the

transmitter and receiver, IR receiver extension cable should plug in

the IR IN port of the transmitter and receiver.

2 ) The emitter of the IR blaster extension cable should be as close as

possible to the IR receiving window of the source device.

3 ) Face the receiving head of the IR receiver extension cable to the user

for convenient remote control.

· FAQ

Q: There is no output on screen when all connections are correct?

A: 1) Please make sure the HDMI cables supports 4K×2K if the output

signal from the source device is 4K×2K resolution.

2) Please check and make sure the network cable insert to the RJ45

port well.

3) Restart the transmitter or receiver by pressing the reset button.

Q: Black screen happened on the display/monitor?

A: 1) Check if the length of the cable is within the specified range.

2) Reset the transmitter to re-built the connection.

Q: The display shows unusual color or no sound?

A: 1) Reset the transmitter or receiver to re-built the connection.

2) Check if the HDMI cables are connected well.

3) Reconnect the network cable.

It is recommended to use a length range within 2~70m network [NOTE]:

cable. If the cable is too short, there may be no display output

because the signal is too strong. If the cable is too long, the

output may be with poor quality.

The product name and brand name may be registered trademark of

related manufactures. and may be omitted on the user manual.™ ®

The pictures in this user manual are just for reference. The terms HDMI,

HDMI High-Definition Multimedia Interface, and the HDMI Logo are

trademarks or registered trademarks of HDMI Licensing Administrator, Inc.

We reser ve the rights to make changes without further notice to a product

or system described herein to improve reliability, function or design.

Disclaimer

Follow the standard of IEEE-568B, It is recommended to

select a network cable with less loss and crosstalk.

1-Orange/white 2-Orange 3-Green/white

4-Blue 5-Blue/white 6-Green

7-Brown/white 8-Brown

Note: Up to 1 0 receivers can be cascaded, and the HDMI signal

output of it can be adaptive to the display resolution.

1 ) Connect the source device to the HDMI IN port of the transmitter with

an HDMI cable, and connect the HDMI OUT port of the receiver to the

display device with another HDMI cable.

2 ) Connect the CAT OUT port of the transmitter and the CAT IN port of

the receiver via a network cable (CAT5E/CAT6/CAT6A/CAT7). If

cascading is used, connect the CAT OUT port of the previous receiver

to the CAT IN port of the next receiver.

3 ) If using HDMI loop out, connect the display device to the HDMI OUT

port of the transmitter.

4 ) Plug the power supply into the device to get started.

2. Connection instruction

3. IR User Guide

Transmi ssion

Distance

CAT5E

CAT6/6A/7

≤40m

≤70m

LPCM/DTS-HD/DTS-Audio/Dolby Digital Plus

Dolby TrueHD/Dolby Digital/Dolby atmos

480i@60Hz 480p@60Hz 576i@ 50Hz、、、

576p@50Hz 720p@5 0/60Hz、、

1080i@50/60Hz 1080p@50/60Hz、、

3840x2160@24/25/30/60Hz

HDMI 2 0.

HDCP 2 2.

1a Contact discharge level 3

1b Air discharge level 3 Implementation

of the standard: IEC61000-4-2

0.7~1.2Vp-p(TMDS)

Product specificaties

Merk:	Epcom
Categorie:	AV extender
Model:	TT-676
Kleur van het product:	Zwart
Soort:	AV-zender & ontvanger
Stroom:	2 A
Ondersteund audioformaat:	DTS, LPCM
Connectiviteitstechnologie:	Bedraad
Maximum resolutie:	3840 x 2160 Pixels
HDCP:	Ja
Maximale refresh snelheid:	60 Hz
Aansluiting voor netstroomadapter:	Ja
HDMI versie:	2.0
Remote (IR) ingang:	2
Digitale audio, optische uitgang:	1
Temperatuur bij opslag:	-10 - 70 °C
Remote (IR) uitgang:	2
HDMI in:	1
RJ-45 uitgang ports:	2
HDCP versie:	2.2
Bandbreedte:	18 Gbit/s
Aantal HDMI-uitgangen:	2
Receiver afmetingen (B x D x H):	99 x 106 x 26.2 mm
RJ-45 invoer ports:	1
Bedrijfstemperatuur (T-T):	0 - 50 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Bedrijfsspanning (ontvanger):	5 V
Receiver gewicht:	210 g
Transmitter afmetingen (WxDxH):	99 x 106 x 26.2 mm
Transmitter gewicht:	210 g
Stroomverbruik (zender) (max):	4 W
Ondersteundende kabel types:	Cat6, Cat6a, Cat7
Stroomverbruik (ontvanger) (max):	4 W
Bedrijfsspanning (zender):	5 V
Transition Minimized Differential Signaling (TMDS) input:	1.2 V