Energy ESW-M8 Handleiding

Energy Subwoofer ESW-M8

Lees hieronder de 📖 handleiding in het Nederlandse voor Energy ESW-M8 (4 pagina's) in de categorie Subwoofer. Deze handleiding was nuttig voor 55 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/4
WA-2
Owner's Manual
IMPORTANT SAFETY INSTRUCTIONS!
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wider blade or the third prong are provided for your safety. If the provided plug does not fit
into your outlet, consult an electrician for replacement of the obsolete outlet.
10. PROTECT the power cord from being walked on or pinched, particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped.
15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled with liquids,
such as vases, are placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply cord plug
from the AC receptacle.
17. The mains plug of the power supply cord shall remain readily operable.
The exclamation point, within an equilateral triangle, is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.
The lightning flash with arrowhead symbol within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electrical shock to
persons.
WARNING: To reduce the risk of fire or electrical shock, do not expose this apparatus to rain or moisture.
WARNING: No naked flame sources – such as candles – should be placed on the product.
Place the equipment near a main power supply outlet and make sure that you can easily access
the power breaker switch.
WARNING: This product is intended to be operated ONLY from the AC Voltages listed on the back panel
or included power supply of the product. Operation from other voltages other than those indicated may
cause irreversible damage to the product and void the products warranty. The use of AC Plug Adapters
is cautioned because it can allow the product to be plugged into voltages in which the product was
not designed to operate. If the product is equipped with a detachable power cord, use only the type
provided with your product or by your local distributor and/or retailer. If you are unsure of the correct
operational voltage, please contact your local distributor and/or retailer.
FCC AND CANADA EMC COMPLIANCE INFORMATION:
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Approved under the verification provision of FCC Part 15 as a Class B Digital Device.
Caution: Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate this device.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
EU COMPLIANCE INFORMATION:
Eligible to bear the CE mark, Conforms to European Union Low Voltage Directive 2006/95/EC;
Conforms to European Union EMC Directive 2004/108/EC.
WEEE NOTICE
Note: This mark applies only to countries within the European Union (EU) and Norway.
This appliance is labeled in accordance with European Directive 2002/96/EC concerning
waste electrical and electronic equipment (WEEE). This label indicates that this product
should not be disposed of with household waste. It should be deposited at an appropriate
facility to enable recovery and recycling.
WIRELESS TRANSMITTER COMPLIANCE INFORMATION:
The term “IC:” before the radio certification number only signifies that Industry Canada technical
specifications were met. This equipment complies with FCC and IC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated with minimum distance
20cm between the radiator and your body. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Le terme «IC:» avant le numéro de certification radio signifie seulement que les spécifications
techniques d’Industrie Canada ont été respectées.
Cet appareil est conforme à FCC et IC l’exposition aux rayonnements limites fixées pour un envi-
ronnement non contrôlé. Cet appareil doit être installé et utilisé avec une distance minimale de 20 cm
entre le radiateur et votre corps. Cet transmetteur ne doit pas être co-situé ou opérant en liaison avec
toute autre antenne ou transmetteur.
This device has been designed to operate with the antennas listed below, and having a maximum gain of
[x] dB. Antennas not included in this list or having a gain greater than [x] dB are strictly prohibited for
use with this device. The required antenna impedance is 50 ohms.
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2)
this device must accept any interference, including interference that may cause undesired operation of
the device.
To reduce potential radio interference to other users, the antenna type and its gain should be so chosen
that the equivalent isotropically radiated power (e.i.r.p.) is not more than that permitted for successful
communication.
Thank you for your purchase of the Klipsch WA-2 Wireless Subwoofer Kit!
The WA-2 will only operate with select Klipsch, Energy, Mirage and Jamo brand subwoofers that have
a “WA Port” input. The WA-2 is a 2.4 GHz product designed to wirelessly transmit a signal up to a 50
foot radius.
Packing List:
1. Transmitter
2. Receiver
3. Power supply
4. Audio cable
5. Velcro strips
6. This Owner’s Manual
Setup:
1. Decide where the subwoofer will go (refer to your subwoofer owner’s manual).
2. Most receivers (and pre-amplifiers) have a line level subwoofer output labeled Subwoofer Pre Out,
Sub Out, SW Out, etc. If you have this, connect one end of the supplied audio cable to it and connect
the other end of the cable into WA-2 transmitter input ‘C’ . In absence of a subwoofer output connect
Left and Right channel Pre-Amp outputs from your receiver (if provided) to ‘C’ and ‘B’ inputs on the
transmitter.
3. Connect the cable from the WA-2 receiver to the “WA Port” on the back of the
subwoofer. Carefully match the 4 pins of the cable to the corresponding 4 holes on the
WA Port and gently push in until connected. Improper pin alignment can result in damage
to the connector.
4. Plug supplied power supply cable into ‘E’ on the WA-2 transmitter and plug other end into an AC wall
outlet.
C A U T I O N
RISK OF ELECTRIC SHOCK.
DO NOT OPEN.
WARNING: Do Not Open! Risk of Electrical Shock. Voltages in this
equipment are hazardous to life. No user-serviceable parts inside. Refer
all servicing to qualified service personnel.
5. Check to make sure Gain Switch ‘A’ is in middle position (0dB). This position best matches the
output voltage of most receivers and processors.
6. Turn receiver/pre-amplifier on.
7. Turn subwoofer to “On” or “Auto On” position.
8. The WA-2 transmitter and receiver should be automatically “paired”with their red LED’s ‘D’ on
solid and the subwoofer should now be operational.
9. You can use the supplied Velcro strips to attach the WA-2 receiver to the back of the subwoofer.
Some subwoofers have two screws on back that the receiver attaches to.
TROUBLESHOOTING:
- If the subwoofer does not operate and the red LED’s ‘D’ are flashing on the WA-2 transmitter and
receiver, a simple “pairing” is needed. Push and hold in button ‘F’ on the transmitter while pushing
and holding button ‘G’ on the receiver and keep pushed until both LED’s stop flashing and glow solid
(approximately 5 seconds).
- Since the WA-2 is a wireless device it may encounter RF interference from other wireless
devices in the same area. If there is difficulty “pairing” the transmitter and receiver, or their signal
connection “fades”, you may need to move them closer together and/or farther away from other
“wireless” products.
- If you do not get a signal, or get a low signal level from the subwoofer, make sure the subwoofer
out level control on your surround receiver is set correctly (usually at the halfway point sometimes
labeled “0dB”). If your subwoofer out level on your surround receiver is correct, and you have
adjusted the subwoofer volume level and the signal is still too low, move the gain control ‘A’ to the
right (+12dB) to increase the signal to the subwoofer. If the signal is too high, move the gain control
to the left (-12dB) to reduce signal strength.

Product specificaties

Merk: Energy
Categorie: Subwoofer
Model: ESW-M8

Heb je hulp nodig?

Als je hulp nodig hebt met Energy ESW-M8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Subwoofer Energy

Energy

Energy Power 12 Handleiding

17 Augustus 2023
Energy

Energy ESW-C8 Handleiding

17 Augustus 2023
Energy

Energy ESW-M8 Handleiding

17 Augustus 2023
Energy

Energy ESW-M6 Handleiding

17 Augustus 2023

Handleiding Subwoofer

Nieuwste handleidingen voor Subwoofer

Pioneer

Pioneer TS-A25S4 Handleiding

13 December 2024
Pioneer

Pioneer TS-A30S4 Handleiding

13 December 2024
Pioneer

Pioneer TS-A120S4E Handleiding

13 December 2024
JBL

JBL Power P1022 Handleiding

12 December 2024
JBL

JBL Power P1222 Handleiding

12 December 2024
ButtKicker

ButtKicker BK-LFE Handleiding

10 December 2024
Infinity

Infinity TSS-SUB750 Handleiding

9 December 2024
Infinity

Infinity TSS-SUB4000 Handleiding

9 December 2024
Infinity

Infinity Reference SUB R12 Handleiding

9 December 2024
AudioSource

AudioSource PSW110 Handleiding

9 December 2024