EMOS KT2244 Handleiding

EMOS Niet gecategoriseerd KT2244

Lees hieronder de 📖 handleiding in het Nederlandse voor EMOS KT2244 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 32 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

Beta400

GB TILT WALL MOUNT

CZ NAKLÁPĚCÍ DRŽÁK

SK NAKLÁPACÍ DRŽIAK

PL UCHWYT PRZECHYLNY

HTILT FALI TARTÓ

SLO

NASTAVLJIVO DRŽALO

DKLAPPBARER HALTER

UA КРОНШТЕЙН НАХИЛЬНИЙ

RO SUPORT RABATABIL

www.emos.cz

Beta400-manual KT2244 0-0-0-K

EMOS spol. s r. o., cz

TV Wall Mount Installation Instructions

Caution:

1. It is recommended for this product to be installed by at least two persons, of

which at least one person should be physically t enough to handle heavy

loads and technically skilled.

2. Before installing, please read this manual and make sure that there are no

electrical cords, gas or water pipes in the place designated for mounting the

holder.

3. We are not responsible for any damage incurred during installation, improper

installation or subsequent use.

4. If in doubt, contact your nearest dealer and ask for assistance with installation.

5. For installation it is necessary to use safe and appropriate tools. Disregarding

the instructions may cause property damage or injury.

6. If you intend to remove the TV from the wall, always make sure all electrical

cords are unplugged.

7. If you are unsure of your wall load, select adierent location for your installation

or carrying capacity and increase the strength of the wall with renovation.

8. The product can be installed only for at screen televisions or televisions

containing mounting holes and have aat back wall. To ensure that this holder

is compatible with your TV search for acompatible holder on the following

website www.emos.eu/DRTV

Tools necessary for installation (not included):

Philips Head Screw Driver

Electric or Portable Drill

Drill bit with 10 mm in Diameter (for Wood, Concrete, or as needed)

Plaster Board or Chipboard Anchors (as needed)

Pencil

Level (if not included)

Included:

Picture Type of Installation Material Pieces

A Anchor 10/50mm 4

B Wall Anchor Bolt 8/63mm 4

C Magnetic Level 1

D Anchor Bolt 4/12mm 4

E Anchor Bolt 4/22mm 4

H Anchor Bolt 6/12mm 4

I Anchor Bolt 6/22mm 4

J Anchor Bolt 8/15mm 4

K Anchor Bolt 8/30mm 4

L Screw Pads 4.5/10mm 4

N Screw Pads 6.3/14mm 4

O Rubber Gasket 15*8/15mm 4

Prior to every installation, remove the entire contents of the package and carefully

lay-out all its parts.

Diagram:

Wall Piece

Mounting Rail

Locking Laces Screws

Attaching the Wall Mount:

Carefully consider the location of your TV screen. To install the wall mount it is

necessary to drill into the wall. It is advisable to nd the position of mounting holes

on the back of your TV and mark their approximate position on the wall. Given

the construction of the wall mount you can then determine the position of the

so-called “wall piece”.

Once you are sure of the place to position your TV and the “wall piece”, take the “wall

piece” (part of the wall mount used to attach to your wall) and with the help of alevel

measure its exact position on the wall. In the opening or openings draw aposition of

anchor bolts on the wall with apencil (B). The number of bolts is at most types of wall

mounts random (the more the better), but mostly 4 anchors are sucient enough.

Take adrill and drill holes deep and wide enough to accommodate the anchors.

Hammer the anchors into the wall and make sure it is fully embedded and xed

in the wall. (If it easily falls out, it is possible that the drill hole is too big and the

anchor bolt is not big enough to stay in the wall – repeat the boring with adrill with

corresponding diameter).

Grasp the wall piece and attach it to the desired location. Attach it to the wall

with anchor bolts and tighten the screws suciently. Mounting of the wall piece

is completed.

NOTE: It is not recommended to install the mount straight on plasterboard walls.

Should you still insist on the installation, we recommend consulting a building

expert rst. You must also use astud detector and special anchors for plasterboard.

If the width of studs supporting the deployment of plasterboard wall is larger than

the width of the wall piece, try to x the wall piece in its centre with the help of

atapping screw into the metal post.

Mounting the TV:

The second part of the mount, the so-called “mounting rail“ is to be attached to the

television. Prior to the installation, it is recommended to rst take the rail and try to

attach it to the already mounted wall piece. This way you can try out the way it is

possible to attach your television to this wall mount or remove it.

Before attaching the rail, rst verify the diameter of screws securing the mounting

holes ready on the back of the TV (usually 4, 5, 6 a8 mm in diameter –these mounting

screws are included, if not otherwise). Mounting screws are provided in two lengths.

To select the proper screw length try to the screw it in the mounting screw hole so

there is remaining margin of 3-5 mm (CAUTION: never tighten with power – it can

cause damage to your television). If there is more space left, it is necessary to use

multiple pads or arubber gasket. It is usually used with longer types of screws (in

case you need agreater distance from the wall to manipulate with cables).To ensure

maximum capacity of the wall mount and prevent deformation of the wall mount it

is necessary to select appropriate types of mounting screws so that the mounting

screws are xed in the holes enough and threads are not exposed (leverage eect

on the mounting hole of the TV and the mount rail can occur).

Lace Locking Mechanism Quick lock:

To release the wall mount and the TV use locking laces. When installing, always leave

them hanging loose between the wall and the TV and adjust their length so that

you can easily nd it with your hand at the bottom of the part of the screen. When

attaching the mount you will hear aclick – this means that the mechanism is locked.

To unlock it it is necessary to slightly divert the bottom part of the screen away from

the wall and at the same time pull both laces downwards, while in the end keep slowly

pushing the TV upward. Then you can release the laces and freely manipulate the TV.

Disposal of products at the end of lifetime:

The represented symbol on the product or package means the product shall not

be treated as domestic waste. Hand over the product to the specied location for

recycling electric and electronic equipment. Prevent negative impacts on human

health and the environment by properly recycling your product. Recycling contri-

butes to preserving natural resources. For more information on the recycling of this

product, refer to your local authority, domestic waste processing organization or

store, where you purchased the product.

CE conformity declaration

We declare under our sole responsibility that Beta400 has been found in compliance

with essential protective requirements and objectives of EU directive.This declaration

loses validity with unauthorized changes of this product.

We do not take responsibility for damages caused during transport, by incorrect use

or achange or modication of any part of the product.

Návod kinstalaci nástěnného držáku TV

Upozornění:

1. Doporučujeme, aby tento výrobek byl instalován nejméně dvěma osobami,

znichž nejméně jedna osoba by měla být dostatečně fyzicky vybavená pro

práci stěžkými břemeny atechnicky zručná.

2. Před instalací si pozorně přečtěte tento návod kpoužití apřesvědčte se, že

vmístě požadovaného připevnění držáku se nenachází žádné elektrické kabely,

plynové či vodovodní trubky.

3. Neodpovídáme za žádné škody způsobené při instalaci, špatnou instalací, nebo

následným používáním.

4. Vpřípadě jakýchkoliv pochybností kontaktujte vašeho nejbližšího specializo-

vaného prodejce apožádejte ho opomoc při instalaci.

5. Kinstalaci je nezbytné použít bezpečné avhodné nářadí. Vopačném případě

může dojít kpoškození majetku či zdraví osob.

6. Pokud hodláte televizi ze stěny sundat, předtím pro jistotu vždy odpojte

všechny přívodní kabely.

7. Pokud si nejste jisti nosností vaší stěny, vyberte pro instalaci jiné místo, nebo

nosnost apevnost stěny zvyšte stavební úpravou.

8. Výrobek je možno instalovat pouze pro ploché TV nebo TV obsahující mon-

tážní otvory adisponují plochou zadní stěnou. Pro ujištění že tento držák je

použitelný pro Váš typ TV vyhledejte kompatibilní držák kvaší TV na adrese

www.emos.eu/DRTV

Nářadí potřebné kinstalaci (není součástí balení):

Křížový šroubovák

Elektrická nebo ruční vrtačka

Vrták sprůměrem 10 mm (do betonu, či dřeva dle potřeby)

Hmoždinky do sádrokartonu či dřevo třísky (dle potřeby)

Psací tužka

Vodováha (pokud není součástí balení)

Součást balení:

Obrázek Typ instalačního materiálu Počet

kusů

A Hmoždinka 10/50mm 4

B Kotvící šroub do zdi 8/63mm 4

C Magnetická vodováha 1

D Připevňující šroub 4/12mm 4

E Připevňující šroub 4/22mm 4

H Připevňující šroub 6/12mm 4

Před každou instalací vyjměte celý obsah balení apečlivě si rozložte jeho jed-

notlivé části.

Nákres:

Stěnová patice

Lyžiny držáku

Fixační šňůrky

I Připevňující šroub 6/22mm 4

J Připevňující šroub 8/15mm 4

K Připevňující šroub 8/30mm 4

L Podložky pro šrouby 4,5/10mm 4

N Podložky pro šrouby 6,3/14mm 4

O Gumová vložka 15*8/15mm 4

Product specificaties

Merk:	EMOS
Categorie:	Niet gecategoriseerd
Model:	KT2244
Kleur van het product:	Zwart
Breedte:	470 mm
Hoogte:	220 mm
Type verpakking:	Doos
Montagewijze:	Muur
Maximale gewichtscapaciteit:	40 kg
Draaien:	Nee
Montage interface compatibiliteit (min):	200 x 200 mm
Montage interface compatibiliteit (max):	400 x 400 mm
Aantal displays ondersteund:	1
Bereik kantelhoek:	-10 - 0 °
Maximale schermgrootte:	55 "
Minimale schermgrootte:	32 "
Afstand tot de muur (max.):	25 mm
Diepte (max):	20 mm
kantel aanpassingen:	Ja