Emko ESM-3711-HN Handleiding
Emko
Temperatuurregelaar
ESM-3711-HN
Lees hieronder de 📖 handleiding in het Nederlandse voor Emko ESM-3711-HN (30 pagina's) in de categorie Temperatuurregelaar. Deze handleiding was nuttig voor 61 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/30
ESM- 77x35 DIN Size Heating Controller3711-H
ESM- 77 x 35 DIN3711-H Size
Digital, ON / OFF Temperature Controller
Instruction Manual. ENG ESM-3711-H 02 V01 07/08
- 3 Digits display
- PTC Input or,
J type Thermocouple Input or,
K type Thermocouple Input or,
2-Wire PT 100 Input or,
2-Wire PT 1000 Input (It must be determined in order)
- ON/OFF temperature control
- Adjustable temperature offset
- Set value low limit and set value high limit boundaries
- Relay or SSR driver output
- Adjustable cooking time from front panel
- Temperature control with manual heating function
- Alarm parameters
- Adjustable internal buzzer according to cooking time , probe
defect and alarm status
- Button protection
- Password protection for programming section
- Digital Input (Cooking time start/stop input)
- Temperature control according to the cooking time (Timer)
- User can select to start cooking time (Timer) when temperature
reaches to the set value
Internal Buz ze r
ABOUT INSTRUCTION MANUAL
2
Instruction manual of ESM-3711-H Temperature Controller consists of two main sections.
Explanation of these sections are below. Also, there are other sections which include order
information and technical specifications of the device. All titles and page numbers in instruction
manual are in section.User can reach to any title with section number.
In this section, physical dimensions of the device, panel mounting, electrical wiring,
physical and electrical installation of the device to the system are explained.
Also in these sections, there are warnings to prevent serious injury while doing the
physical and electrical mounting or using the device.
Explanation of the symbols which are used in these sections are given below.
“CONTENTS”
Installation:
Operation and Parameters:
In this section user interface of the device, accessing to the parameters, description of the
parameters are explained.
a
c
i
This symbol is used to determine the dangerous situations as a result of an electric
shock.User must pay attention to these warnings definitely.
This symbol is used for safety warnings. User must pay attention to these
warnings.
This symbol is used to determine the important notes about functions and usage of
the device.
1.PREFACE............................................................................................................................................
1.1 GENERAL SPECIFICATIONS
1.2 ORDERING INFORMATION
1.3 WARRANTY
1.4 MAINTENANCE
2.1 GENERAL DESCRIPTION
2.2 FRONT VIEW AND DIMENSIONS OF ESM-3711-H TEMPERATURE CONTROLLER
2.3 PANEL CUT-OUT
2.4 ENVIRONMENTAL RATINGS
2.5 PANEL MOUNTING
2.6 INSTALLATION FIXING CLAMP
2.7 REMOVING FROM THE PANEL
3.1 TERMINAL LAYOUT AND CONNECTION INSTRUCTIONS
3.2 ELECTRICAL WIRING DIAGRAM
3.3 VIEW OF THE DEVICE LABEL
3.5 TEMPERATURE INPUT SENSOR CONNECTION
3.5.1
3.5.2
3.5.3
3.6 GALVANIC ISOLATION TEST VALUES OF ESM-3711-H TEMPERATURE CONTROLLER
3.7 OUTPUT CONNECTIONS
3.7.1 RELAY OUTPUT CONNECTION
3.7.2 SSR DRIVER OUTPUT CONNECTION
4.2 CHANGING AND SAVING SET VALUE
4.3
4.4 PROGRAMMING MODE PARAMETER LIST
4.5
4.5.1
4.5.2
4.6 OPERATION GRAPHICS OF ESM-3711-H HEATING CONTROLLER
4.7 EASY ACCESS DIAGRAM OF PROGRAMMING MODE PARAMETERS
4.8 ENTERING TO THE PROGRAMMING MODE, CHANGING AND SAVING PARAMETERS
2.INSTALLATION....................................................................................................................................
3.ELECTRICAL WIRINGS......................................................................................................................
4.FRONT PANEL DEFINITION AND ACCESSING TO THE MENUS....................................................
5.FAILURE MESSAGES IN ESM- HEATING CONTROLLER....................................................
6.SPECIFICATIONS................................................................................................................................
3711-H
3.4 SUPPLY VOLTAGE INPUT CONNECTION OF THE DEVICE
TC (THERMOCOUPLE) CONNECTION
PTC CONNECTION
PT-100 AND PT-1000 CONNECTION
4.1 OBSERVATION OF SOFTWARE REVISION ON THE DISPLAYS
CHANGING AND SAVING COOKING TIME (TIMER) PARAMETER VALUE
COOKING TIME (TIMER) ON/OFF OPERATION
COOKING TIME (TIMER) ON/OFF OPERATION WITH COOKING BUTTON
COOKING TIME (TIMER) ON/OFF OPERATION WITH COOKING TIME START/STOP
INPUT
Contents
Page 5
Page 30
Page 19
Page 12
Page 7
Page 29
3
Product specificaties
| Merk: | Emko |
| Categorie: | Temperatuurregelaar |
| Model: | ESM-3711-HN |
Heb je hulp nodig?
Als je hulp nodig hebt met Emko ESM-3711-HN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Temperatuurregelaar Emko
26 Februari 2024
26 Februari 2024
26 Februari 2024
26 Februari 2024
27 November 2023
27 November 2023
27 November 2023
27 November 2023
27 November 2023
1 Juli 2023
Handleiding Temperatuurregelaar
- Temperatuurregelaar Panasonic
- Temperatuurregelaar AEG
- Temperatuurregelaar Honeywell
- Temperatuurregelaar ACV
- Temperatuurregelaar Astralpool
- Temperatuurregelaar Berker
- Temperatuurregelaar Bulex
- Temperatuurregelaar Davis
- Temperatuurregelaar Dimplex
- Temperatuurregelaar Fluke
- Temperatuurregelaar Hager
- Temperatuurregelaar Kathrein
- Temperatuurregelaar Techno Line
- Temperatuurregelaar Technoline
- Temperatuurregelaar Ventus
- Temperatuurregelaar Voltcraft
- Temperatuurregelaar Wachendorff
- Temperatuurregelaar Ygnis
- Temperatuurregelaar Jung
- Temperatuurregelaar Opticlimate
- Temperatuurregelaar Cocraft
- Temperatuurregelaar IFM
- Temperatuurregelaar Inkbird
- Temperatuurregelaar Carel
- Temperatuurregelaar Ziehl
- Temperatuurregelaar SRS
- Temperatuurregelaar Jumo
Nieuwste handleidingen voor Temperatuurregelaar
5 December 2024
5 December 2024
2 December 2024
30 November 2024
30 November 2024
30 November 2024
18 November 2024
18 November 2024
18 November 2024
18 November 2024