Emko CHANNEL8A-N Handleiding


Lees hieronder de šŸ“– handleiding in het Nederlandse voor Emko CHANNEL8A-N (4 pagina's) in de categorie Temperatuurregelaar. Deze handleiding was nuttig voor 60 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
ENGī˜ ī˜ CHANNEL8A-Nī˜ 01ī˜ V00ī˜ 03/17
CHANNEL8A-N
8ī˜ CHANNEL ANALOGī˜ SCANNER
96ī˜ xī˜ 96ī˜ DINī˜ 1/4
12ī˜ Ā±ī˜ 1ī˜ mmī˜ /ī˜ 0.47ī˜ inch 84ī˜ mmī˜ /ī˜ 3.31ī˜ inch
ī˜ 15 0.59ī˜ inchmmī˜ /
92mm/3.62ī˜ inch
92mm/3.62ī˜ inch
129mm/5.08ī˜ inch(min)
129mm/5.08ī˜ inch(min)
320ī˜ xī˜ 240ī˜ Pixel
TFT LCD
Standart
Function
Buttons
MENU BUTTON
Used to access Menu page.
ENTER BUTTON
Used to go in to selected page, to make parameter's cell
available toī˜ change and to confirm parameterā€™s change.
AUTO BUTTON
Used to auto-scan pages.
BACK BUTTON
Used to go back to previous menu and to cancel
parameter's change.
UP BUTTON
Used to go up in menus and lists and also used to increase
parameter's value.
LEFTī˜ BUTTON
Usedī˜ toī˜ goī˜ leftī˜ inī˜ menus.
DOWNī˜ BUTTON
Usedī˜ toī˜ goī˜ downinī˜ menusī˜ andī˜ listsī˜ andī˜ alsoī˜ usedī˜ to
decreaseī˜ parameter'sī˜ value.
RIGHTī˜ BUTTON
Usedī˜ toī˜ goī˜ rightī˜ inī˜ menus.
F4
F1 F2 F3
DELETEī˜ BUTTON
Usedī˜ toī˜ eraseī˜ logsī˜ onī˜ theī˜ screen.
SETTINGS
LOGS
ADVANCE
SETTINGS
LANGUAGE
CHANNEL8A-Nī˜ 8ī˜ Channel Analogī˜ Scanner
-ī˜ 320ī˜ xī˜ 240ī˜ pixelī˜ TFTī˜ LCDī˜ display
-ī˜ 8 Analogī˜ inputs
-ī˜ ON-OFFī˜ control
-ī˜ Relayī˜ orī˜ (pnp ā€œsourceā€)ī˜ transistorī˜ output
-ī˜ Sensorī˜ errorī˜ detection
- Adjustableī˜ temperatureī˜ offset
-ī˜ 3ī˜ Differentī˜ alarmī˜ andī˜ pre-alarmī˜ typesī˜ forī˜ eachī˜ channel
(High,ī˜ Lowī˜ andī˜ Band Alarms)
-ī˜ Userī˜ definedī˜ channelī˜ labels
-ī˜ Displayī˜ scanī˜ modes
-ī˜ Operatingī˜ withī˜ Realī˜ Timeī˜ Clockī˜ (RTC)
-ī˜ ModBusī˜ RTUī˜ communicationī˜ protocol
(RS-232,ī˜ RS-485ī˜ andī˜ Ethernetī˜ communication)
-ī˜ Dataī˜ Loggingī˜ toī˜ USBī˜ Flashī˜ Memory
- Adjustableī˜ dataī˜ loggingī˜ timeī˜ interval
-ī˜ Passwordī˜ protectionī˜ forī˜ programmingī˜ mode
CHANNEL8A-N series 8 channel analog scanner devices are designed
for measuring and logging temperature. They can be used in many
applications with their, alarm outputs, selectable alarm functions, RS-
232 / RS-485 / Ethernet / USB communications.
SPECIFICATIONS
INPUT
Analogī˜ Inputsī˜ :
Accuracyī˜ :
Samplingī˜ Timeī˜ :
OUTPUT
Relayī˜ :
DISPLAY
LCDī˜ Displayī˜ :
POWERī˜ SUPPLY
ENVIRONMENTAL RATINGS
Operatingī˜ Temperatureī˜ :
Humidityī˜ :
Protectionī˜ Classī˜ :
PHYSICAL SPECIFICATIONS
Weightī˜ :
Dimension :
Panel Cut-Out :
0-20mA /ī˜ 4-2ī˜ mA andī˜ 0-10VDC Analogue
Ā±ī˜ 0.25%ī˜ ofī˜ fullī˜ scale
400ī˜ ms
ax.1A@24V
320x240
0...50Ā°C
0-90%RHī˜ (noneī˜ condensing)
IP65ī˜ atī˜ front,ī˜ IP20ī˜ atī˜ rear
0ī˜ gr.
96 x 96 mm, Depth:96 mm
92 x 92 mm
W
W
40
Resolutionī˜ :
Inputī˜ Ressistanceī˜ :
Transistorī˜ :
14ī˜ Bits
100 forī˜ 0-20mA inputī˜ and
68k forī˜ 0-10Vī˜ input
Resistiveī˜ Loadī˜ 5A@250V
(Electricalī˜ Lifeī˜ :ī˜ 100.000ī˜ operationī˜ (Fullī˜ Load)
PNP(source)ī˜ typeī˜ transistorī˜ outputī˜ (M )
pixel TFT LCD
100ī˜ -ī˜ 240ī˜ V (-%15ī˜ /ī˜ +%10)ī˜ 50/60ī˜ Hz.ī˜ ī˜ 7VA
24ī˜ V (-%15ī˜ /ī˜ +%10)ī˜ 50/60ī˜ Hz.ī˜ ī˜ 7VA
24ī˜ V (-%15ī˜ /ī˜ +%10)ī˜ ī˜ 7W
(Itī˜ mustī˜ beī˜ determinedī˜ inī˜ order.)
V
Z
V
V
Z
Electricalī˜ Wiringī˜ Diagram
Deviceī˜ withī˜ Relayī˜ Outputs
RSī˜ 232
COMMUNICATION
5ī˜ xī˜ 5A@250V
COMMON-1
COMMON-2
16 21 22 23 24 25 26 27 28 29 3017 18 19 20
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
CH-1 ALARM
OUTPUT
CH-
OUTPUT
2 ALARM
CH-
OUTPUT
3 ALARM
CH-
OUTPUT
4 ALARM
CH-
OUTPUT
5 ALARM
CH-
OUTPUT
6 ALARM
CH-
OUTPUT
7 ALARM
CH-
OUTPUT
8 ALARM
GENERAL ALR.
OUTPUT
GENERAL PRE-ALR.
OUTPUT
5ī˜ xī˜ 5A@250V
USBī˜ 2.0
COMMUNICATION
ETHERNET
OR
RS485
COMMUNICATION
CH-1CH-2CH-3CH-4CH-5CH-6CH-7CH-8
100...240Vī˜ ī˜ ī˜ ī˜ ī˜ -ī˜ %15;+%10)ī˜ 50/60Hzī˜ 7VA
24Vī˜ ī˜ ī˜ ī˜ ī˜ ī˜ (-%15;+%10)ī˜ 50/60Hzī˜ 7VA
24Vī˜ ī˜ ī˜ ī˜ ī˜ ī˜ (-%15;+%10)ī˜ 7W
L
(+)
N
(-)
Deviceī˜ withī˜ Transistorī˜ Outputs
RSī˜ 232
COMMUNICATION
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
USBī˜ 2.0
COMMUNICATION
ETHERNET
OR
RS485
COMMUNICATION
100...240Vī˜ ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ (-ī˜ %15;+%10)ī˜ 50/60Hzī˜ 7VA
24Vī˜ ī˜ ī˜ ī˜ ī˜ ī˜ (-%15;+%10)ī˜ 50/60Hzī˜ 7VA
24Vī˜ ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ (-%15;+%10)ī˜ 7W
L
(+)
N
(-)
iRS485, Ethernet and USB communications are optional
16 21 22 23 24 25 26 27 28 29 3017 18 19 20
CH-1 ALARM
OUTPUT
CH-
OUTPUT
2 ALARM
CH-
OUTPUT
3 ALARM
CH-
OUTPUT
4 ALARM
CH-
OUTPUT
5 ALARM
CH-
OUTPUT
6 ALARM
CH-
OUTPUT
7 ALARM
CH-
OUTPUT
8 ALARM
GENERAL ALR.
OUTPUT
GENEAL PRE- ALR.
OUTPUT
10ī˜ xī˜ 1A@24V
TRANSISTORī˜ OUTPUTS
POWERī˜ SUPPLY
24Vī˜ ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ Ā±%15
iRS485, Ethernet and USB communications are optional
Relayī˜ Outputs
(Alarmī˜ Outputsī˜ for
Channelsī˜ 6ī˜ toī˜ 8,
General Alarmī˜ Outputī˜ and
Generalī˜ Pre-Alarmī˜ Outputī˜ )
CHī˜ =ī˜ CHANNEL
Powerī˜ Supplyī˜ Input
(Itī˜ mustī˜ beī˜ determinedī˜ inī˜ order.)
Common1 Common2
Relayī˜ Outputs
(Alarmī˜ Outputsī˜ for
Channelsī˜ 1ī˜ toī˜ 5)
Powerī˜ Supplyī˜ Input
(Itī˜ mustī˜ beī˜ determinedī˜ inī˜ order.)
Transistorī˜ Outputs
(Alarmī˜ Outputsī˜ for
Channelsī˜ 1ī˜ toī˜ 8,
General Alarmī˜ Outputī˜ and
Generalī˜ Pre-Alarmī˜ Outputī˜ )
CHī˜ =ī˜ CHANNEL
Maximum
CHANNEL8A-NFrontī˜ Viewī˜ andī˜ Dimensionsī˜ of
Panelī˜ Cut-Out
1-Before mounting the device
in your panel, make sure that
the cut-out is of the right size.
2-Check front panel gasket
position
3-Insert the device through the
cut-out. If the mounting clamps
are on the unit, put out them
before inserting the unit to the
panel.
Panelī˜ Mounting
Installationī˜ Fixingī˜ Clamp
The unit is designed for panel
mounting.
1-Insert the unit in the panel
cut-out from the front side.
2- Insert the mounting clamps
to the holes that located top
and bottom sides of device and
screw up the fixing screws until
the unit completely immobile
within the panel.
Removingī˜ fromī˜ theī˜ Panel
1-Loosen the screws.
2-Pull mounting clamps from
top and bottom fixing sockets.
3-Pull the unit through the
front side of the panel
Definitionī˜ ofī˜ Frontī˜ Panel
AGND
Processī˜ Inputs
(4-20mA /ī˜ 0-20mA)
(0-10ī˜ V)
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0
-10VZ
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
AGND
Processī˜ Inputs
(4-20mA /ī˜ 0-20mA)
(0-10ī˜ V)
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
ı
+
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10 VZ
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10VZ
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
0-20mA Z
0-10V Z
4-20mA Z
CH-1CH-2CH-3CH-4CH-5CH-6CH-7CH-8
96ī˜ mmī˜ /ī˜ 3.78ī˜ inch
96ī˜ mmī˜ /ī˜ 3.78ī˜ inch
F1 F2 F3 F4
A
1
2
3
F1 F2 F 3 F4
A
1
2
F1 F2 F 3 F4
A
F4F1 F2 F3
A
3
1
2
F1 F2 F 3 F4
A
MAINī˜ OPERATIONī˜ SCREEN
MAINī˜ OPERATIONī˜ (CHANNEL-1ī˜ SCREEN)
i
i
i
MENUī˜ SCREEN
OPERATORī˜ PARAMETERS
PASSWORDī˜ SCREEN
Pressī˜ F1ī˜ orī˜ F2ī˜ directionī˜ buttons
toī˜ moveī˜ toī˜ theī˜ Settingsī˜ tab.
Whenī˜ theī˜ F1ī˜ menuī˜ buttonī˜ isī˜ pressed
whileī˜ theī˜ mainī˜ screenī˜ isī˜ onī˜ theī˜ page,ī˜ the
menuī˜ pageī˜ isī˜ displayed.
PARAMETERS
CHANGE
PARAMETERS
CHANGE
OPERATORī˜ PARAMETERS
(CHANNEL-1ī˜ PARAMETERS)
Pressī˜ F3ī˜ button.ī˜ Ifī˜ password
isī˜ differentī˜ fromī˜ 0,ī˜ password
screenī˜ opens.
Enterī˜ theī˜ passwordī˜ valueī˜ using
theī˜ F1ī˜ andī˜ F2ī˜ buttons.
Confirmī˜ theī˜ charactersī˜ oneī˜ by
oneī˜ byī˜ pressingī˜ F3ī˜ button.
Onceī˜ youī˜ haveī˜ confirmedī˜ the
lastī˜ character,ī˜ youī˜ willī˜ proceed
toī˜ theī˜ operatorī˜ parameters
screen.
Pressī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ to
highlightī˜ theī˜ channelī˜ andī˜ pressī˜ theī˜ F3
button.
Selectī˜ theī˜ relevantī˜ parameter
withī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttons.
Pressī˜ theī˜ F3ī˜ buttonī˜ toī˜ select
theī˜ parameter.
Useī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ toī˜ change
theī˜ valueī˜ ofī˜ theī˜ parameter.
Pressī˜ theī˜ F3ī˜ buttonī˜ toī˜ save
theī˜ parameterī˜ value.
DEVICEī˜ SETTINGS
(Rs485ī˜ SETTINGS)
DEVICEī˜ SETTINGS
(USBī˜ SETTINGS)
DEVICEī˜ SETTINGS
(ETHERNETī˜ SETTINGS)
DEVICEī˜ SETTINGS
(DATEī˜ TIMEī˜ SETTINGS)
Withī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ youī˜ can
selectī˜ andī˜ changeī˜ theī˜ USB
parameters.ī˜ Useī˜ theī˜ F3ī˜ buttonī˜ to
save.
Withī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ youī˜ can
selectī˜ andī˜ changeī˜ theī˜ RS485
parameters.ī˜ Useī˜ theī˜ F3ī˜ buttonī˜ to
save.
Withī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ youī˜ can
selectī˜ andī˜ changeī˜ theī˜ ETHERNET
parameters.ī˜ Useī˜ theī˜ F3ī˜ buttonī˜ to
save.
Withī˜ theī˜ F3ī˜ buttonī˜ youī˜ canī˜ selectī˜ the
Dateī˜ and Timeī˜ parametersī˜ andī˜ you
canī˜ changeī˜ theī˜ valueī˜ withī˜ theī˜ F1,ī˜ F2
buttons.
i
i
i
Channelī˜ Number
Deviceī˜ Function
Buttons
Alarm Set
Alarm set value for selected channel is can be adjusted according to this parameter.
It can be adjust between -200 0
O O
C to +65 C.
Pre. Alarm Set
Pre- Alarm set value for selected channel is can be adjusted according to this
parameter. It can be adjust between -200 0
O O
C to +65 C.
i
F4F1 F2 F3
Channelī˜ Label
PreAlarmī˜ Status
Alarmī˜ Status
Channelsī˜ Names
Processī˜ Value
F4F1 F2 F3
F4F1 F2 F3
Alarmī˜ Messages
Channelī˜ Output
Status
Channelī˜ Number
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3
F1
F1 F2
F3
F1
F2
F3
F1
F2
F1
F2 F3
F1
F2
Operatorī˜ Passwordī˜ Change
Passwordī˜ forī˜ deviceī˜ isī˜ adjustedī˜ byī˜ thisī˜ parameter.Operator
DEVICEī˜ SETTINGS
(PASSWORDī˜ CHANGE)
Useī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ toī˜ change
theī˜ valueī˜ ofī˜ theī˜ parameter.ī˜ Confirmī˜ the
charactersī˜ oneī˜ byī˜ oneī˜ byī˜ pressingī˜ F3
button.
Useī˜ theī˜ F1ī˜ buttonī˜ toī˜ moveī˜ to
theī˜ "YES"ī˜ tabī˜ andī˜ pressī˜ theī˜ F3
button.ī˜ Inī˜ 1-3ī˜ secondsī˜ the
deviceī˜ willī˜ returnī˜ toī˜ factory
settings.
F4F1 F2 F3 F4F1 F2 F3
TECHNICIANī˜ PARAMETERS
(CONTROL PARAMETERS
TECHNICIANī˜ PARAMETERS
PASSWORDī˜ SCREEN
TECHNICIANī˜ PARAMETERS
PASSWORDī˜ SCREEN
TECHNICIANī˜ PARAMETERS
PASSWORDī˜ INPUTī˜ SCREEN
Pressī˜ F1ī˜ orī˜ F2ī˜ directionī˜ buttons
toī˜ moveī˜ toī˜ the Advanced
Settingsī˜ tab.
PARAMETERS
CHANGE
DEVICEī˜ SETTINGS
(RS232ī˜ SETTINGS)
Pressī˜ F3ī˜ button.ī˜ Ifī˜ password
isī˜ differentī˜ fromī˜ 0,ī˜ password
screenī˜ opens.
Enterī˜ theī˜ passwordī˜ valueī˜ using
theī˜ F1ī˜ andī˜ F2ī˜ buttons.
Confirmī˜ theī˜ charactersī˜ oneī˜ by
oneī˜ byī˜ pressingī˜ F3ī˜ button.
Onceī˜ youī˜ haveī˜ confirmedī˜ the
lastī˜ character,ī˜ youī˜ willī˜ proceed
toī˜ theī˜ operatorī˜ parameters
Useī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ toī˜ scrollī˜ to
theī˜ Controlī˜ parametersī˜ andī˜ pressī˜ the
F3ī˜ button.
Selectī˜ theī˜ relevantī˜ channelī˜ withī˜ theī˜ F1
andī˜ F2ī˜ buttons.
Pressī˜ theī˜ F3ī˜ buttonī˜ toī˜ select
theī˜ parameter.
Useī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ toī˜ change
theī˜ valueī˜ ofī˜ theī˜ parameter.ī˜ Pressī˜ the
F3ī˜ buttonī˜ toī˜ saveī˜ theī˜ parameterī˜ value.
Withī˜ theī˜ F1ī˜ andī˜ F2ī˜ buttonsī˜ you
canī˜ selectī˜ andī˜ changeī˜ theī˜ RS232
parameters.ī˜ Useī˜ theī˜ F3ī˜ buttonī˜ to
save.
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3 F4F1 F2 F3
F4F1 F2 F3F4F1 F2 F3
F1
F1 F2
F3
F1
F2
F3
F1
F2
F1
F2 F3
F3
F3
F3
F3
TECHNICIANī˜ PARAMETERS
(CHANNEL-1)
TECHNICIANī˜ PARAMETERS
(CHANNEL-1ī˜ PARAMETERS)
Mainī˜ Operationī˜ Screensī˜ Definetion Accessingī˜ toī˜ theī˜ Operatorī˜ Parameterī˜ Pages
Ifī˜ theī˜ displayī˜ typeī˜ parameterī˜ valueī˜ ī˜ Screenī˜ Typeī˜ =ī˜ MULTIPLE
If the display scan parameter value Screen Change = ENABLE, each main
operation screen is showing on LCD screen during time defined by Change
Time parameter value.
Ifī˜ theī˜ displayī˜ typeī˜ parameterī˜ valueī˜ ī˜ Screenī˜ Typeī˜ =ī˜ SINGLE
Channelī˜ Name
Processī˜ Value
MAINī˜ OPERATIONī˜ (CHANNEL-4ī˜ SCREEN)
Pressī˜ number
F2ī˜ orī˜ F3
buttonsī˜ for
accessingī˜ the
relevantī˜ channel
screen.
If the display scan parameter value Screen Change = ENABLE, each main
operation screen is showing on LCD screen during time defined by Change
Time(sec) parameter value
If more than one alarm messages is present, each alarm message is
showing on LCD screen during 1 second.
MAINī˜ OPERATIONī˜ SCREEN
OPERATORī˜ PARAMETERS
PASSWORDī˜ SCREEN
OPERATORī˜ PARAMETERS
PASSWORDī˜ INPUTī˜ SCREEN
OPERATORī˜ PARAMETERS
(CHANNEL-1)
OPERATORī˜ PARAMETERS
(CHANNEL-1ī˜ PARAMETERS)
Accessingī˜ toī˜ theī˜ Technicianī˜ Parameterī˜ Pages
Operatorī˜ Pagesī˜ Parametersī˜ Definetions
If no operation is performed for 20 seconds in operator parameters section,
device turns to main operation screen automatically.
If the device has a optional RS485 communication then RS 485 page is
observed, If the device has a optional USB communication then USB page is
observed.
If no operation is performed for 20 seconds in operator or technician
parameters section, device turns to main operation screen automatically.
If the device has a optional ETHERNET communication then ETHERNET
page is observed, otherwise this page is not observed.
MAINī˜ OPERATIONī˜ SCREEN
MENUī˜ SCREEN
Whenī˜ theī˜ F1ī˜ menuī˜ buttonī˜ isī˜ pressed
whileī˜ theī˜ mainī˜ screenī˜ isī˜ onī˜ theī˜ page,ī˜ the
menuī˜ pageī˜ isī˜ displayed.
DEVICEī˜ SETTINGS
(DEFAULTī˜ SETTINGS)
A
A
A
A A
A A
A A
A A
A A
A A
A A
AA
AA
A A
AA
AA
A A
A
Unitī˜ Select
Type of unit value is adjusted according to this parameter for selected channel which is
shown on display.The value of parameter C, Bar, Ph, %, mm, m.
O
Hysteresis
Hysteresis parameter value for Alarm and Pre-Alarm is can be adjusted by this
parameter. It can be adjust between -400 0
O O
C to +40 C.
Band Alarm
Bandwith for Band alarm is can be adjusted by this parameter value.
It can be adjust between -400 0
O O
C to +40 C.
Sensor Alarm
Sensor break alarm for selected channel is can be disable or enable by this parameter.
It can be adjust between 0 to 1. Parameter values;
0 = DISABLE
1 = ENABLE
Offset
Process offset value for selected channel is can be adjusted by this parameter.
It can be adjust between -50.0 0
O O
C to +50. C.
Controlī˜ Parameters-ī˜ Otherī˜ Parameters
Screen Type
Main operation screen type is adjusted by this parameter.
It can be adjust between 0 to 1. Parameter values;
0 = MULTIPLE
1 = SINGLE
Screen Change
It can be adjust between 0 to 1. Parameter values;
0 = DISABLE
1 = ENABLE
Display channel scanner mode is adjusted by this parameter.
Change Time(sec)
Display scan period is adjusted by this parameter. All main operation screen is
displayed during time defined by this parameter. It can be adjust between 1 to 3600
secs.
Baudrate
It can be adjust between 0 to 5. Parameter values;
0 = 4800 3 = 38400
1 = 9600 4 = 57600
2 = 19200 5 = 115200
Modbus communication baudrate for RS232 is can be adjusted by this parameter.
Parity
It can be adjust between 0 to 2. Parameter values;
0 = NONE
1 = ODD
2 = EVEN
Modbus communication parity bit for RS232 is can be adjusted by this parameter.
Stop Bit
It can be adjust between 1 to 2. Parameter values;
1 = 1 Stop bit
2 = 2 Stop bits
Modbus communication stop bit for RS232 is can be adjusted by this parameter.
Id
Modbus communication device ID for RS232 is can be adjusted by this parameter.
This parameter value is can be adjusted from 1 to 247.
File Name
USB file name for recording analogue values is can be adjusted by this parameter. File
name can be adjusted maximum 10 characters. Recording file on usb is csv formatā€œ ā€
and all data is seperated each other with tab. Example file format is explained below.
Label
When the analogue values are recorded on USB file, user can be defined label for this
recording. Label can be adjusted maximum 10 characters. Label are recorded at the
end of every lines of file.
Date Record
It can be adjust between 0 to 1. Parameter values;
0 = DISABLE
1 = ENABLE
When the analogue values are recorded on USB file, user can be save the recording
time on the file. Recording time is recorded at the beginning of every lines of file.
Record Time(sec)
It can be adjust between 0 to 3600 secs.
Record time interval is can be adjusted by this parameter. Analogue values are
recorded on USB file with this time interval. If
this parameter value is 0 usb recording is disabled.
Flash Memory ā€œUSB Flash Memory Stick Detected Testā€
Detection of the USB memory device being inserted is tested with this parameter.
When the USB memory device is plugged in, the message "OK" is displayed.
DHCP
It can be adjust between 0 to 1. Parameter Values;
0 = DHCP DISABLE
1 = DHCP ENABLE
DHCP is an automatic configuration protocol used on IP networks, If DHCP is enable,
device is adjust our ethernet communication configuration parameters (IP,
Netmask,Gateway) dynamicaly for your network system. If DHCP is disable, you must
adjust ethernet configuration parameters (IP, Netmask,Gateway) for your network
system.
Port No
Ethernet port number is can be adjusted by this parameter.
Netmask
Subnet mask for ethernet communication is can be adjusted by this parameter. If
DHCP is selected as a enable there is no need to adjust to this parameter, if DHCP is
selected as a disable then user must adjust this parameter according to the their own
network system.
Gateway
Gateway for ethernet communication is can be adjusted by this parameter. If DHCP is
selected as a enable there is no need to adjust to this parameter, if DHCP is selected as
a disable then user must adjust this parameter according to the their own network
system.
Ip No
IP address for ethernet communication is can be adjusted by this parameter. If DHCP
is selected as a enable there is no need to adjust to this parameter, if DHCP is selected
as a disable then user must adjust this parameter.
Channel Status
It can be adjust between 0 to 1. If parameter value
0 = DISABLE
1 = ENABLE
Channel is enabled and disabled by this parameter. If channel is selected as a disabled
this channel is can not be observed in main operation scren for single view mode,
channel alarm is not be controlled and analogue value for this channel is can not be
recording on USB file. ,
Channel Name ā€œ ā€Channels label definition
All channels have their own label, is displayed in main operation screen. channel labels is can
be adjusted by this parameter. Channel labels are can be adjusted maximum 10 characters.
Alarm Type
Alarm type for selected channel is can be adjusted according to this parameter.
It can be adjust between 0 to 2. Parameter values;
0 = LOW 1 = HIGH 2 = BAND
PreAlarm Type
Pre-Alarm type for selected channel is can be adjusted according to this parameter.
It can be adjust between 0 to 2. Parameter values;
0 = LOW 1 = HIGH 2 = BAND
BackLightOnLevel
Display backlight is can be controlled by this parameter value. It can be adjust
between 50 to 100.
BackLightOffLevel
CO mode for backlight; in case off selection no backlight . ThisE parameter is can be
adjusted from 1 to 100.
BackLightOffTime
Time for the access to ecomomic backlight mode. This parameter is can be adjusted
from 10 to 300.
Deviceī˜ Settingsī˜ -ī˜ RS-232ī˜ Settings
Deviceī˜ Settingsī˜ -ī˜ RS-485ī˜ Settings
Baudrate
It can be adjust between 0 to 5. Parameter values;
0 = 4800
1 = 9600
2 = 19200
3 = 38400
4 = 57600
5 = 115200
Modbus communication baudrate for RS485 is can be adjusted by this parameter.
Parity
It can be adjust between 0 to 2. Parameter values;
0 = NONE
1 = ODD
2 = EVEN
Modbus communication parity bit for Rs485 is can be adjusted by this parameter.
Stop Bit
It can be adjust between 1 to 2. Parameter values;
1 = 1 Stop bit
2 = 2 Stop bits
Modbus communication stop bit for Rs485 is can be adjusted by this parameter.
Id
Modbus communication device ID for Rs485 is can be adjusted by this parameter.
This parameter value is can be adjusted from 1 to 247.
Deviceī˜ Settingsī˜ -ī˜ USBī˜ Settings
Deviceī˜ Settingsī˜ -ī˜ ETHERNETī˜ Settings
TcpIp Selection
It can be adjust between 0 to 1.
0 = Modbus RTU Over TCP/IP
1 = Modbus RTU TCP/IP
TCP/IP Protocol is can be adjusted by this parameter.
Deviceī˜ Settingsī˜ -Defaultī˜ Settings
Thisī˜ sectionī˜ isī˜ usedī˜ toī˜ returnī˜ defaultī˜ settingsī˜ back.
Deviceī˜ Settingsī˜ -ī˜ Dateī˜ andī˜ Timeī˜ Settings
Date and Time for device is adjusted by this parameter.
Deviceī˜ Settingsī˜ -ī˜ Passwordī˜ Change
Technician Password for device is adjusted by this parameter.
Deviceī˜ Settingsī˜ -ī˜ Softwareī˜ Update
It allows you to update the device's software with a USB flash memory.
Logs
In this page, events logs are shown.
Languageī˜ Selection
Inī˜ thisī˜ page,ī˜ theī˜ languageī˜ isī˜ selectedī˜ forī˜ theī˜ device.
F4F1 F2 F3
F4F1 F2 F3
SET
HYS
BAND
=
=
=
Alarm or Pre-Alarm Set value
Hysteresis value forAlarm and Pre-Alarm output
Bandwidth for Band Alarm.
ON
OFF
Process Value
ON
OFF
Alarm
Output
Process Value
Alarm
Output
SET
HYS
SET
HYS
ON
OFF
Alarm
Output
Process Value
BandAlarm
LowAlarm
HighAlarm
Operationī˜ Graphicsī˜ of Alarmī˜ andī˜ Pre-Alarmī˜ Types
i
Modbus Addresses
Outputī˜ Status Addresses
Outputsī˜ Status Addresses Unit
CH-1 ALARMī˜ OUT Channel-1 Alarmī˜ Outputī˜ Status
Address
00001
-
CH-2 ALARMī˜ OUT Channel-2 Alarmī˜ Outputī˜ Status 00002
-
CH-3 ALARMī˜ OUT Channel-3 Alarmī˜ Outputī˜ Status 00003
-
CH-4 ALARMī˜ OUT Channel-4 Alarmī˜ Outputī˜ Status 00004
-
CH-5 ALARMī˜ OUT Channel-5 Alarmī˜ Outputī˜ Status 00005
-
CH-6 ALARMī˜ OUT Channel-6 Alarmī˜ Outputī˜ Status 00006
-
CH-7 ALARMī˜ OUT Channel-7 Alarmī˜ Outputī˜ Status 00007
-
CH-8 ALARMī˜ OUT Channel-8 Alarmī˜ Outputī˜ Status 00008
-
GEN. ALR.ī˜ OUT General Alarmī˜ Outputī˜ Status 00009
-
GEN.PRE.ALR.ī˜ OUT Generalī˜ Pre-alarmī˜ Outputī˜ Status 00010
-
Note-1: Outputs status are can be readed with modbus function-1 (read coils).
Device s response for modbus function-1 is always 2 byte data although the modbusā€™
function request less than 9 outputs port.
Processī˜ Values Addresses
Processī˜ Values Addresses Unit
CH-1ī˜ P.ī˜ VALUE Channel-1ī˜ Processī˜ Value
Address
30001
CH-2ī˜ P.ī˜ VALUE Channel-2ī˜ Processī˜ Value 30002
CH-3ī˜ P.ī˜ VALUE Channel-3ī˜ Processī˜ Value 30003
CH-4ī˜ P.ī˜ VALUE Channel-4ī˜ Processī˜ Value 30004
CH-5ī˜ P.ī˜ VALUE Channel-5ī˜ Processī˜ Value 30005
CH-6ī˜ P.ī˜ VALUE Channel-6ī˜ Processī˜ Value 30006
CH-7ī˜ P.ī˜ VALUE Channel-7ī˜ Processī˜ Value 30007
CH-8ī˜ P.ī˜ VALUE Channel-8ī˜ Processī˜ Value 30008
Note-2: Process values are can be readed with modbus function-4 (read input
register). Because of the process values are displayed on LCD screen with point, the
reading valuesī˜ from modbus is 10 times than the real values.
Parametersī˜ Modbus Addresses
Parameterī˜ Values Addresses Unit
CH-1ī˜ NAME Channel-1ī˜ Name
Address
42000ī˜ -ī˜ 42004
CH-2ī˜ NAME Channel-2ī˜ Name 42005ī˜ -ī˜ 42009String 42005ī˜ -ī˜ 42009
CH-3ī˜ NAME Channel-3ī˜ Name 42010ī˜ -ī˜ 42014
CH-4ī˜ NAME Channel-4ī˜ Name 42015ī˜ -ī˜ 42019
CH-5ī˜ NAME Channel-5ī˜ Name 42020ī˜ -ī˜ 42024
CH-6ī˜ NAME Channel-6ī˜ Name 42025ī˜ -ī˜ 42029
CH-7ī˜ NAME Channel-7ī˜ Name 42030ī˜ -ī˜ 42034
CH-8ī˜ NAME Channel-8ī˜ Name 42035ī˜ -ī˜ 42039
String
String
String
String
String
String
String
FILEī˜ NAME USBī˜ Fileī˜ Name 42040ī˜ -ī˜ 42044String
LABEL USBī˜ Label 42045ī˜ -ī˜ 42049String
CH-1 ALARMī˜ SET Channel-1 Alarmī˜ Setī˜ Value 42050
CH-1ī˜ PRE A.ī˜ SET Channel-1ī˜ Prealarmī˜ Setī˜ Value 42051
CH-1ī˜ HYSTERESIS Channel-1ī˜ Hysteresisī˜ Value 42052
CH-1ī˜ BAND ALARM Channel-1ī˜ Bandwithī˜ Value 42053
CH-2 ALARMī˜ SET Channel-2 Alarmī˜ Setī˜ Value 42054
CH-2ī˜ PRE A.ī˜ SET Channel-2ī˜ Prealarmī˜ Setī˜ Value 42055
CH-2ī˜ HYSTERESIS Channel-2ī˜ Hysteresisī˜ Value 42056
CH-2ī˜ BAND ALARM Channel-2ī˜ Bandwithī˜ Value 42057
CH-3 ALARMī˜ SET Channel-3 Alarmī˜ Setī˜ Value 42058
CH-3ī˜ PRE A.ī˜ SET Channel-3ī˜ Prealarmī˜ Setī˜ Value 42059
CH-3ī˜ HYSTERESIS Channel-3ī˜ Hysteresisī˜ Value 42060
CH-3ī˜ BAND ALARM Channel-3ī˜ Bandwithī˜ Value 42061
CH-4 ALARMī˜ SET Channel-4 Alarmī˜ Setī˜ Value 42062
CH-4ī˜ PRE A.ī˜ SET Channel-4ī˜ Prealarmī˜ Setī˜ Value 42063
CH-4ī˜ HYSTERESIS Channel-4ī˜ Hysteresisī˜ Value 42064
CH-4ī˜ BAND ALARM Channel-4ī˜ Bandwithī˜ Value 42065
CH-5 ALARMī˜ SET Channel-5 Alarmī˜ Setī˜ Value 42066
CH-5ī˜ PRE A.ī˜ SET Channel-5ī˜ Prealarmī˜ Setī˜ Value 42067
CH-5ī˜ HYSTERESIS Channel-5ī˜ Hysteresisī˜ Value 42068
CH-5ī˜ BAND ALARM Channel-5ī˜ Bandwithī˜ Value 42069
CH-6 ALARMī˜ SET Channel-6 Alarmī˜ Setī˜ Value 42070
CH-6ī˜ PRE A.ī˜ SET Channel-6ī˜ Prealarmī˜ Setī˜ Value 42071
CH-6ī˜ HYSTERESIS Channel-6ī˜ Hysteresisī˜ Value 42072
CH-6ī˜ BAND ALARM Channel-6ī˜ Bandwithī˜ Value 42073
CH-7 ALARMī˜ SET Channel-7 Alarmī˜ Setī˜ Value 42074
CH-7ī˜ PRE A.ī˜ SET Channel-7ī˜ Prealarmī˜ Setī˜ Value 42075
CH-7ī˜ HYSTERESIS Channel-7ī˜ Hysteresisī˜ Value 42076
CH-7ī˜ BAND ALARM Channel-7ī˜ Bandwithī˜ Value 42077
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
*
(ī˜ )
SET(SET -ī˜ (BAND/2)) (SET +ī˜ (BAND/2))
HYS HYS
Technicianī˜ Parameters
Technicianī˜ Pagesī˜ Parametersī˜ Definetions
USB Recording File Example
2011-06-23-17:26:09ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ 130.6ī˜ ī˜ ī˜ ī˜ 129.1ī˜ ī˜ ī˜ ī˜ 130.5ī˜ ī˜ ī˜ ī˜ 129.5ī˜ ī˜ ī˜ ī˜ 130.0ī˜ ī˜ ī˜ ī˜ 129.9ī˜ ī˜ ī˜ ī˜ 130.3ī˜ ī˜ ī˜ ī˜ 129.1ī˜ ī˜ ī˜ ī˜ SAMPLE
2011-06-23-17:26:10ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ 130.6ī˜ ī˜ ī˜ ī˜ 129.1ī˜ ī˜ ī˜ ī˜ 130.5ī˜ ī˜ ī˜ ī˜ 129.5ī˜ ī˜ ī˜ ī˜ 130.0ī˜ ī˜ ī˜ ī˜ 129.9ī˜ ī˜ ī˜ ī˜ 130.3ī˜ ī˜ ī˜ ī˜ 129.1ī˜ ī˜ ī˜ ī˜ SAMPLE
2011-06-23-17:26:12ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ 130.6ī˜ ī˜ ī˜ ī˜ 129.1ī˜ ī˜ ī˜ ī˜ 130.5ī˜ ī˜ ī˜ ī˜ 129.5ī˜ ī˜ ī˜ ī˜ 130.0ī˜ ī˜ ī˜ ī˜ 129.9ī˜ ī˜ ī˜ ī˜ 130.3ī˜ ī˜ ī˜ ī˜ 129.1ī˜ ī˜ ī˜ ī˜ SAMPLE
2011-06-23-17:26:13ī˜ ī˜ ī˜ ī˜ ī˜ ī˜ 130.6ī˜ ī˜ ī˜ ī˜ 129.1ī˜ ī˜ ī˜ ī˜ 130.5ī˜ ī˜ ī˜ ī˜ 129.5ī˜ ī˜ ī˜ ī˜ 130.0ī˜ ī˜ ī˜ ī˜ 129.9ī˜ ī˜ ī˜ ī˜ 130.3ī˜ ī˜ ī˜ ī˜ 129.1ī˜ ī˜ ī˜ ī˜ SAMPLE
Recording Time CH-1
Value
CH
Value
-2 CH
Value
-3 CH
Value
-4 CH
Value
-5 CH
Value
-6 CH
Value
-7 CH
Value
-8 Label
Calib. Low
Calibration Low value for selected channel can be adjusted according to this
parameter.
Calib. High
Calibration High value for selected channel can be adjusted according to this
parameter.
Sensor Type
Analogue input signal to be applied according to this parameter for selected channel
which is shown on Display.
0 = 4-20 mA 1 = 0-20 mA 2 = 0-10 V
A
A
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
OC/Ph/Bar
Internal Recording
The device can record in memory. When a USB memory is inserted, the recordings are
transferred to the USB memory with the file name containing the current date and
time.(Exp: 2017-07-30-09-08-12-CHAN8.txt) icon and transaction status (%)
are displayed on the screen until the transfer is complete.
If you want to eject the USB memory during transfer or recording; Press the F4 button
for 5 seconds and the USB memory must be removed (within 5 seconds) before the
icon on the screen disappears. If the USB stick is not removed during this time, the
transfer will resume from where it left off.
The device can store up to (Record time x 2) daily memos in its memory.Not:


Product specificaties

Merk: Emko
Categorie: Temperatuurregelaar
Model: CHANNEL8A-N

Heb je hulp nodig?

Als je hulp nodig hebt met Emko CHANNEL8A-N stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Temperatuurregelaar Emko

Emko

Emko ESM-1520-N Handleiding

26 Februari 2024
Emko

Emko ECO PID+ Handleiding

26 Februari 2024
Emko

Emko Eco PID Handleiding

26 Februari 2024
Emko

Emko Eco Lite Handleiding

26 Februari 2024
Emko

Emko CHANNEL8A-N Handleiding

27 November 2023
Emko

Emko ESM-7720 Handleiding

27 November 2023
Emko

Emko ESM-3711-CN Handleiding

27 November 2023
Emko

Emko ESM-4410 Handleiding

27 November 2023
Emko

Emko ESM-4435 Handleiding

27 November 2023

Handleiding Temperatuurregelaar

Nieuwste handleidingen voor Temperatuurregelaar