Emerson CKSW0555 Handleiding

Emerson Niet gecategoriseerd CKSW0555

Lees hieronder de 📖 handleiding in het Nederlandse voor Emerson CKSW0555 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 266 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Dual Clock Alarm, PLL FM Radio,
4-Level Dimmer, Wireless Charger
and Temperature Sensor
CKSW0555
Customer Service Hotline, toll free, at .1-800-898-9020
1
2
3
4
5
8
7
6
910 11 12 13 14 15 16 17
19
202122
4.) Wireless Ch arging Indicator
7.)
8
12.) Ambient Te mp er at ur e button
20.) Temperature Sens or (ba ck)
1.) Read these instructions.
2.) Keep these instructions.
3.) Heed all warnings.
4.) Follow all instructions.
5.) Do not use this apparatus near water.
6.) Clean only with dry cloth.
7.) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8.) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9.) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding type plug has two blades and a third grounding
prong. The wide blade or the third prong is provided for your safety. If the provided plug does not
fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.) Protect the power cord from being walked on or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the apparatus.
11.) Only use attachments / accessories specified by the manufacturer.
12.) Unplug this apparatus during lightning storms or when unused for long periods of time.
13.) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has
been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled
or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
14.) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or
sold with the apparatus. When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
15.) The apparatus shall not be exposed to dripping or splashing and that no
objects filled with liquids, such as vases, shall be placed on apparatus.
16.) Mains plug is used as disconnect device and it should remain readily
operable during intended use. In order to disconnect the apparatus from the
mains completely, the mains plug should be disconnected from the mains
socket outlet completely.
17.) Battery shall not be exposed to excessive heat such as sunshine, fire or the like.
PR CAUTION: Danger d’explosion si les piles sont remplacées de facon incorrect. Remplacer É
les piles seulement par le méme type de pile ou l’équivalent.
Press the or button to TUNE- TUNE+
adjust the Year (’y22’=year 2022 and so on);
Setting The Date
Setting The Time
Checking The Current Year-Date-Day of Week-Time Settings
Press the button repeatedly to see the cycle of CLOCK SET
year, date, day of week and time. To restore time display mode,
leave it idle for few .seconds
the button until the Year 'Flashes',CLOCK SET the button;
5
7
8
Press the button again and release, the Date 'Flashes';CLOCK SET
Press the or button to TUNE- TUNE+ adjust
the Month;
Press the button again and CLOCK SET release,
the Date 'Flashes';
Press the button again and release, the Hour 'Flashes';CLOCK SET
Press the or button to adjust the Hour TUNE- TUNE+
(where AM indicator 'On' is AM, 'O ' is PM);ff
press and hold until the
display‘ Flashes’
Note: Time zone and clock settings can only be adjusted in Standby mode, where the
FM Radio is disabled.
Remove any descriptive labels, stickers or protective film on the front or top of the
3.) AM Indicator ('On'=AM,'Off'=PM)
10.) / button VOL- AL.1
9.) button ON/OFF
1 .) button 6TUNE-
11 Press the button again, or leave it idle for few CLOCK SET
seconds, to s all new settings and restore it to time display mode.ave
9
10
Press the button again and release, the CLOCK SET
Minutes 'Flashes';
Press the or button to adjust the MinutesTUNE- TUNE+
Press the or button to adjust the Date;TUNE- TUNE+
6
1 .) Speaker9 (back)
1 .) / button1VOL+ AL.2
1 .) utton 4CLOCK SET b
22.) FM Wire Antenna (back)
5.) Battery Compartment (bottom)
1 .) button7TUNE+
2 .) AC dapter ( ) 1 A bottom
tens of
Turn Daylight Saving Function OFF/ON (in Standby Mode Only)
Daylight Saving Time is NOT observed in Hawaii, American Samoa,
Guam, Puerto Rico, the Virgin Islands and in, most of Arizona, with
exception of the Navajo Indian Reservation in Arizona. If you do not
want the clock to adjust itself automatically according to Daylight
Saving Time, you can disable it by pressing and holding the TUNE+
(DST start date) or TUNE- (DST end date) button for 5 secs, the
display will show DST start or end date accordingly, which ‘dSt On’
means the auto Daylight Saving Time has been enabled (`On' by default).
Press the or TUNE+ TUNE- button to toggle between 'OFF' accordingly
and both start and end dates 'On' DST . Leave it idle for a few seconds to
store your new sDST setting and resume to clock mode.
IMPORTANT NOTES
Daylight Saving Time And Leap Year Adjustments
Leap Year
At “12: 00 M id ni gh t” o n Febr ua ry 2 8t h, the c al en da r displa y wi ll c ha nge to “2 .2 9” .
6.)
With Auto-Time Setting System,
13.) SNOOZ E/DI MMER /SLEE P button
15.) TIME ZO NE/MEM./ STO. button
Releas e the butto n an d the n press eith er the or butto n TIME ZON E TU NE- TU NE+
until yo ur ow n time zone appe ar s on th e di spl ay, then rele as e the b utton . The c lock
displa y wil l chang e to the co rr ect time in th e time zo ne you selected. The cl ock w il l
always return to the c or rec t time in the zo ne you sele cte d after every power
interrupt io n. If you m ove to a differ en t time zon e, simp ly chan ge t he de fa ult z on e
®
displa y to th e ne w zon e an d the S ma rtSet will rememb er that set tin g fo r you .
Visit our website at www.emersonradio.com
CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the same
or equivalent type.
cabine t, if any. Do Not remove any la be ls or sticke rs from the ba ck o r bot tom
of the cab ine t.
Unwind the li ne c ord c on necti ng th e AC adapter. Ex te nd th e wi re an te nna ful ly
and orie nt it for b ett er FM recep tion.
Front Panel
Top Panel
Setting T he Year
18
18.) Wi re less C ha rgin g Pa d
CKSW0555-20230104-00 Printed in China
CLOCK SET
Follow the instructions on sections Setting the Year/Date/Time to set the clock to
the correct year,date and time
Press the button repeatedly to check the year,date and time.CLOCK SET
Make final adjustment if necessary.
1-7
1-5
6-7
(1 or 2 )
1 2
NOTE: volume level is fixed and cannot be Wake-to-buzzer alarm adjusted.
CKSW0555
• ( ) button again Press the AL.1 AL.2 to confirm, then the Alarm Week Mode blinks. Press the
AL.1 AL.2( ) button repeatedly to select your desired Alarm Week Mode: , or .1-7 1-5 6-7
• ( ) button again to store the alarm setting and resume to clock mode. Press the AL.1 AL.2
2) Press and hold the ( ) button until the display blinks and changes from the AL.1 AL.2
current time to the Alarm1 or Alarm2 wake up time.
3) Release the ( ) button, press theAL 1.AL 2. button to adjust Hour. or TUNE- TUNE+
P . . button . P the ress the AL 1 AL(2) to confirm, then the Minutes will blink ress
TUNE- TUNE or + to adjust Minutes. button
5 to confirm then ) Press the ( ) button AL.1 AL.2 , press the or button to VOL- VOL+
adjust the alarm volume level (V01~V16) that will come on at wake up time.
4) Press the to confirm then or button to AL.1 AL.2( ) button , press the TUNE- TUNE+
select Alarm Week Mode (1-7 everyday, 1-5 weekdays or 6-7 weekends only), if
necessary.
Press the ( ) button repeatedly to turn theAL.1 AL.2 Indicator On.
1 ( ) 2
press the
Saturday 2022
6) Press the confirm and AL.1 AL.2( ) button to save the alarm settings.
IMPORTANT: Alarm settings can only be adjusted in Standby mode.
Adjusting The Wake Up Time, Alarm Week Mode And Alarm Volume
• Press and hold the ( ) button until the display blinks and changes from the currentAL.1 AL.2
time to the Alarm1(Alarm2) wake up time.
• ( ) button, or Release the AL.1 AL.2 press the TUNE- TUNE+ button to adjust Hours. Press
the button again to confirm, then the Minutes blinks. Press theAL.1 AL.2( ) or TUNE-
TUNE+ button to adjust Minutes.
6
959 Route 46 East
1.) Follow the instructions on previous page to install a new lithium battery inCR2032
the battery compartment.
2.) Connect the radio to your AC outlet and let the clock set itself.
1
2
Celsius
Fahrenheit
WARNING: DO NOT place the Temperature Sensor in the mouth or any part
of the body to avoid it from fracturing into small particles and harming you.
Sensing Room Temperature
1.) Press the button to turn the radio On. The frequency of the tuning ON/OFF
frequency will show for a few seconds on the display.
Listening To The Radio
2.) Set the vol ume level by pressing the or button to a level that isVOL+ VOL-
neither too high nor too inaudible.
3.) Select your desired radio station/frequency with the TUNING control:
a) Press or button briefly, the receiving frequency will TUNE+ TUNE-
increment or decrement by one step.
b) Press and hold the or button for two seconds then release.TUNE+ TUNE-
Auto Station Searching will be engaged, the receiving frequency will
increment or decrement automatically until a station with acceptable
reception is found.
4.) Adjust the volume control to the desired setting.
5.) When you finished listening, press the button to turn the radio Off.ON/OFF
NOTE: The FM antenna is a long wire located at the back. Extend this wire
antenna fully and orient it for better FM reception.
Storing And Recalling Radio Station Memory
When you have a few favorite radio stations to listen to, you may like to save them ,
and pick one out of them in a few seconds without needing to search it each time.
Our digital tuning technology PLL (Phase-Lock-Loop) allows you to do this easily
by following steps:
Storing Stations Into Memory
1) Make sure the radio is turned ON.
2) Tune in the desir ed station with the TUNING control described above.
3) Press and hold the button until ‘PXX’ blinks, where ‘XX’ (01~20) is the STO.
5) After deciding the memory location, press the button again, the currentSTO.
listening station is then stored accordingly.
6) The display will show the frequency of the station just stored for few seconds
and then resume to clock mode.
Recalling Stations From Memory
1) Make sure the radio is ON.
2) Press the button, ‘PXX’ shows on the display. The station according toMEM.
the memory location will be tuned in.
3) While ‘PXX’ is showing on the display, press the or button canTUNE- TUNE+
change the memory location from 1 through 20, and the station stored in that
location will then be tuned in.
4) The display will show the frequency of the station for few seconds and then
resume to clock mode.
Wake To RADIO (1 or 2 )
Press the TEMP. button to sense indoor
Temperature can be converted between
Fahrenheit and Celsius by pressing
and holding the TEMP. button while in
tem perature mode.
NOTE: When the sensor exce eds the operating range (32-140 ), it will display as ‘--F’.°F
1) Press the button after the radio is turned On.SLEEP
The display will show ‘10’ (10 minutes default). After 10
minutes countdown the radio will shut off automatically.
Each time you press the button the sleep timer increases in 10 minutes SLEEP
step (10-90, OFF minutes).
NOTE: When you change the sleep timer from the 10 minutes default setting to
a different setting, the new setting becomes the default setting. Whenever you
activate the sleep tim er it will begin with your new default setting and count
down to zero from that point.
2) To cancel the sleep timer before it counts down to ‘00’ and shut the radio Off
imm ediately, press the button once.ON/OFF
4-Level DIMMER Control
Press the button while in Standby mode and select any of the four levels.DIMMER
Wireless Charging
A 5W Wireless Charging Pad is built on top of this unit for wireless power transfer
to any Qi-compatible Smartphones or Qi-enabled Receivers over a vertical
distance of NOT more than 0.2 inches (5 mm).
1) Place your Qi-compatible smartphone or receiver (only one set at a time) on top
of the Wireless Charging Pad. The center of your smartphone or receiver must
be positioned properly right at the middle of this charging pad in order to
maximize the charging efficiency.
2) While wireless charging started or detected, the indicator will be flashing
‘Red’ slowly.
3) To make sure wireless charging performs properly, check the charging icon
and/or charging message displays on your phone.
4) While your phone is fully charged, the indicator will turn solid ‘Red’.
Please also check the charging icon and/or charging message on your
phone to ensure it is fully charged, then remove it from the wireless
charging pad.
Note:
ŸThis wireless charging pad works with Qi-compatible device including
iPhone 14/13/12/11/XS/XR/X/8/8 Plus, Galaxy S22, S21, S20, S10
Plus/S10E/S10/S9 and 5W-15W all Qi-enabled phones.
ŸWireless charging may not work properly if the protective case or
accessory placed at the back of your smartphone is thicker than 0.2
inches (5 mm), remove the protective case or accessory before placing
your phone (screen facing upward) on the wireless charging pad.
ŸDo not place any foreign objects, such as coins, keys, metallic objects,
magnets, and magnetic stripe cards, between your phone and the
wireless charger, to avoid interference or overheating. While wireless
charging error occurred, the indicator will be flashing ‘Red’ rapidly
to alert user to get the erroneous receiver removed.
NOTE: Be sure that you have set the wake up time co rrectly b y observing the AM
Indicator. If the AM Indicator is ‘On’ the wake up time is “AM”. If the AM Indicator is
‘Off’, the wake up time is “PM”.
Checking The Wake Up Times (in Standby mode only)
To check the Wake Up Time set for Alarm1 (Alarm2 ), press briefly t he ( ) button.AL.1 AL.2
• ( ) button again Press the AL.1 AL.2 to confirm, then the Alarm Volume blinks (only if it is set
to wake-to-radio alarm mode). Pre ss the or button to select yourTUNE- TUNE+
desired wake-to-radio ala rm volume ( ).V01~V16
®
Your SmartSet clock radio allows you to select from three different Alarm Week Modes
for each alarm. They are :
3.) Turn the radio bottom up and use a small scre w driver to remove the screw securing
the battery holder to the cabinet.
4) While ‘PXX’ is blinking, press the or button to change it to yourTUNE- TUNE+
desired memory location from 01 to 20. For example, ‘P03’ means the
current listening station is about to be stored on the 3rd location of the memory.
7) At the selected wake up time the radio will turn On and has its radio volume
gradually reaches its preset level. It will play for one hour and then shut Off
automatically.
8) To stop the radio sooner, press the button. The radio will stop but theON/OFF
alarm remains set and will turn the radio On again at the same time on the
following day (depending on the Alarm Week Mode setting).
9) If you do not want the alarm to turn the radio On the following day, quickly press
and release the appropriate ALARM button until alarm indicator light is Off.
n d
Suite 210, 2 Floor
Parsippany, NJ 07054
3 to 5
programmable memory location.
4.) To stop the buzzer sooner, press the button. The buzzer will stop but ON/OFF
the alarm remains set and will turn the buzzer on again at the same tim e on
the following day (depending on the Alarm Week Mode setting).
5.) If you do not want the alarm to turn the radio on the following day, quickly press
and release the appropriate ALARM button until the alarm indicator light is off.
Radio And Buzzer Alarm Operation
7.) Save these instructions for future use as yo u will have to do this again.
Snooze/Repeat Alarm
tem perature.
®
Your SmartSet clock radio has separate alarms that can be set and used
independently. You may use the alarms to wake two people at different times, or
you may use one alarm for weekdays and the other for weekend wake up times. The
procedure for adjusting the wake up times is the same for both Alarm1 and Alarm2.

Product specificaties

Merk: Emerson
Categorie: Niet gecategoriseerd
Model: CKSW0555

Heb je hulp nodig?

Als je hulp nodig hebt met Emerson CKSW0555 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Emerson

Emerson

Emerson CKD9906 Handleiding

18 November 2024
Emerson

Emerson CR175W Handleiding

18 November 2024
Emerson

Emerson CKD8300 Handleiding

18 November 2024
Emerson

Emerson SmartSet CKSW5010 Handleiding

10 Juli 2024
Emerson

Emerson SmartSet CKS8888 Handleiding

10 Juli 2024
Emerson

Emerson Sensi RS01-SG Handleiding

17 Juni 2024
Emerson

Emerson CK2023 Handleiding

16 Mei 2024
Emerson

Emerson CKS1401 Handleiding

16 Mei 2024
Emerson

Emerson MWG1191SB Handleiding

16 Mei 2024
Emerson

Emerson WBS12 Handleiding

12 Maart 2024

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Vitec

Vitec MGW Diamond-HX OG Handleiding

23 November 2024
Electrolux

Electrolux STA9 Handleiding

23 November 2024
Electrolux

Electrolux UMP3 Handleiding

23 November 2024
Electrolux

Electrolux ZS70GL Handleiding

23 November 2024
Bosch

Bosch HEZ8TK36UC Handleiding

23 November 2024
Bosch

Bosch HEZ8ZZ36UC Handleiding

23 November 2024
Bosch

Bosch HDZIT301 Handleiding

23 November 2024
Bosch

Bosch HEZBS301 Handleiding

23 November 2024
LG

LG LX-330 Handleiding

23 November 2024
Stamos

Stamos S-PLASMA 60U Handleiding

23 November 2024