Elkay ECH8GRN Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Elkay ECH8GRN (2 pagina's) in de categorie Water dispenser. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
98663C (Rev. B - 6/13)
ECH8GRN*1B
INSTALLATION
1. When mounting unit in an open area, to insure proper ventilation,
maintain a 4" (102mm) clearance from cabinet louvers on each side
of cooler . When mounting unit in a cavity or behind a wall maintain
minimum space of 4" (102mm) on each side, 4" (102mm) on the top
and a depth of 12" (305mm).
2. Water inlet is 1/4" (6 mm) O.D. tube. Contractor to supply the
connections as required.
3. Connecting lines to be of unplated copper, thoroughly flushed to
remove all foreign matter before being connected to cooler. If
flushing does not remove all particles, a water strainer should be
installed in supply line. This cooler is manufactured in such a manner
that it does not in any way cause taste, odor, color or sediment
problems.
4. Connect cooler to building supply line with a shut-off valve and
install the in-line strainer between the valve and cooler.
5. Electrical: Make sure power supply is identical in voltage, cycle,
and phase to that specified on cooler serial plate. Never wire
compressor directly to the power supply.
6. This chiller has been designed for use with potable water ONLY.
START-UP
1. Open supply line valve.
2. Purge air from all water lines by operating bubbler valve of
fountain to which cooler is connected. Steady stream assures all
air is removed.
3. Rotate fan to insure proper clearance and free fan action.
4. Connect to electrical power.
TROUBLE SHOOTING & MAINTENANCE
Temperature Control: Factory set at 50°F 5°) under normal
conditions. For colder water, adjust screw on item no. 12 in
clockwise direction.
Ventilation: Cabinet louvers and condenser fins should be
periodically cleaned with brush, air hose or vacuum cleaner.
Excess dirt or poor ventilation can cause no cold water and
compressor cycling on the compressor overload protector.
Lubrication: Motors are lifetime lubricated.
Actuation of Quick Connect Water Fittings: Cooler is provided
with lead-free connectors which utilize an o-ring seal. To remove
tubing from the fittings, relieve water pressure, push in on gray
collar while pulling on the tubing. To insert tubing, push tube
straight into fitting until it reaches a positive stop, approximately
3/4”.
TUBE IS SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
NOTE: WATER FLOW
DIRECTION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
1/4" O.D. TUBE
WATER INLET
TO CHILLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
LEGEND
A = 1/4" O.D. TUBE WATER OUTLET C = TEMPERATURE ADJUSTMENT
B = 1/4" O.D. TUBE WATER INLET D = ELECTRICAL
ECH8GRN Refrigeration Package
Installation Instructions
IMPORTANT! INSTALLER PLEASE NOTE.
The grounding of electrical equipment such as telephone, computers, etc., to water lines is a common procedure. This ground-
ing may be in the building, or may occur away from the building. This grounding can cause electrical feedback into a water
chiller, creating an electrolysis which causes a metallic taste or an increase in the metal content of the water. This condition is
avoidable by using the proper materials indicated below.
NOTICE: This water cooler must be connected to the water supply using a dielectric coupling.
10 1/4"
261mm
16 3/4"
425mm
1 3/4"
95mm
REF.
C
D
13 1/4"
338mm
1"
25mm
1 3/8"
35mm
2"
50mm
B
1 1/8"
29mm
3 3/8"
86mm
A
98663C (Rev. B - 6/13)
ECH8GRN*1B
EVAPORATOR TANK ASSY
CABINET
CONDENSER
MOTOR - FAN 115V
BRACKET - FAN MOUNTING
BLADE - FAN
NUT - FAN BLADE
SHROUD - FAN
HEAT EXCHANGER
DRIER
COMPRESSOR SERVICE PAK
COLD CONTROL
PANEL - FRONT
COVER - RELAY
OVERLOAD
RELAY
RUN CAPACITOR
GROMMET
STUD - COMP. MOUNTING
CLIP
BUMPER
BASEPLATE
PANEL - REAR
IN-LINE STRAINER
ELBOW - 5/16" x 1/4"
66817C
28478C
66743C
31490C
20282C
30664C
70018C
56237C
66576C
66703C
0000000768
35839C
28477C
35768C
36238C
36271C
36272C
100806740570
101516143550
19037000
50930C
27303C
22300C
55996C
75583C
ITEM
NO. PART NO.
1
2
3
4
5
6
7
8
9
10
*11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
115V ITEMIZED PARTS LIST
DESCRIPTION
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY,
REPLACE WITH SAME COMPRESSOR USED IN ORIGINAL
ASSEMBLY.
NOTE: All correspondence pertaining to any of the above water
cooler or orders for repair parts MUST include model number and
serial number of cooler, name and part number of replacement
part.
WIRING DIAGRAM
23
24 4, 5, 6,
7, 8
22
10
9
12
11, 14, 15, 16,
21
3
2
1
13
25
17
RUN
CAPACITOR
COMPRESSOR
OVERLOAD
RELAY
6
COLD CONTROL
(WATER)
3
2
1
C
S M
5
2
1
3FAN BLK
GND
WHT
PRINTED IN U.S.A.
ELKAY MANUFACTURING COMPANY 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640


Product specificaties

Merk: Elkay
Categorie: Water dispenser
Model: ECH8GRN

Heb je hulp nodig?

Als je hulp nodig hebt met Elkay ECH8GRN stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Water dispenser Elkay

Elkay

Elkay EF1500VRBMC Handleiding

30 September 2024
Elkay

Elkay MB23A Handleiding

4 September 2024
Elkay

Elkay MB24 Handleiding

4 September 2024
Elkay

Elkay ECH8GRN Handleiding

4 September 2024
Elkay

Elkay LK4590FR Handleiding

4 September 2024
Elkay

Elkay LK4590SFR Handleiding

4 September 2024

Handleiding Water dispenser

Nieuwste handleidingen voor Water dispenser