Elektrobock Pocket Home PH-BP1-V Handleiding
Elektrobock
Vloerverwarming
Pocket Home PH-BP1-V
Lees hieronder de 📖 handleiding in het Nederlandse voor Elektrobock Pocket Home PH-BP1-V (8 pagina's) in de categorie Vloerverwarming. Deze handleiding was nuttig voor 56 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld
Pagina 1/8
• Element of the PocketHome® system
• Transmitter for the PH-BP1-P9 receiver
• Detects the room temperature and
sends requirement for circuit switching
P
DISPLAY DESCRIPTION: CONTROL ELEMENTS:
: used for selection of functions
: selection of preset temperatures
: information button (when pushed in the AUTO
mode, it gradually shows information on the
required temperature (PO:t), current hour/
temperature (CL:O/tE:P), operating hours
(SU:MA) and day (dE:n).
confi rmation button (ENTER)
for selection of functions and temperature
setting
1, indication of the preset time and temperature
program
2, indication of the selected function AUTO, MANU,
PROG, etc.
3, indication of anti-freeze temperature (3°C)
4, indication of temperatures, comfortable ,
economical , party P
5, indication of time / temperature
Fce
i
1
2
3
4
5
P
The PH-BP1-V transmitter in connection with the 9-channel receiver PH-BP1-P9 is used for wireless
control of individual rooms (zone control) in a fl oor heating system. There is no need to install any con-
necting cables between the receiver and transmitters (room thermostats)! The entire set can be included
in the PocketHome® system and all zones controlled from a single point by means of a central unit and/
or through a PC. In that case it is fi rst necessary to activate the PH-BP1-V transmitter in the central unit
(see Putting in operation in the PocketHome® system)!
In objects which do not necessitate central control the assembly can also work autonomously without a
central unit. The PH-P1-P9 receiver can be controlled by means of up to 9 PH-BP1-V transmitters.
DESCRIPTION
INSTALLATION
1) The transmitter is easily portable, yet we recommend that it be located in a suitable place where its activity will not
be affected by direct fl ow of hot air from a heater, solar radiation or other disturbing effects. Also avoid its
installation on an external wall.
2) Install the transmitter (indoors) as far as possible (at least 0.5 m) from big metal objects and from power lines to
avoid interference of signal reception!
3) We recommend that the installation be done by a person adequately qualifi ed in electrical engineering!
4) To prevent interference and affection of systems, every system is protected by its unique factory-saved code!
5) For correct communication of all elements in the PocketHome® system with the PH-CJ37 / Plus central unit, the
code must be learned = every element ACTIVATED in the central unit!!!
6) As the entire system works at two-way radio frequency of 433.92 MHz, follow the installation and location
instructions!
! Caution:
LOCATION AND EXCHANGE OF BATTERIES
- Lift off the back part by pushing the latch at the arrow
and remove the protective paper from the batteries (at
fi rst use); thus the transmitter becomes functional.
- Necessity to exchange the batteries is indicated by the
“ ” symbol fl ashing on the display (this information Ba:tt
can also be directly obtained on the central unit or in the
PC program (see the PH-CJ37/Plus manual).
- Always use alkaline batteries 2 x 1.5 V type AA
Dispose of used batteries in conformity with
regulations for dealing with hazardous waste! 2
Pushing the Fce button and then the button, you can choose the following functions:
1. AUTO : thermostat works according to the preset program.
2. MANU : used for manual setting of temperature (selection with the P button or the
buttons; the temperature remains constant until the next change.
3. CL:O : current day and time setting.
4. PROG : programming mode.
5. PA:r : setting of parameters (constants).
6. OF:F : PH-BP1-V is switched off permanently in this mode (except for the “ “ mode ).
7. UA:dr : learning the unique number from the central unit / learning the code in the PH-BP1-P9 receiver
FUNCTIONS
Note: If no button is pushed within 2 minutes, the transmitter resumes the basic mode.
After long push, the button function speeds up.
PA:r1 options for data on the display
- Push the Fce button, chose the PA:r (parameters) function with the , confi rm with i.
- PA:r1 appears on the display
- Confi rm with the i and with the choose the option for displayed data in the basic
mode:
current temperature displayt
C current time display
- Confi rm your choice by pushing the i button again.
PA:r2 economical temperature (17°C by default)
- PA:r2 appears on the display
- Confi rm with the i button and set the economical temperature with the button; confi rm
with the i button again.
1, Push the Fce button, chose the function with the button, confi rm CL:O (clock)
with the i .
2, Time appears on the display and hour indication is fl ashing; set the desired value with the
button and confi rm with the i button. Minute indication starts fl ashing; set the
desired value with the button and confi rm with the i.button again. The day value
appears (d:1 Monday to d:7 Sunday); select the current day with the button and
confi rm with the i button again.
TIME SETTING - CL:O FUNCTION current time and day
Product specificaties
| Merk: | Elektrobock |
| Categorie: | Vloerverwarming |
| Model: | Pocket Home PH-BP1-V |
Heb je hulp nodig?
Als je hulp nodig hebt met Elektrobock Pocket Home PH-BP1-V stel dan hieronder een vraag en andere gebruikers zullen je antwoorden
Handleiding Vloerverwarming Elektrobock
17 Maart 2023
Handleiding Vloerverwarming
- Vloerverwarming AEG
- Vloerverwarming Arnold Rak
- Vloerverwarming Danfoss
- Vloerverwarming DiLux
- Vloerverwarming Haceka
- Vloerverwarming Hager
- Vloerverwarming HomeMatic
- Vloerverwarming Laminotherm
- Vloerverwarming Magnum
- Vloerverwarming Radson
- Vloerverwarming THERMAFLEX
- Vloerverwarming VH
- Vloerverwarming WTH
- Vloerverwarming JowiTherm
- Vloerverwarming EasyHeat
- Vloerverwarming Chromoflex
- Vloerverwarming Veria
Nieuwste handleidingen voor Vloerverwarming
3 December 2024
3 December 2024
3 December 2024
3 December 2024
4 Juli 2023
3 Juli 2023
29 Juni 2023
26 Juni 2023
24 Juni 2023
23 Juni 2023