Electro Harmonix Tri Parallel Mixer Handleiding

Electro Harmonix Schakelaar Tri Parallel Mixer

Lees hieronder de 📖 handleiding in het Nederlandse voor Electro Harmonix Tri Parallel Mixer (11 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 42 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/11

TRI PARALLEL MIXER

Effects Loop Mixer/Switcher

Congratulations on your purchase of the Electro-Harmonix Tri Parallel

Mixer! The Tri Parallel Mixer can be used in multiple configurations for a

variety of switching and mixing applications. Use it to switch between or

mix up to three separate effects loops. Send a guitar or other

instrument out to three separate amplifiers, or input three separate

instruments to switch between or mix to a single output. Mix effects in

parallel to create sounds and allow for options not possible when using

effects in series (one after another). These are a few examples of the

multiple ways to incorporate the Tri Parallel Mixer into your setup.

- USING THE TRI PARALLEL MIXER -

Plug the 9VDC adapter into the jack on the top left of the Tri Parallel

Mixer. There are multiple ways to configure your setup, the most typical

configuration is shown below: a guitar based setup for mixing and/or

switching between three separate effects loops.

WARNING: Your Tri Parallel Mixer comes equipped with an Electro-Harmonix 9.6DC-

200BI power supply (same as used by Boss® & Ibanez®: 9.6 Volts DC 200mA). The Tri

Parallel Mixer requires at 9VDC with a center negative plug. Use of the wrong 45mA

adapter or a plug with the wrong polarity may damage your Tri Parallel Mixer and void

the warranty.

In this configuration, plug your guitar or other instrument/sound source

into the INPUT jack on the right of the Tri Parallel Mixer. Connect your

amplifier or other sound destination to the OUTPUT jack on the left of

the Tri Parallel Mixer. All connections can be made using standard ¼”

instrument cables.

Connect the input of the first effect in your first effects loop to the SEND

1 jack. Connect the output of the last effect in your first effects loop to

the RTN 1 jack. Repeat this step for your other two effects loops using

the SEND 2/3 and RTN 2/3 jacks. Below is the signal path in this

configuration:

Use the CH 1/2/3 footswitches to activate their respective effects loops.

Double tap any of these footswitches to enter master bypass, which

connects the INPUT jack directly the OUTPUT jack. When in bypass,

single tap any footswitch to re-enter active mode. There are other

switching options and configuration options that will be discussed later in

this manual.

-GLOBAL CONTROLS / JACKS-

INPUT –This jack on the right of the unit is the master input for the Tri

Parallel Mixer. The signal present here will be outputted to an active

channel’s SEND jack. In master bypass, the input signal connects

directly to the OUTPUT jack.

OUTPUT –This jack on the left of the unit is the master output for the

Tri Parallel Mixer.

MASTER VOL –This knob sets the master output level of the mixer.

DRY VOL –This knob sets how much dry signal (the signal present at

the INPUT jack) is sent to the output of the Tri Parallel Mixer.

MASTER STATUS –This LED lights when the unit is active and doesn’t

light when in master bypass. Double tap any of the three footswitches

to switch from active to bypass mode. When in bypass, single tap any

footswitch to enter active mode. The Tri Parallel Mixer features buffered

bypass.

-CHANNEL CONTROLS / JACKS-

The majority of the controls for the Tri

Parallel Mixer are grouped into three

identical channel sections, each with a

SEND and RTN (Return) jack, a SEND and

RETURN level control, an EQ control, a

PHASE switch, and a footswitch.

SEND 1/2/3 Jack This jack outputs the –

signal inputted to the Tri Parallel Mixer (via

the INPUT jack) when its channel is

active . *Send output impedance = 220Ω.

SEND Knob –This knob sets the level

outputted to the SEND jack.

RTN 1/2/3 Jack –This jack is the input

for a given channel. The signal inputted to

this jack is sent to the OUTPUT jack (after

the EQ control) when its channel is

active . * RTN input impedance = 1MΩ.

RETURN Knob –This knob sets the level of the signal received at the

RTN jack before it is sent to the output of the Tri Parallel Mixer.

PHASE –This switch, when set to 180, inverts the phase of the signal

sent out of the SEND jack. This can be useful when something in your

effects loop is causing phase issues when mixed in with either your dry

signal or other effects loops.

Product specificaties

Merk:	Electro Harmonix
Categorie:	Schakelaar
Model:	Tri Parallel Mixer

Heb je hulp nodig?

Als je hulp nodig hebt met Electro Harmonix Tri Parallel Mixer stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Schakelaar Electro Harmonix

Electro Harmonix Triple Foot Controller Handleiding

12 Juni 2023

Electro Harmonix Switchblade Pro Handleiding

18 Mei 2023

Electro Harmonix Tri Parallel Mixer Handleiding

16 Mei 2023

Handleiding Schakelaar

Nieuwste handleidingen voor Schakelaar

Smart-AVI SM-DVN-2D Handleiding

21 December 2024

Smart-AVI SM-DPN-2Q Handleiding

21 December 2024

Smart-AVI DVN-16P Handleiding

21 December 2024

Smart-AVI SM-DVN-4D Handleiding

21 December 2024

Smart-AVI SM-EDPN-4S Handleiding

21 December 2024

Smart-AVI SM-EDPN-4D Handleiding

21 December 2024

Smart-AVI SM-EDPN-2Q Handleiding

21 December 2024

Smart-AVI SM-DVN-4S Handleiding

21 December 2024

Smart-AVI SM-UHN-2D Handleiding

21 December 2024

Smart-AVI SM-UHN-2S Handleiding

21 December 2024