Ei Electronics MCP401RC Handleiding

Ei Electronics Schakelaar MCP401RC

Lees hieronder de 📖 handleiding in het Nederlandse voor Ei Electronics MCP401RC (2 pagina's) in de categorie Schakelaar. Deze handleiding was nuttig voor 49 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

MCP401RC Manual Call Point

Disconnect the AC mains power supply from the circuit that is to

be used to power the smoke/heat alarms and the MCP401RC.

Install the Smoke/Heat/CO Alarms as per the Installer

Instructions supplied with the alarms.

Select a suitable location where the MCP401RC can be easily

accessed. The unit should not be exposed to dripping or splashing.

Route the wiring (Live, Neutral, Interconnect/Control and Earth)

to the MCP401RC siting location. A minimum 0.75mm

2cable

should be used.

With the 25mm screws provided, fix the mounting box to the wall.

Secure the wall plate to the mounting box using the 35mm

machine screws provided.

SURFACE MOUNTING BOX

SECURITY SCREW

1.5 x 10mm

SCREW (2)

3.5 x 35mm

WALL PLATE

FRONT COVER

OPERATING ELEMENT

SCREW (2)

3.5 x 25mm

Figure 1

Installation & Wiring

6Figure 2

To additional Ei Alarms

if required

(compatible alarms

listed above)

Figure 3

When the black spot on the front face of the MCP401RC is pressed, an alarm signal will be sent along the

interconnect line and all interconnected alarms will sound. The MCP401RC switch element can be reset using

the plastic key supplied.

PLEASE NOTE: The MCP401RC is designed for use with the following models of Smoke/Heat/CO Alarms

- Ei161RC, 164RC, 166RC, 141, 144, 146, 151TL, 154TL, 156TLH, 261ENRC, 261DENRC.

WARNING: This Manual Call Point should be installed by a qualified electrician in accordance with the

Requirements for Electrical Installations published by the Institute of Electrical Engineers (BS7671 current edition).

A maximum of 4 MCP401RC units can be installed on one system in addition to 12 interconnect alarms.

B16073-R0-MCP401RC-UC-ENG 19/4/07 9:17 AM Page 1

P/N B16073 Rev 0

Testing

It is recommended that the MCP401RC is tested directly after installation and then at least monthly.

Test that the MCP401RC call point triggers the alarm(s) by pressing the black spot on the front cover. A

striped warning indicator should drop down into view on the front face (visible through the clear plastic

window). Check that each alarm in the system is sounding.

Reset the MCP401RC by following the instructions in the Resetting section below. The alarms should stop

sounding.

Now turn off the mains power to the system. Repeat the test above (this checks the rechargeable back-up

in the unit). Reinstate the mains power to the system. The MCP401RC will operate in standby with mains

off for over 6 months. With the Manual Call Point triggered it can give an alarm signal for over 16 hours.

The crossed out wheelie bin symbol that is on your

product indicates that this product should not be disposed

of via the normal household waste stream. Proper

disposal will prevent possible harm to the environment or

to human health. When disposing of this product please

separate it from other waste streams to ensure that it can

be recycled in an environmentally sound manner. For

more details on collection and proper disposal, please

contact your local government ofce or the retailer where

you purchased this product.

Aico Ltd. Mile End Business Park,

Maesbury Rd, Oswestry,

Shropshire, SY10 8NN, U.K.

Tel: 0870 7584000 www.aico.co.uk

Ei Electronics. Shannon, Ireland.

Tel: +353 (0)61 471277 www.eielectronics.com

Connect the wiring as shown in Figures 2 & 3 previously. Note: the Earth connection is for convenient

termination of the earth conductor and is not required for the safety of the unit. The wiring should be

installed securely (e.g. tie wrap together) to prevent a hazard if one becomes detached.

Carefully slide the front cover and circuit board diagonally into the mounting box, top section first (see Figure 4).

Then carefully locate the top of the front cover onto the top of the wall plate and hinge down to snap

securely in place (see Figure 5).

Fit the security screw to the call point - the hole for this is on the bottom face of the front cover (see

Figure 6). This is essential for electrical safety as mains is present within the unit.

Reconnect the AC mains power to the circuit and check that the green mains indicator lights on the

Smoke/Heat/CO Alarms are on.

Figure 4 Figure 5 Figure 6

To reset the unit, insert the

reset key into the hole in the

bottom of the front cover. The

striped warning indicator

should disappear. With the key

still inserted, twist it anti-

clockwise until the operating

element clicks back into place,

then remove the reset key (see

Figure 7).

Figure 7 Figure 8

To detach the front cover,

remove the security screw and

insert the reset key into the

bottom of the cover. With the

key firmly inserted, hinge the

bottom of the cover away from

the wall plate/ mounting box

(the reverse motion to fitting).

See Figure 8.

Resetting Opening Unit / Removal

B16073-R0-MCP401RC-UC-ENG 19/4/07 9:17 AM Page 2

Product specificaties

Merk:	Ei Electronics
Categorie:	Schakelaar
Model:	MCP401RC
Kleur van het product:	Red,White
Gewicht:	200 g
Breedte:	90 mm
Diepte:	47 mm
Hoogte:	90 mm
Montage gereedschap:	Ja
Connectiviteitstechnologie:	Draadloos
Type stroombron:	AC
Materiaal:	Glass,Polycarbonate
Ingangsspanning:	230 V
Frequentie:	50 Hz
Compatibele producten:	Ei161RC, 164RC, 166RC, 141, 144, 146, 151TL, 154TL, 156TLH, 261ENRC, 261DENRC.
Koppelbaar:	Ja
Bedrijfstemperatuur (T-T):	0 - 40 °C
Relatieve vochtigheid in bedrijf (V-V):	0 - 90 procent
Batterijtechnologie:	Lithium
Back-upbatterij:	Ja
Aantal onderling verbonden alarmen (max):	12