Edge Boost Micro Handleiding

Edge Solid state drives (ssd) Boost Micro

Lees hieronder de 📖 handleiding in het Nederlandse voor Edge Boost Micro (1 pagina's) in de categorie Solid state drives (ssd). Deze handleiding was nuttig voor 63 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/1

INSTALLATION (continued)

SYSTEM REQUIREMENTS

Version 1013-1.6

INTRODUCTION

● A computer with a Micro SATA interface connector

● An available Micro SATA power connector

● Ensure all power sources, including the wall power adapter and battery,

are disconnected from your system before installing

● Do not expose the SSD to extreme temperatures or sunlight

● Do not touch the gold SATA connectors of the SSD

● Be conscious of static electricity—wear a wrist strap while installing the

SSD to minimize this

The EDGE Boost SSD comes with a powerful AES hardware encryption chip. When

enabled, the SSD becomes impossible to access without knowing the password.

Even if the SSD is physically removed from your system, all stored data is invisible

and secure. Not all systems support drive encryption (also called the ATA Security

Password)—please consult your system’s user manual to ensure this feature is

available.

You must first enable the drive encryption to use it. Enabling this function varies

from system to system, but the following is a typical example (IMPORTANT: Your

SSD will be permanently inaccessible if you forget or lose your password!):

1. After installing the SSD, access your computer’s BIOS during system startup.

2. Select the “Security” option.

3. Select the “Password” option.

4. Select the option displayed as “Hard Disk Password” or similar for the Boost SSD.

5. Create and reconfirm a password. After complete, the encryption function is

active. You will need to input your password every time you start your computer to

access the SSD.

1. Ensure all power sources, including the wall power adapter and

battery, are disconnected from your system.

2. Disassemble your computer’s casing and locate the hard drive.

3. Remove the old hard drive and replace with the Boost SSD. If the old

hard drive has any hardware attached to it, remove it and attach to

the Boost SSD in the same manner.

4. After the install is complete, reassemble the computer to its original

state and restore power.

5. Power on the system and ensure that the system’s BIOS recognizes

the Boost SSD. Note: You will need to format the SSD before use if

you plan to use it as a secondary storage drive.

PRECAUTIONS

USING THE ENCRYPTION FUNCTION

WARRANTY

This SSD is backed by a 5-year warranty. When properly installed, EDGE

Memory warrants that this product will be free from substantial defects in

material and workmanship for the aforementioned warranty period. For

complete warranty details, please visit www.EDGEMemory.com.

1.8" SOLID STATE DRIVE

EDGE BOOST MICRO SSD

Help getting started with your EDGE Boost Micro Solid State Drive

Quick Start Guide

INSTALLATION

Your installation experience will vary depending on the type of notebook

or other system you install the Boost SSD into—refer to your system’s

user manual while installing. The following are some general directions

that may help while installing:

FORMATTING

The Boost SSD comes unformatted—you must format the device before

using. The following instructions are designed for Windows 7. Other

versions of Windows will be similar, but may vary. If using a Mac, please

access Utilities -> Disk Utility -> Partition to initiate a format.

1. Right click on Computer My Computer (or ) and select .Manage

2. Select Disk Management in the left pane.

3. You will receive an Initialize Disk prompt—this will only apply to any

unformatted devices you have installed (i.e. – the SSD). Choose MBR,

note the Disk number (ex Disk 1, Disk 2, etc), and select OK.

4. In the bottom pane of Disk Management, find the disk number from step

3. Right-click on the unallocated New Simple Volumebox and select .

5. The New Simple Volume/Partition wizard will appear. Select on Next

the first screen.

6. On the Specify Volume Size screen, ensure the Simple Volume size

number matches the maximum disk space (default). Select Next.

7. Assign a drive letter not already in use to the SSD. Select .Next

8. Choose a file system format ( recommended for Windows) with a NTFS

default allocation unit size Volume Label and give the SSD a name.

Check perform a quick format enable file and folder and uncheck

compression. Click .Next

9. Review the wizard summary and select Finish. The SSD will be

formatted. Once complete, you can close Computer Management.

FORMATTING (continued)

www.EDGEMemory.com/support

CUSTOMER SUPPORT

Need Help?

Thank you for purchasing an EDGE Boost SSD! This guide is designed to give

you basic information on installing and using the SSD, as well as some

precautions to adhere to.

It is important to be familiar with the environment in which you plan to install

the SSD in before getting started. Disassembling and reassembling covers,

lids, bezels, and other items may be required for installation. Please consult

your system’s user manual or contact an IT professional for assistance if you

are unsure about the install process.

Please note that additional accessories such as brackets or trays may be

required to properly install your SSD.

™

Product specificaties

Merk:	Edge
Categorie:	Solid state drives (ssd)
Model:	Boost Micro
Kleur van het product:	Grijs
Gewicht:	45 g
Breedte:	53.6 mm
Diepte:	78 mm
Hoogte:	4.8 mm
Connectiviteitstechnologie:	Bedraad
Interface:	micro SATA
Ondersteunde beveiligingsalgoritmen:	128-bit AES
Ondersteunt Windows:	Ja
Temperatuur bij opslag:	-55 - 95 °C
Intern:	Ja
Ondersteunt Mac-besturingssysteem:	Ja
SSD capaciteit:	80 GB
Ondersteunt Linux:	Ja
ECC:	Ja
SSD-vormfactor:	1.8"
Mean time between failures (MTBF):	2000000 uur
Slaapstand:	0.5 W
Type geheugen:	MLC
Leessnelheid:	280 MB/s
Schrijfsnelheid:	275 MB/s
Overdrachtssnelheid:	3 Gbit/s
Schokbestendigheid:	1500 G
Bedrijfstemperatuur (T-T):	0 - 70 °C
S.M.A.R.T. support:	Ja
Random write (4KB):	50000 IOPS
TRIM support:	Ja
Stroomverbruik (lezen):	2.5 W
Stroomverbruik (schrijven):	2.5 W