ECS G41T-R3 (V1.0A) Handleiding

ECS Moederbord G41T-R3 (V1.0A)

Lees hieronder de 📖 handleiding in het Nederlandse voor ECS G41T-R3 (V1.0A) (64 pagina's) in de categorie Moederbord. Deze handleiding was nuttig voor 80 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/64
Preface
Preface
Copyright
This publication, including all photographs, illustrations and software, is protected
under international copyright laws, with all rights reserved. Neither this manual, nor
any of the material contained herein, may be reproduced without written consent of
the author.
Version 1.0
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any
particular purpose. The manufacturer reserves the right to revise this publication and
to make changes from time to time in the content hereof without obligation of the
manufacturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective
owners and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa-
tion. This equipment generates, uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment onto an outlet on a circuit different from that to
which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits govern-
ing this device. Changes or modifications not expressly approved by the system ’ s
manufacturer could void the user’s authority to operate the equipment.
ii
Preface
Declaration of Conformity
This device complies with part 15 of the FCC rules. Operation is subject to the
following conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received, including interfer-
ence that may cause undesired operation
Canadian Department of Communications
This class B digital apparatus meets all requirements of the Canadian Interference-
causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du Réglement sur
le matériel brouilieur du Canada.
About the Manual
The manual consists of the following:
Chapter 1
Introducing the Motherboard
Chapter 2
Installing the Motherboard
Chapter 3
Using BIOS
Chapter 4
Using the Motherboard Software
Describes features of the
motherboard.
Go to Hpage 1
Describes installation of motherboard
components.
Go to Hpage 7
Provides information on using the
BIOS Setup Utility.
Go to Hpage 25
Describes the motherboard software.
Go to Hpage 43
Chatper 5
Setting Up eJIFFY
Describes the eJIFFY setting up
Go to Hpage 47
Chatper 6
Trouble Shooting
Provides basic trouble shooting tips
page 57Go to H
iii
TT
TT
TABLE OF CONTENTSABLE OF CONTENTS
ABLE OF CONTENTSABLE OF CONTENTS
ABLE OF CONTENTS
Preface i
Chapter 1 1
Introducing the Motherboard 1
Introduction......................................................................................1
Feature...............................................................................................2
Specification......................................................................................5
Motherboard Components.............................................................6
Chapter 2 7 7 7 7 7
Installing the Motherboard 7
Safety Precautions............................................................................7
Choosing a Computer Case.............................................................7
Installing the Motherboard in a Case............................................7
Checking Jumper Settings...............................................................8
Setting Jumpers...................................................................8
Checking Jumper Settings...................................................9
Jumper Settings...................................................................9
Installing Hardware........................................................................10
Installing the Processor.....................................................10
Installing Memory Modules...............................................12
Expansion Slots.................................................................15
Connecting Optional Devices............................................17
Installing a Hard Disk Drive/CD-ROM/SATA Hard Drive..19
Connecting I/O Devices................................................................21
Connecting Case Components.....................................................22
Front Panel Header...........................................................24
Chapter 3 2525
2525
25
Using BIOS 25
About the Setup Utility................................................................ 25
The Standard Configuration..............................................25
Entering the Setup Utility....................................................25
Resetting the Default CMOS Values...................................26


Product specificaties

Merk: ECS
Categorie: Moederbord
Model: G41T-R3 (V1.0A)
Breedte: 225 mm
Diepte: 170 mm
Grafische adapter: GMA X4500
Type stroombron: ATX
Aantal USB 2.0-poorten: 4
VGA (D-Sub)poort(en): 1
Microfoon, line-in ingang: Ja
Aantal Ethernet LAN (RJ-45)-poorten: 1
Hoofdtelefoonuitgangen: 1
Processor socket: LGA 775 (Socket T)
Maximum intern geheugen: 8 GB
Ingebouwde grafische adapter: Ja
Audio-uitgangskanalen: 5.1 kanalen
Netwerkfuncties: Fast Ethernet
Meegeleverde drivers: Ja
PCI Express x1 slots: 1
PCI Express x16 slots: 1
PS/2 poort(en): 2
PCI-slots: 1
Compatibele processors: Intel Core 2 Duo, Intel Core 2 Quad
Moederbord form factor: micro ATX
Aantal geheugenslots: 2
Supported memory clock speeds: 800,1066,1333 MHz
BIOS type: AMI
Grootte BIOS-geheugen: 64 Mbit
Ondersteuning voor parallel processing: Niet ondersteund
Aansluitingen voor behuizingsventilatoren: 1
ATX Power connector (24-pin): Ja
Aantal SATA-aansluitingen: 2
USB 2.0 aansluitingen: 2
Aansluiting voor audiopaneel aan voorzijde: Ja
Chassis intrusion aansluiting: Ja
S/PDIF uitgang: Ja
Aantal Parallel ATA aansluitingen: 1
Aansluitingen voor EATX voedingen: 1

Heb je hulp nodig?

Als je hulp nodig hebt met ECS G41T-R3 (V1.0A) stel dan hieronder een vraag en andere gebruikers zullen je antwoorden