Ebm-papst 3314 NN Handleiding

Ebm-papst Ventilator 3314 NN

Lees hieronder de 📖 handleiding in het Nederlandse voor Ebm-papst 3314 NN (6 pagina's) in de categorie Ventilator. Deze handleiding was nuttig voor 10 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

page of 1 6

Operating manual

3314 NN

Product type, manufacturing date (calendar week/year of construction)

and if required, conformity mark can be found on the nameplate on the

product.

Please provide us with the contents of the nameplate when making

enquiries about the product.

ebm-papst St.Georgen GmbH & Co. KG

Hermann-Papst-Straße 1

D - 78112 St.Georgen

Phone: +49 (0) 7724 / 81-0

Fax: +49 (0) 7724 / 81- 1309

info2@de.ebmpapst.com

www.ebmpapst.com

As per: 01.03.2023

Version: 1 5

Article number: 9293510105

Original operating manual

INDEX

1 SAFETY REGULATIONS AND INFORMATION 1

2 INTENDED USE 3

3 TECHNICAL DATA 3

4 CONNECTION AND COMMISSIONING 4

5 FAULTS, POSSIBLE CAUSES AND REMEDIES 5

6 COMPLIANCE 5

1 SAFETY REGULATIONS AND INFORMATION

Read the operating manual carefully before commencing work at the

product. Pay attention to the following warnings to avoid risk to

persons or malfunctioning.

This operating manual is an integral part of the product.

In the event of resale or change of ownership the operating manual

must accompany the product. This operating manual may be copied

and provided as information on potential risks and their avoidance.

Hazard classication of warning notices

The following risk ratings are used in this operating manual to denote

potential risk situations and important safety instructions:

DANGER

This is a potentially dangerous situation

and warns of an impending health risk

or risk of fatal injury if this warning is

not observed. Observe this warning.

WARNING

The dangerous situation can occur and

can result in major or fatal injuries if the

warning is not observed. Work with

extreme care.

CAUTION

The dangerous situation can occur and

can result in minor injuries or damage

to property if the warning is not

observed.

NOTE

A potentially dangerous situation can

occur and results in damage to

property if not avoided.

Qualication of personnel

Only skilled electricians are permitted to install the product, to carry out

the test run and to work at the electrical unit.

Only instructed and authorized skilled personnel are permitted to

transport, unpack, operate and service the product.

Basic safety regulations

Safety risks related to the product must be reassessed after installing

in the nal device.

The operating manual was developed in accordance with European

market requirements and may need adapting to the market

requirements of the country in question.

When working at the product, observe the following:

 Do not make any changes to the product.

WARNING

Impermissible high load

 Stop the product immediately after

impermissible loading (e.g. impact,

heat, overvoltage).

page of 2 6

Electrical voltage and current

DANGER

Electrical voltage

Regularly check the electrical

equipment of the product.

 Eliminate immediately loose

connections and defective cables.

Safety and protective functions

DANGER

Missing safety device and faulty

protective equipment.

Without protective equipment severe

injuries can occur, e.g. by taking hold of

the rotating equipment.

 Operate the product with protection

guards only.

Electromagnetic radiation

Electromagnetic compatibility (EMC) may aect the system integration

of the product due to interaction.

 Ensure the electromagnetic compatibility of the entire system.

Moving parts

DANGER

Self-starting product

If voltage is applied, the motor

automatically restarts after a mains

failure or when blocking has been

eliminated.

 Do not stand in the danger zone of

the product.

 Switch o the mains voltage when

working on the product and secure

against switching on again.

DANGER

Rotating impeller

Contact with the impeller may result in

injuries. Long hair, loose-tting

garments and jewellery can be caught

and pulled into the product. Risk of

injury.

 Before starting the product, ensure

that it is securely xed and that the

guards are in place.

 Do not wear loose-tting garments

or jewellery when working on

moving parts.

 Protect long hair by wearing a hair

net.

CAUTION

High risk of re spreading

Can cause re to spread.

 Never direct the airow

(intake/exhaust side) at a potential

source of re.

Hot surface

CAUTION

High temperature at motor housing.

Risk of burns

 Provide adequate protection against

accidental contact.

Transport

Only transport the product in its original packaging. Secure during

transpor t.

The vibration values, temperature and climate ranges should not

be exceeded during transport.

Storage

 Store the device, partially or fully assembled, in a dry place,

protected against the weather and free from vibration, in the

original packaging in a clean environment.

 Protect the device against environmental eects and dirt until nal

installation.

 To guarantee trouble-free operation and the longest possible

service life do not store the device for more than one year.

 Even devices explicitly intended for outdoor use are to be stored as

described prior to commissioning.

 Maintain the storage temperature, see Chapter 3, Technical Data

Cleaning

NOTE

Product damaged during cleaning

 Clean the product carefully with a

moist cloth without applying

pressure to the rotor. Do not use

cleaning agents that contain acids,

caustic solutions or solvents.

Disposal

When disposing of the product, observe all requirements and

regulations that are relevant in your country.

page of 3 6

2 INTENDED USE

The product is designed exclusively as a built-in device for conveying

air according to the technical data.

Every use that is not in accordance with the intended purpose, is

regarded as misuse of the product.

On-site installations must comply with the mechanical, thermal and

service life requirements, see Chapter 3, Technical Data.

Intended use includes:

- Operating the product with all protective equipment

- Do not put the product into operation before it has been installed in

the customer's application

- Observation of the operating manual

Use for other than the intended purpose

Using the product for the purposes mentioned below is prohibited and

can be dangerous:

- Conveyance of air that contains abrasive particles.

- Conveyance of air that has a highly corrosive eect.

- Conveyance of air that has a high dust load, e.g. vacuuming

sawdust.

- Conveyance of inammable gases/particles.

- Contact with materials that can damage the product, e.g. acids,

caustic solutions, solvents.

- Exposure to radiation that can damage product components, e.g.

strong UV rays or thermal radiation.

- Operating during external vibration.

- Operating the product close to inammable materials or

components.

- Operating the product in an explosive atmosphere

- Use of the prouct as a safety component or for performing safety-

relevant functions.

- Operating in medical devices with life-sustaining or life-saving

function if not validated together with ebm-papst.

- Operating in non-stationary systems, e.g. railway vehicles, aircraft

and spacecraft if not validated together with ebm-papst.

- Operating with fully or partially dismantled or manipulated protective

equipment.

- Operating the product under conditions other than those mentioned

in the technical data.

- Furthermore, all fields of application not mentioned under intended

use.

An in situ assessment must be conducted of the heating behavior

(appropriate and inappropriate operation), the protection against

contact, electrical shocks, impact of foreign objects or water and the

usage at altitudes higher than 2000 meters.

Contact ebm-papst if you have specic queries regarding the product.

3 TECHNICAL DATA

Drawing, see annex

Technical description

Airow direction

Air outlet over struts

Rotating direction looking

at rotor

Clockwise

Nominal voltage

24 V

Current consumption

65 mA

Power consumption

1,6 W

Speed

2.650 1/min

Max. free-air ow

80,0 m3/h

Mass

0,19 kg

Protection class

III

Max. torque when

mounted across both

mounting anges

Wire outlet corner 80 Ncm :

Remaining corners: 80 Ncm

Screw size

ISO 4762 - degreased, M4

without an additional brace and

without washer

The product is intended for use in sheltered rooms with controlled

temperature and controlled humidity. Directly exposure to water must

be avoided.

Pollution degree 1 (according DIN EN 60664- 1)

There is either no pollution or it occurs only dry, non-conductive

pollution. The pollution has no negative impact.

Ambient conditions

Permitted ambient temperature

Transport and storage

Operation

-40 °C ... 80 °C

-20 °C ... 75 °C

Vibration and shock load

The mechanical Vibration and Shock data for the product is available.

If the operation of the product should take place in a sinusoidal

vibration containing environment or xing the product on sinusoidal

vibrating surface, please contact our technical support.

Do not operate your product in the resonance range.

Product specificaties

Merk:	Ebm-papst
Categorie:	Ventilator
Model:	3314 NN
Kleur van het product:	Zwart
Gewicht:	190 g
Breedte:	92 mm
Diepte:	32 mm
Hoogte:	92 mm
Soort:	Ventilator
Geluidsniveau (hoge snelheid:	35 dB
Materiaal:	Kunststof
Luchtstroom:	80 m³/uur
Spanning:	24 V
Rotatiesnelheid ( max):	2650 RPM
Mean time between failures (MTBF):	65000 uur
Geschikte locatie:	Computer behuizing
Stroomverbruik (typisch):	1.8 W
Bedrijfstemperatuur (T-T):	-20 - 75 °C
Ventilator diameter:	92 mm
Type lager:	Kogellager