Earlex SS77 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Earlex SS77 (4 pagina's) in de categorie Behangafstomers. Deze handleiding was nuttig voor 43 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/4
Steam Wallpaper Stripper
MODELS:
SS125
SS75
SS76
SS77
OPERATING INSTRUCTIONS
PLEASE READ THESE INSTRUCTIONS CAREFULLY BEFORE USE
Thank you for purchasing a Steam Wallpaper Stripper. This is a highly versatile machine for
use all around the home. In order to obtain the best results please read the instructions
before commencing any work.
THE MANUFACTURER WILL ACCEPT NO RESPONSIBILITY FOR THE USE OF THIS PRODUCT IF USED FOR ANY
OTHER PURPOSES THAN THOSE DETAILED HEREIN.
Please also make a special note of the safety rules and
RETAIN FOR FUTURE REFERENCE
IF YOU HAVE ANY PROBLEMS WITH YOUR STEAM WALLPAPER STRIPPER OR IF YOU BELIEVE A PART IS
MISSING, DO NOT RETURN TO STORE. PLEASE CONTACT EARLEX LTD ON 01483 454666.
B40 02-08.qxd 25/7/08 10:33 am Page 1
SYMBOLS CAUTION STEAM IS HOT!
Warning: hot liquid or steam can burn. Danger of scalding. Steam may
also condense into boiling droplets. Steam should not be directed
towards electrical appliances. Danger of scalding appears on the cap
as this symbol.
OPERATION
The unit is designed for safe, fast removal of wallpaper but please be aware
that steam is produced at 100oC - so be careful, wear protective clothing and protect your
hands with heat resistant gloves or mitts.
FILLING SS75: Remove elbow filler cap and fill unit to MAX. level indicator with clean -
preferably hot - water. Ensure that the ‘O’ ring is seated correctly on the elbow filler cap and
place elbow filler cap lugs into filler hole with the tongue pointing to the TWO O’CLOCK position.
Turn the elbow filler cap clockwise to the SIX O’CLOCK position so that the tongue locks into
place between the two teeth.
FILLING OTHER STEAM WALLPAPER UNITS: Remove filler cap and fill unit to Max.level line
or indicator with clean - preferably hot - water. Replace filler cap.
CAUTION !
Check the state of your plaster before starting work.
Steam can loosen weak, porous or poorly bonded plaster - which also loosens readily if cracked, holed or if the steam
plate is held in one position for too long after the paper is soaked. Weak plaster can normally be detected by tapping a few areas of wall. A hollow sound indicates that you should
proceed only with extreme care - stopping immediately if you hear a cracking sound or plaster starts to break loose.
The steam stripper is safe for drywall/plaster board surfaces but whatever the material, it is always wise to check a
small area before starting work properly. PROTECT YOUR HOME
The heat generated by the boiler unit can mark carpets, soft furnishings, table tops, cabinets etc. To prevent this we
recommend placing the unit on a wooden board, tray or other barrier - making sure it will not slip off one side or tilt
during use. Dust sheets or newspapers are not suitable heat protectors for delicate surfaces.
PREPARATION
To achieve fastest paper removal always gently score the areas to be stripped.
With heavily embossed, vinyl coated or painted papers this is essential. Either use a proprietory
perforator tool or alternatively score the paper with the edge of a wall scraper in a criss-cross pattern
with 150mm (6 inch) spacing. As with all decorating work be sure to protect carpets and furniture with covers.
SAFETY RULES
2
For a shorter steaming time use less water. Do not overfill the
unit or hot water will be forced up the steam hose.
Screw hose onto threaded outlets of boiler and steam plate, hand
tight is sufficient. but do check for hand tightDo not over tighten
fit from time to time during use.
Connect mains lead from unit to power socket and switch on. lt can
take up to 15 mins (approx.) before steam is produced - depending
on fill water quantity and temperature.
Do not leave unattended and keep children & pets out of the room.
SWS MODEL BOILER CAPACITY STEAM TIME
SS75 5L 90 Mins*
SS76 5L 90 Mins*
SS77 5L 78 Mins*
SS125 4L 72 Mins*
* Approx steam time before the safety cut-out operates.
lKeep equipment away from children and pets.
lEnsure boiler is placed on a flat level surface, and
should the boiler become tilted in use - level again
immediately.
Failure to do so can result in severe overheating,
complete element failure and void of your
guarantee.
lBlock boiler unit securely if using on stairs.
lThe boiler becomes hot in use. Move only by using
the carrying handle.
lSteam is produced at 100oC. Be careful, wear
protective clothing and protect your hands with
heat resistant gloves or mitts.
lNever point hose or steam plate at anyone.
lAlways keep steam plate tilted away from face and
body, beware of hot drips and regularly empty
collected condensation from plate - especially when stripping
ceilings and high areas.
lNever remove filler cap or detach hose whilst unit is operating.
lNever block the safety valve.
lNever use outside when raining.
lSwitch off and wait for 2 minutes before removing
filler cap to refill boiler.
lDo not overfill.
lAllow to cool completely before emptying boiler.
lDo not stand on boiler or hose.
lDo not drag or try to move boiler by pulling either
the hose or the mains lead.
lDo not allow water or steam to enter light switches or
power points.
lDo not leave unattended.
lUse only standard tap water. Never add detergents or chemicals.
lExtreme care must be taken if the unit is used in
bathrooms. Always be aware of danger of
electrocution from stored water in baths and sinks.
lNever change tools when the unit is operating.
lAlways store upright.
lDo not overfill the reservoir.
lIt is recommended that a RCD (residual current device) rated at
30mA is fitted into the mains supply socket for added protection
against electric shock.
lUse only genuine manufacturer’s parts.
lWarning: hot liquid or steam can burn. Steam may also condense
into boiling droplets. Steam should not be directed towards
electrical appliances (e.g. the inside of an oven).
lThe equipment must be unplugged after use and
before cleaning.
lThis appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
B40 02-08.qxd 25/7/08 10:33 am Page 2
Just before full steam production a small amount of bubbling and water will occur at the steam plate.
Beware of hot water discharge prior to steam emission.
STRIPPING: Remember to check a small area first.
Operation is simple for both right and left handed people.
Simply hold the steam plate flat against the wallpaper for approx. 10 seconds. Now move the plate to
the spot immediately next to the one just steamed - from which the paper should now easily come
away with a little help from a wallpaper scraper.
Working this way should enable continuous paper removal although it may be necessary to steam for
longer periods with some papers, or if not completely removed first time.
Operate steamer until water level is low, then unplug unit and allow to cool for at least 2 minutes before removing filler
cap - Beware of steam - and re-filling unit. When finished, allow to cool completely and empty unit. Always store unit
empty.
SAFETY CUT-OUT
A safety cut-out is fitted to prevent overheating the element if the water boils low. If unit stops boiling during use this
may be the cause. Wait for 2 minutes before removing filler cap then re-fill with water. The cut-out will self reset and
steam be produced again within 5-15 minutes.
The cut-out will not protect the element if a part filled unit is tilted during use in a way which enables part of the
element to be out of the water for longer than 15-20 seconds.
OTHER USES FOR THE STEAM PLATE
Artex®- Normally Artex®can be removed using the same method as for wallpaper although the steaming time will be
longer. CAUTION: Some textured finishes may contain asbestos which may be hazardous to health and which are
subject to licensing controls operated by the HSE (Health & Safety Executive).
Vinyl Floor Tiles - Vinyl floor tiles can also be removed if the plate is left long enough for the heat to penetrate the
adhesive. Once the adhesive is hot it softens and the tile can be peeled from the floor.
Sterilising Soil - To sterilise soil in seed trays or greenhouses rake the soil to obtain a fine
surface. Leave the steam plate on each section, for 2 to 2.5 minutes which should ensure that
the steam has penetrated through the surface.
Killing Weeds - Steam will kill weeds on paths and patios without the use of chemicals. You will
need to steam the weeds for 1 to 1.5 minutes in order to kill them.
SMALL STEAM PLATE
(Optional Accessory - Not included in all kits)
DANGER FROM STEAM. Always be aware that steam is being produced whilst the tool
is in operation. Always wear a protective glove when using.
This tool can be used to strip wallpaper in awkward areas, ie around door frames and in
corners etc. Use similarly to the large steam plate, steaming one area whilst stripping a
previously steamed area. This will ensure quick efficient removal of the wallpaper.
JET NOZZLE CLEANER
(Optional Accessory - Not included in all kits)
IMPORTANT Always check the suitability of materials before steam cleaning. Steam is being
generated at 100ËšC. Do not use on any surfaces that cannot stand this temperature
e.g. Draylon®, delicate fabrics etc. Always test a small area of the material - preferably a
portion that is normally unseen - and allow to dry before starting the full cleaning task. Do
not soak materials being cleaned. Only light application of steam is required.
ASSEMBLING THE TOOL
The Universal Handle (AC302) is used in conjunction with the Jet Nozzle Cleaner. Align the outline
triangle on the handle with the triangle on the accessory. Push the handle into the accessory and
twist so that the solid triangles on the handle and accessory are aligned (see Diagram 1).
Over time, you may find that your steam cleaning accessories become awkward to assemble to the
universal handle. This is due to the steam reducing the lubrication properties of the ‘O’ ring seals. In
this event, simply lubricate the ‘O’ ring seals as illustrated (Diagram 2) using washing-up liquid or
furniture polish.
OPERATING THE TOOL
Connect the universal handle to the jet nozzle head. Select the scraper head or brush to fit the
nozzle end if required and push on to the nozzle.
PIug the boiler unit in and wait for steam to appear at the accessory head. Beware of hot
water discharge prior to steam emission.
This accessory can be used for cleaning all round the house, stoves, cupboards, work
surfaces, toilets, sinks, lawnmowers etc. It both cleans and disinfects at the same time.
It can also be used to defrost your freezer in minutes with no inconvenience. Check with
fridge/freezer manufacturer for advice
before use.
3
Strips hard to reach areas
Diagram 1
Assembling Handle
Diagram 2 Seal Lubrication
Cleans lawnmowers De-frosts freezers
B40 02-08.qxd 25/7/08 10:33 am Page 3


Product specificaties

Merk: Earlex
Categorie: Behangafstomers
Model: SS77

Heb je hulp nodig?

Als je hulp nodig hebt met Earlex SS77 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Behangafstomers Earlex

Earlex

Earlex SS77 Handleiding

4 Oktober 2022

Handleiding Behangafstomers

Nieuwste handleidingen voor Behangafstomers