DSC HS2LCDWFP9 Handleiding

DSC Toegangscontrolesysteem HS2LCDWFP9

Lees hieronder de 📖 handleiding in het Nederlandse voor DSC HS2LCDWFP9 (79 pagina's) in de categorie Toegangscontrolesysteem. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/79

HS2LED/HS2ICON(P)(RF)X/HS2LCD(RF)(P)X V1.3

Installation Instructions/Instructions d’installation/Instrucciones de

instalación/Instruções de instalação English, Français, Español, Português

29009811R002

Introduction

The HS2LED/HS2ICN(P)(RF)x/HS2LCD(RF)(P)x keypads are compatible

with the PowerSeries Neo HS2016/32/64, HS2016-4* and HS2128 panels.

The RF keypads combine a wireless transceiver with the respective HS2

keypad.

*Model not UL/ULC listed.

Specifications

lTemperature range: -10°C to +55°C (14°F to 131°F); UL/ULC: 0°C

to +49°C (32°F to 120°F)

lHumidity (MAX): 93%R.H. non-condensing

lPlastic enclosure protection degree: IP30, IK04

lVoltage rating: 13.8Vdc nominal (power provided by the compatible

control panel)

lConnects to control panel Corbus via 4 wires

l1 configurable zone input or PGM output*

lHS2LED/ HS2ICN(P)/HS2LCD(P)/HS2ICNRF(P)/HS2LCDRF(P)

Current draw:55mA(min)/105mA(max)

lWall-mount tamper

l5 programmable function keys

lReady (Green LED), Armed (Red LED), Trouble (Yellow LED),

AC (Green LED)

lDimensions (L x W x D): 168mm x 122mm x 20 mm

lWeight: 260g

lLow temperature sensor

lFrequency: 433 MHz (HS2ICNRF4/HS2LCDRF4)

l868 MHz (HS2ICNRF8/HS2LCDRF8)

l912-919MHz (HS2ICNRF9/HS2LCDRF9)

lUp to 128 wireless zones

Zone not to be programmed as Fire type or 24h type.

NOTE: Keypads contain no serviceable parts.

NOTE: Only models operating in band 912-919MHz are UL/ULC listed.

Unpack

The keypad package includes the following:

HS2LED/ICN(RF)/LCD(RF) HS2ICN(RF)P/LCD(RF)P

1 keypad 1 keypad

4 mounting screws 4 mounting screws

2 end-of-line resistors 2 end-of-line resistors

Keypad inner door labels Keypad inner door labels

1 tamper switch 1 tamper switch

Installation Instructions Installation Instructions

Mini Proximity (prox) tag (MPT)

Table 1: Compatible Devices

Wireless PG smoke detector PGx926UL

Wireless PG smoke and heat detector PGx916UL

Wireless PG CO detector PGx913

Wireless PG PIR moti on detector PGx904(P)UL

Wireless PG PIR + camera motion detector PGx934(P)UL

Wireless PG curtain motion detector PGx924UL

Wireless PG dual tech motion detector PGx984(P)

Wireless PG mirror motion detector PGx974(P)UL

Wireless PG outdoor motion detector PGx994UL

Wireless PG glass break detector PGx912/PGX922 UL

Wireless PG shock detector PGx935UL

Wireless PG flood detector PGx985UL

Wireless PG temperature detector (indoor) PGx905UL

Outdoor temperature probe (requires PGx905) PGTEMP-PROBE

Wireless PG key PGx939UL

Wireless PG key PGx929UL

Wireless PG panic key PGx938UL

Wireless PG 2-button key PGx949UL

Wireless PG indoor siren PGx901UL

Wireless PG outdoor siren PGx911UL

Wireless PG repeater PGx920UL

Wireless PG door/window contact PGx975UL

Wireless PG door/window contact w/AUX PGx945UL

NOTE: In this chart, x in the model number represents the operating fre-

quency of the device as follows: 9 (912-919 MHz), 8 (868MHz), 4

(433MHz).

NOTE: Only models operating in the band 912-919 MHz are UL/ULC or

cUL listed where indicated. Only UL approved devices are to be used

with UL/ULC listed systems.

Mount the Keypad

Mount the keypad where it is accessible from designated points of entry

and exit. Once a dry and secure location has been selected, perform the fol-

lowing steps to mount the keypad.

Disassemble Keypad

Insert the tip of a flat-head screwdriver into the slots at the bottom left

and right of the keypad.

Gently pry open the faceplate. This will remove it and allow access for

mounting.

Mount and Wire Keypad

1. Secure keypad to wall using mounting holes. Use all four screws

provided unless mounting on a single gang box. Use the plastic anchors

supplied if the unit is to be mounted on drywall.

2. If using the keypad tamper, secure the tamper plate to the wall with a

screw.

NOTE: For UL/ULC listed commercial burglary installations, the use of

the keypad tamper is mandatory.

3. Run wire through wiring slot or knockouts. Connect Corbus and

PGM/Zone wiring to keypad. Place tamper switch into tamper hole on

backplate.

4. Place keypad into backplate, ensuring the wire is pushed back into the

wall as much as possible. Route the wire inside the keypad, ensuring high

components are avoided. Snap the front assembly closed, ensuring that

there is no pressure to the keypad from the wire below.

Product specificaties

Merk:	DSC
Categorie:	Toegangscontrolesysteem
Model:	HS2LCDWFP9
Kleur van het product:	Wit
Breedte:	168 mm
Diepte:	122 mm
Hoogte:	25 mm
Internationale veiligheidscode (IP):	IP30
Connectiviteitstechnologie:	Draadloos
Type stroombron:	Batterij/Accu
Met slot:	Ja
Frequentie:	915 MHz
Stroomverbruik:	105 mA
Draadloze verbindingen:	Ja
Afmetingen (B x D x H):	168 x 122 x 25 mm
Bedrijfstemperatuur (T-T):	-10 - 55 °C
Relatieve vochtigheid in bedrijf (V-V):	5 - 93 procent
Batterijtechnologie:	Alkaline
Slot type:	Sleutel
Stroom in standby:	30 mA
Tamper-schakelaar:	Ja