Drayton Digistat+3RF Handleiding

Drayton Thermostaat Digistat+3RF

Lees hieronder de 📖 handleiding in het Nederlandse voor Drayton Digistat+3RF (2 pagina's) in de categorie Thermostaat. Deze handleiding was nuttig voor 67 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/2
Drayton
Digistat +3RF
Invensys Controls Europe
Customer Service Tel: 0845 130 5522
C ustomer Service Fax: 0845 130 0622
Technical Helpline Tel: 0845 130 7722
Website: www.draytoncontrols.co.uk
Email: customer.care@invensyscontrols.com
User Guide 06490098001 IssA
Programmable Room
Thermostat Wireless
5-2 Day / 7 Day
Model: RF701/22092
Power Supply:
Battery - Thermostat
Mains - Digistat SCR
The Digistat +3RF thermostat is a programmable thermostat
5-2 Day / 7 Day product. 5–2 day allows you to set a program for
weekdays and a program for the weekend. Full 7-day functionality
allows you to set a different program for every day of the week.
Each program type allows you to set 6 time and temperature events.
Clock Setting
Your Digistat +3RF is fitted with a real-time clock, which is pre-set
at the factory. You will not have to alter the time settings.
A special feature of this real-time clock is to automatically update
the time during the summer/winter time change removing the
need to manually alter the clock.
General Operation
With the unit in Auto mode (the small arrow to bottom of screen
will point to Auto) the temperature can be changed for a short
time by using the + or - buttons. Changing the temperature in
this way will keep the Digistat +3RF set to your new temperature
until the next pre-programmed event (at which time it will revert
to programmed temperature). The temperature you are setting
will flash on the screen. Once temperature is set, the unit will
revert to showing the current temperature. The indicator will
show on the screen if the heating is turned on.
User Instructions
The Digistat +3RF thermostat is a programmable thermostat
5-2 Day / 7 Day product. 5–2 day allows you to set a program for
weekdays and a program for the weekend. Full 7-day functionality
allows you to set a different program for every day of the week.
Each program type allows you to set 6 time and temperature events.
Digistat +3RF
Pre-set Program
Your Digistat +3RF comes with the following default settings
pre-programmed for your convenience:
Basic Settings
Your Digistat +3RF
Controls and Display Layout
What is a programmable room thermostat?
...an explanation for householders
A programmable room thermostat is both a programmer and a room
thermostat. A programmer allows you to set ‘On’ and ‘Off ’ time
periods to suit your own lifestyle. A room thermostat works by sensing
the air temperature, switching on the heating when the air
temperature falls below the thermostat setting, and switching it off
once this set temperature has been reached.
So, a programmable room thermostat lets you choose what times you
want the heating to be on, and what temperature it should reach
while it is on. It will allow you to select different temperatures in your
home at different times of the day (and days of the week) to meet
your particular needs.
Turning a programmable room thermostat to a higher setting will not
make the room heat up any faster. How quickly the room heats up
depends on the design of the heating system, for example, the size of
boiler and radiators.
Neither does the setting affect how quickly the room cools down.
Turning a programmable room thermostat to a lower setting will result
in the room being controlled at a lower temperature, and saves energy.
The way to set and use your programmable room thermostat is to
find the lowest temperature settings that you are comfortable with at
the different times you have chosen, and then leave it alone to do its
job. The best way to do this is to set low temperatures first, say 18 o
C,
and then turn them up by one degree each day until you are
comfortable with the temperatures. You won’t have to adjust the
thermostat further. Any adjustments above these settings will waste
energy and cost you more money.
If your heating system is a boiler with radiators, there will usually be only
one programmable room thermostat to control the whole house. But you
can have different temperatures in individual rooms by installing
thermostatic radiator valves (TRVs) on individual radiators. If you don’t
have TRVs, you should choose a temperature that is reasonable for the
whole house. If you do have TRVs, you can choose a slightly higher
setting to make sure that even the coldest room is comfortable, then
prevent any overheating in other rooms by adjusting the TRVs.
The time on the programmer must be correct. Some types have to be
adjusted in spring and autumn at the changes between Greenwich
Mean Time and British Summer Time.
You may be able to temporarily adjust the heating programme, for
example, ‘Override’, ‘Advance’ or ‘Boost’. These are explained in the
manufacturer’s instructions.
Programmable room thermostats need
a free flow of air to sense the temperature,
so they must not be covered by curtains
or blocked by furniture. Nearby electric
fires, televisions, wall or table lamps
may prevent the thermostat from
working properly.
(Fig 3)
How to replace the batteries see fig 3.
Remove the battery cover using a coin. Replace the spent
batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries ensuring
correct orientation. Replace the battery cover pressing fully home.
(Fig 1) (Fig 2)
How do I know when to change the batteries.
When the batteries start to run low a battery icon will flash in the
display, to indicate “low battery” during this time the Digistat +3RF
will function normally (see fig 1).
Please replace batteries with 2 x 1.5V IEC LR6 (AA) Alkaline batteries.
When the battery icon alone is shown in the display, the batteries
are completely exhausted and the Digistat +3RF will cease to
function (see fig 2). Re-activate by replacing the batteries.
Drayton
Digistat +3RF
Certification Mark
D
ig is ta t+3RFDigi st a
t+3R
F
Dra
yton
D
ra y
ton
D
ra y
ton
Dig is tat+3RFD
ig is tat+3RF
Drayton
Event 1 2 3 4 5 6
Time 6:30 8:30 12:00 14:00 16:30 22:30
Temperature 20.0 16.0 16.0 16.0 21.0 7.0
Event 1 2 3 4 5 6
Time 7:00 9:00 12:00 14:00 16:00 23:00
Temperature 20.0 18.0 21.0 18.0 21.0 7.0
1 2 3 4 5 6
25ÂșC
20ÂșC
15ÂșC
10ÂșC
5ÂșC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period Monday-Friday
Room Temp
1 2 3 4 5 6
25ÂșC
20ÂșC
15ÂșC
10ÂșC
5ÂșC
07:00 09:00 12:00 14:00 16:00 23:00
Time Period Saturday-Sunday
Room Temp
Pre-set Program 1 (9 til 5)
Monday-Friday
Saturday-Sunday
Weekday
Weekend
As you can see, at 06:30 , the heating will come on to raise the
temperature to 20ÂșC. A 08:30, the temperature set point is droppedt
from 20ÂșC down to16ÂșC, it stays at 16ÂșC throughout the day, until
16:30 when the temperature increases to 21ÂșC. The temperature
then drops down to a night-setback temperature of 7ÂșC until 06:30
when the cycle repeats for the next day. (Monday to Friday) or
changes to weekend setting see below.
As you can see, at 07:00, the heating will come on to raise the
temperature to 20ÂșC. At 09:00, the temperature set point is
dropped from 20ÂșC down to18ÂșC, it stays at 18ÂșC until 12:00 when
the heating comes on to raise the temperature to 21ÂșC. The
temperature stays at 21ÂșC until 14:00 when it drops down to 18ÂșC.
At 16:30 the heating comes on to raise the temperature to 21ÂșC
where it stays until 23:00 when the temperature then drops down
to a night-setback temperature of 7ÂșC until 07:00 when the cycle
repeats for the next day. (Saturday and Sunday) or changes to
weekday settings see above.
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
3. Once time has been set,
press and use the
+ or - buttons to adjust
required temperature.
Repeat the above steps
2-3 until the 6 periods
have been set for Monday
To adjust the times and temperatures for 7-Day
operation:
1. With the product operating
as normal in the Auto mode
press once and then
press the + button until the
display is flashing and shows.
2. Press the once, the
display will be as shown. The
time will be flashing, use the
+ or - buttons to adjust the
1st time as required.
To adjust the times and temperatures for 5-2 Day
operation:
2. Press the once, the
display will be as shown. The
time will be flashing, use the
+ or - buttons to adjust the
1st time as required.
3. Once time has been set,
press and use the
+ or - button to adjust
required temperature
(shown flashing).
Press to confirm and
move to the next time and
temperature periods to be
adjusted confirming changes
by pressing button.
(max 6 periods).
4. Once the last weekday
temperature has been set
press once to confirm
settings and allow adjustment
of the weekend program.
Use the + and – butons and
the button to set the 6
periods for the weekend program.
5. Once the final temperature
has been set press to
confirm setting. To exit press
or until you
return to auto mode with the
bottom arrow pointing at Auto.
(* small 1 in lower half of screen
shows which time period is being set
e.g. 1=1st period, 2 = 2nd period etc)
Congratulations!
The unit is now set correctly to follow your required timings.
Congratulations!
The unit is now set correctly to follow your required timings.
4. Once Monday has been set,
press once.
Repeat steps 2-3 until all
7 days of the week have
been set.
5. Once the final temperature
has been set press the
to confirm settings. To exit
press or until
you return to auto mode with
the bottom arrow pointing
at Auto.
1. With the product operating
as normal in the Auto mode
press once and then
press the + button until the
display is flashing and shows.
A flashing flame indicates the product is in intelligent delayed
start mode (see special note).
06490098001 IssA 24-1-07 13/2/07 12:04 Page 1
(Fig 12)
If you wish to change any User Options (shown in table 1) they can
be accessed from Auto or Man by pressing < and > simultaneously
for 3 seconds. Once you have accessed the User Options Menu (Fig
4) press > to scroll through selectable options. The settings for
each option can be changed by pressing + or - as required. Press >
to accept the change and move to the next option. To exit press <
and > simultaeously for 3 seconds. Alternatively, not pressing any
buttons for 2 mins will cause the Digistat +3RF to return to Auto.
(Fig 5) shows option 01 24 (24 hour clock).
Only selected options that have been accepted by pressing > will
be changed.
To set holiday mode:
1. Press twice, the display
shows time flashing.
Time periods between 1 to
23(Hr)hours and 1 to
199(d)days can be set.
2. Press + or - buttons to
adjust the count down time
as required. Press once,
the display will show
temperature flashing
Weekdays
As you can see, at 06:30, the heating will come on to raise the
temperature to 21°C.
At 08:30, the temperature set point is dropped to 16°C, it stays at
16°C until 12:00 when the heating comes on to raise the
temperature to 21°C. The temperature stays at 21°C until 14:00
when it drops to 16°C. At 16:30 the heating comes on to raise the
temperature to 21°C where it stays until 22:30 when the
temperature drops down to a setback temperature of 10°C until
06:30 when the cycle repeats the next day.
To switch OFF the thermostat:
Press the + and – simultaneously for 5 seconds until the OFF is
displayed.
The thermostat and heating system will now be OFF unless the
temperature in the controlled space falls below 7°C, the frost
protection set point. Please note this does not affect the
operation of the domestic hot water where provided.
To switch ON the thermostat, press any key to return to auto mode.
Weekends
As you can see, at 7:00, the heating will come on to raise the
temperature to 21°C.
At 9:00, the temperature set point is dropped to 18°C, it stays
at 18°C until12:00 when the heating comes on to raise the
temperature to 21°C. The temperature stays at 21°C until 14:00
when it drops down to 18°C. At 16:30 the heating comes on to
raise the temperature to 21°C where it stays until 23:00 when
the temperature drops down to a setback temperature of 10°C
until 07:00 when the cycle repeats the next day.
Weekends
As you can see, at 7:00, the heating will come on to raise the
temperature to 21°C.
At 9:00, the temperature set point is dropped to 18°C, it stays
at 18°C until12:00 when the heating comes on to raise the
temperature to 21°C. The temperature stays at 21°C until 14:00
when it drops down to 18°C. At 16:30 the heating comes on to
raise the temperature to 21°C where it stays until 23:00 when
the temperature drops down to a setback temperature of 16°C
until 07:00 when the cycle repeats the next day.
User Options
3. Press + or - buttons to
adjust temperature and press
to start holiday count
down time. Alternatively after
10 seconds the temperature
will stop flashing and holiday
count down time will start.
Display shows count down
time and ambient room
temperature.
4. To exit the holiday mode
press the or
once, to return to auto.
User
options What is it Min Max Default
01 Change 12h or 24h clock 12 24 24
02 Change to another
pre-set programme 1 3 1
03 Change the number of
programme events per day 2, 4 or 6 6
04 Switch on/off automatic
summer/winter time change On Off On
05 Adjust date and time Factory Set
06 Change temperature offset
0
C -5 5 0
07 Restore pre-set programme On Off Off
08 To disable Off function On Off On
09 Access protection lock On Off Off
(Table 1)
(Option 01)
How to change from 24hr to 12hr clock.
Enter user options, select option 01 and use + and – keys to select
desired option, 12 = 12hr and 24 = 24hr. Press > to accept change.
(Option 02)
How to change to another predefined program 1, 2 or 3.
Enter user options, select option 02 and use + and – keys to
select desired program 1, 2 or 3. 1 = program 1, 2 = program 2
and 3 = program 3. Press > to accept desired change.
Preset programs 2 and 3 are shown below:
(Option 03)
How to change the number of program events per day.
Enter user options, select option 03 and use + and – keys to
select desired option. 2 = 2 time / temp events per day, 4 = 4
time / temp events per day and 6 = 6 time / temp events per
day. Press > to accept desired change.
(Option 04)
How to switch on/off the automatic summer / winter time
change.
Twice a year the actual time is automatically changed to keep it
in line with the summer / winter time change. Default setting is
On. If you wish to disable / enable this feature enter user
options, select option 04 and press – or + key to display Off or
On as desired. Press > to accept desired change.
(Fig 11)
To set a constant room temperature (Manual mode):
1. Press once, the display
shows temperature flashing
(example
20
0
C)
2. Press + or - buttons to
adjust the temperature as
required. The temperature
will stop flashing after 5
seconds and start controlling
at this temperature
3. To exit manual mode press
once, to return to auto.
To change temperature for a short period (Override):
1. Press + or - buttons to
adjust set temperature. Set
temperature shown flashing
2. After 5 seconds will start
controlling at selected set
point but displays actual room
temperature. 2 chrevons
indicates override mode.
3. To exit override press
once or wait until next change
in the pre-set program.
Event 1 2 3 4 5 6
Time 6:30 8:30 12:00 14:00 16:30 22:30
Temperature 21.0 16.0 21.0 16.0 21.0 10.0
Event 1 2 3 4 5 6
Time 7:00 9:00 12:00 14:00 16:30 23:00
Temperature 21.0 18.0 21.0 18.0 21.0 10.0
1 2 3 4 5 6
25ÂșC
20ÂșC
15ÂșC
10ÂșC
5ÂșC
06:30 08:30 12:00 14:00 16:30 22:30
Time Period Monday-Friday
Room Temp
1 2 4 5 63
25ÂșC
20ÂșC
15ÂșC
10ÂșC
5ÂșC
07:00 09:00 12:00 14:00 16:30 23:00
Time Period Saturday-Sunday
Room Temp
Pre-set Program 2 (Home for lunch)
Monday-Friday
Saturday-Sunday
Weekday
Weekend
Date and time setting.
Digistat +3RF comes with a pre-set clock, which also
automatically adjusts for summer/winter time changes. It is
activated automatically on 1st installation. There should be no
need to change these settings, however, should you wish to, it
can be done in Option 05.
(Option 05)
How to adjust date and time.
Enter user options, select option 05 (fig 6)
To change the year press > once (fig 7)
To change the month press > again (fig 8)
To change the day press > again (fig 9)
To change the time press > again (fig 10)
Once you have selected your required display, to adjust press +
or - and > to accept change.
To select option 06 press > until option 06 display is shown (fig 11)
Event 1 2 3 4 5 6
Time 6:00 8:30 12:00 14:00 17:30 22:30
Temperature 21.0 19.0 21.0 19.0 21.0 16.0
Event 1 2 3 4 5 6
Time 7:00 9:00 12:00 14:00 16:30 23:00
Temperature 21.0 18.0 21.0 18.0 21.0 16.0
123456
25ÂșC
20ÂșC
15ÂșC
10ÂșC
5ÂșC
0 6:00 08:30 12:00 14:00 17:30 22:30
Time Period Monday-Friday
Room Temp
1 2 3 4 5 6
25ÂșC
20ÂșC
15ÂșC
10ÂșC
5ÂșC
0 7:00 09:00 12:00 14:00 16:30 23:00
Time Period Saturday-Sunday
Room Temp
Pre-set Program 3 (Home Worker)
Monday-Friday
Saturday-Sunday
Weekday
Weekend
Weekdays
As you can see, at 06:00, the heating will come on to raise the
temperature to 21°C.
At 08:30, the temperature set point is dropped to 19°C, it stays at
19°C until 12:00 when the heating comes on to raise the
temperature to 21°C. The temperature stays at 21°C until 14:00
when it drops to 19°C. At 17:30 the heating comes on to raise the
temperature to 21 where it stays until 22:30 when the°C
temperature drops down to a setback temperature of 16°C until
06:00 when the cycle repeats the next day.
(Fig 10)
(Fig 9)
(Fig 8)
(Fig 7)
(Fig 6)
(Fig 4) (Fig 5)
(Option 06)
How to change temperature offset.
The temperature displayed on the thermostat may not match that
of other temperature measuring devices in the controlled space,
because of its location. The displayed temperature may be offset to
bring it in line with other devices. To adjust the temperature, enter
the user options, select option 06. The temperature may be offset
by +/- 5 degrees by pressing the + and – keys. Press > to accept the
desired change.
(Option 07)
How to restore the built in time temperature programs.
Enter user options, select option 07 and use + and – keys to select
desired option. Off = current programs retained. On = restore
factory program settings. Press > to select the desired change. The
option 07 display automatically reverts back to off. Please note
enabling this function will lose any user changes to the preset
programs.
(Option 08)
How to disable the OFF function.
To disable the OFF function, enter user options, select option 08
and use + or – keys to select Off. Press > to accept change.
It is now not possible to switch the Digistat+3RF OFF using the +
and- keys as previously described. To enable the OFF function
return to option 08 and select ON. Press > to accept change.
(Option 09)
How to lock the key pad - Access Protection Lock.
The access protection lock allows you to lock the Digistat +3RF so
that it cannot have any adjustments.
The default is OFF mode allowing you to adjust the Digistat +3RF.
To Lock the Digistat +3RF settings enter the User Options Menu
Option 09 and select On and press > to accept.
Once the User Options Menu is exited all buttons will be locked.
To switch off the Protection Lock enter the User Menu and change
to OFF. Press > to accept.
Once the User Menu is exited all buttons will be free to adjust.
Special Note:
The following only applies when the Intelligent delayed start
feature is enabled by the installer.
When the delay period is operating indicated by the flame symbol
flashing (Fig12), pressing any button returns the Digistat +3RF to
auto mode allowing normal button operation until the next time/
temperature event, when it will resume the delay start mode or
follows the Holiday, Manual, Override or Off modes as selected.
Changes to the installer options and pre-set programmes must be
made with the flame symbol not flashing.
What is Intelligent delayed start.
The Intelligent Delayed Start is an energy saving feature which
automatically reduces the warm up time for the heating system. As
the weather becomes milder, Intelligent Start will delay the heating
start times so that the fuel is not wasted bringing the room up to
temperature earlier than necessary.
06490098001 IssA 24-1-07 13/2/07 12:04 Page 2

Product specificaties

Merk: Drayton
Categorie: Thermostaat
Model: Digistat+3RF

Heb je hulp nodig?

Als je hulp nodig hebt met Drayton Digistat+3RF stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Thermostaat Drayton

Drayton

Drayton Digistat RF902 Handleiding

21 Augustus 2024
Drayton

Drayton Digistat RF901 Handleiding

21 Augustus 2024
Drayton

Drayton PTS1 Handleiding

21 Augustus 2024
Drayton

Drayton LP20RF & Digistat+ RF Handleiding

21 Augustus 2024
Drayton

Drayton Easy 2 Handleiding

21 Augustus 2024
Drayton

Drayton Digistat+1RF Handleiding

21 Augustus 2024
Drayton

Drayton Digistat+C RF Handleiding

21 Augustus 2024
Drayton

Drayton HTS3 Handleiding

21 Augustus 2024
Drayton

Drayton Digistat 2290B Handleiding

21 Augustus 2024
Drayton

Drayton Digistat 22902 Handleiding

21 Augustus 2024

Handleiding Thermostaat

Nieuwste handleidingen voor Thermostaat

Techno Line

Techno Line TM 3010 Handleiding

18 November 2024
Ferguson

Ferguson FS1TH Handleiding

17 November 2024
EQ-3

EQ-3 HM-RC-19 Handleiding

16 November 2024
EQ-3

EQ-3 CC-RT-N Handleiding

16 November 2024
Delta Dore

Delta Dore TYDOM 1.0 Handleiding

16 November 2024
Delta Dore

Delta Dore Tybox 5701 FP Handleiding

16 November 2024
Delta Dore

Delta Dore Tybox 33 Handleiding

16 November 2024
Delta Dore

Delta Dore Tybox 5702 FP Handleiding

16 November 2024
Delta Dore

Delta Dore Tybox 31 Handleiding

16 November 2024
Delta Dore

Delta Dore TYBOX 827 W RF Handleiding

16 November 2024