Dormakaba RCI GateMag 8380 Handleiding

Dormakaba Niet gecategoriseerd RCI GateMag 8380

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba RCI GateMag 8380 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
INSTALLATION
RCI GateMag 8380®
Z BRACKET & POST BRACKET
ELECTROMAGNETIC LOCK ACCESSORY
© 2019 dormakaba Canada Inc
www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com
1. Installation of this product should be done by an experienced
installer with knowledge of this product. Read and conform to
each of the Pre-Installation Instructions supplied with your RCI
brand 8380 GateMag®. Failure to conform to the Pre-Installation
Instructions is a misuse of product and could result in serious
bodily injury or property damage. This product must be used only
with an RCI brand 8380 GateMag®.
2. Back mount 8380 GateMag® to stationary post for single gate or
to fixed leaf of gate for double-swing gate per template STEP 2.
3. Using a hammer install the clinch nut into the center hole of
bracket (A) from the back side as shown below.
4. Assemble bracket (A) & bracket (B) together to form a “Z” using
2 screws in each slot. Do not over tighten to allow adjustment.
5. Pass bolt with rubber head through the armature plate. Add 3
washers (steel - rubber - steel) onto bolt. Carefully apply thread
locking compound to the exposed threads. While aligning pins,
drive the bolt into clinch nut on bracket A.
NOTE: Do not over tighten armature plate. It must remain
movable to allow surface alignment with electromagnetic lock.
6. With gate in closed position, carefully align armature plate to
GateMag®’s electromagnetic face. Secure Z bracket assembly to
swinging portion of gate. Make sure there is good contact of lock
with armature plate and tighten adjustment screws.
Washers
(steel-rubber-steel)
M8 Clinch Nut
Armature Adjustment
Bracket A
M5 Counter Sunk Screws
(6 places)
Armature Plate
Armature Bolt
Door Bracket B
Note For proper operation, one :
side of the double gate pair
should be stationary. Lock may
not hold correctly if both gates
swing freely.
1. Installation of this product should be done by an experienced installer with knowledge of this
product. Read and conform to each of the Pre-Installation Instructions supplied with your
RCI brand 8380 GateMag®. Failure to conform to the Pre-Installation Instructions is a
misuse of the product and could result in serious bodily injury or property damage.
This product must be used only with an RCI brand 8380 GateMag ®.
2. Side mount 8380 GateMag® to stationary post per template STEP 2.
3. Using a hammer install the clinch nut into the center hole of the bracket from the backside.
4. Pass bolt with rubber head through the armature plate. Add 3 washers (steel - rubber - steel) onto bolt.
Carefully apply thread locking compound to the exposed threads. While aligning pins, drive the bolt into clinch nut.
5. With gate in closed position, carefully align armature plate to GateMag®’s electromagnetic face.
Secure the bracket to post of sliding gate as required.
Sliding Gate Post Bracket Installations
Swinging Gate “Z” Bracket Instructions
WARNING: Improper installation, maintenance, inspection or use of this or any related product may cause the electromagnet lock, armature plate
and associated hardware to disengage and fall, causing serious bodily injury and property damage. dormakaba Canada Inc. and/or dormakaba
USA Inc.will not be liable to the installer, purchaser, end user or anyone else for damage or injury to person or property due to improper installa-
tion, care, storage, handling, maintenance, inspection, abuse, misuse or act of God or nature involving this or any related product.
NOTE: Not to scale. Specifications are subject to change without notice.
ISTJPB80-2 PCN18041
R09-19GR


Product specificaties

Merk: Dormakaba
Categorie: Niet gecategoriseerd
Model: RCI GateMag 8380

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba RCI GateMag 8380 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Dormakaba

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd