Dormakaba RCI F1114 Handleiding

Dormakaba Niet gecategoriseerd RCI F1114

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba RCI F1114 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 27 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

INSTRUCTIONS

1. To determine if the Strike Shim positions need adjustment, measure dimension “R” (see Figure 1) from the center to the edge

of the latch. When necessary rearrange Strike Shims according to the chart below. The “shipped as default” positions are

illustrated in Figure 2.

SHIM PLACEMENT CHART

Note: Shims consist of two thin and one thick. Install with the indicated hardware per the appropriate measurement R range.

Fig. 1

I N S T A L L A T I O N

www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: sales@rutherfordcontrols.com

When installing an electric strike on an inactive door of a set of double doors, it can be treated the same as a frame installation in most situations. For

more information contact the Technical Service Department at 1-800-265-6630 or 519-621-7651.

Fire labeled heavy-duty electric strike

F1114

isf1114 Pcn14079

r06/15Gr

Fig. 2

Measurement “R” “S1” Shims “S1” Screws “S2” Shims “S2” Screws

5/16” (8.2mm) or Less None M4 x 10mm 1 thick, 2 thin M4 x 10mm

5/16” - 3/8”, (8.2 - 9.7mm) 1 thin M4 x 10mm 1 thick, 1 thin M4 x 10mm

3/8” - 7/16”, (9.7 - 10.7mm) 1 thick M4 x 10mm 2 thin M4 x 10mm

7/16” - 1/2”, (10.7 - 12.2mm) 1 thick, 1 thin M4 x 14mm 1 thin M4 x 10mm

1/2” - 9/16” (12.2 - 13.7mm) 1 thick, 2 thin M4 x 14mm none none

S1 S2

Shipped as Default

“R” distance

from center to

edge of latch

“R” distance from

center to edge of latch

Deadlock

Trigger

Deadlock

Trigger

Mortise Lock Cylindrical Lock

2. Determine the horizontal centerline.

FOR MORTISE LOCKS: Position the strike against the edge

of the door with the deadlock trigger fully on the strike’s

angled ramp and the latch within the strike cavity. Move

door close to the frame. The horizontal centerline is clearly

molded into the strike’s pry-guard. Transfer onto door frame.

FOR CYLINDRICAL LOCKS: Simply align the center of the

latch with the center of the strike cavity. Move door close

to the frame. The horizontal centerline is clearly molded

into the strike’s pry-guard. Transfer onto door frame.

3. Determine the vertical centerline of the door lock face,

carefully considering any stops or gasket and transfer onto

the door frame.

4. Use the vertical and horizontal centerlines marked on the

drawing below to prepare the door frame for cutting.

5. If required, install the optional “no weld” mounting

tabs.

6. Connect the incoming wiring from the power supply to

the terminal screws on the strike insert. RCI door strikes

are not polarity sensitive although be certain to observe

proper polarity if a suppression diode is required for access

control applications. To meet BHMA A156.31 install the

MOV provided across the red & black power wires.

Install the door strike in the door frame using the screws provided.

8. See Installation Tips on page 3.

I N S T A L L A T I O N

Fire labeled heavy-duty electric strike

F1114

www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: sales@rutherfordcontrols.com

INSTRUCTIONS Cont’d.

In or Out... we make it Easy!®

NOTE: Specifications subject to change without notice.

* Dimension F is measured from face of mounting tab to face of frame.

MEASUREMENT

FRACTIONAL

INCHES

DECIMAL

INCHES

METRIC

A 1-1/4” 1.25 31.8

/B 4-7 8” 4.87 123.8

C 3-3/8” 3.38 85.7

D 1-1/2” 1.50 38.1

/E 3 8” 0.38 9.5

/F 1 8” 0.13 3.2

G 1-11/16” 1.69 42.9

4-1/K 8” 4.13 104.8

M 12-24 N/A N/A

F1114

Vertical Centre Line of Door

Lock and Mounting Face Plate

Fig. 3

I N S T A L L A T I O N

Fire labeled heavy-duty electric strike

F1114

www.rutherfordcontrols.com • Phone: 1.800.265.6630 • fax: 1.800.482.9795 • e-mail: sales@rutherfordcontrols.com

In or Out... we make it Easy!®

These photos show three simple steps to a quick and easy strike insertion.

iNstallatiON seQueNce tiPs

Frame Preparation:

Should the frame not be cut out

for the F1114, follow the directions

located in Fig 3 on Page 2.

Initial Position:

Place the strike as shown with the

mounting tab located between the

face plate and the insert.

STEP 1

Strike Position:

Rotate the strike into the frame.

Note that the strike is angled

slightly forward to clear the Pry-

Guard.

STEP 2

Final Push:

Push the strike into the frame. The

pry-guard should be behind the

front lip of the frame.

STEP 3

Ready to Secure:

The strike is now in position ready

to be secured by the two (2) 12-24

mounting screws.

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	RCI F1114

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba RCI F1114 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024