Dormakaba RCI 8375 Handleiding

Dormakaba Niet gecategoriseerd RCI 8375

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba RCI 8375 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 156 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

INSTALLATION

RCI 8375

SURFACE MICROMAG® ELECTROMAGNETIC LOCKS

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

IS8375

PCN18041

R03-20GR-1

Pre-Installation Instructions

1. This product must be installed according to all applicable building

and life safety codes.

2. Due to the variety of mounting configurations available with this

product, a survey and assessment of the physical area in which

the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally sound

prior to installation of the electromagnetic lock. The structural

integrity of the mounting surfaces must be strong enough to meet

or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not hinder

or create a potential safety hazard to authorized personnel

accessing the protected area.

6. Because electromagnetic locks are used in a variety of applications

and different door frame configurations, an experienced installer

with knowledge of this product must make a determination of the

optimal mounting method for this specific application.

7. The components, hardware, installation instructions and mounting

template included with this product are intended for use on

outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories not included with this product must be used

in the following applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that do not have a door frame

• Hollow metal or wood frames where the door stop is

not thick enough to allow the product to be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to be

mounted low enough to meet the magnet surface

Refer to the page 4 Product Accessories Guide for further

information. Accessories may impact holding force.

11. Installation of this product should be done by an experienced

installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound be

applied to all screws during installation to reduce chance of screws

loosening over extended time.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

Fig. 1.

8375 Mounting

Plate Removal

Fig. 2 – 8375 Voltage Selection Jumper Setting

12VDC Operation 24VDC Operation

(Factory Setting)

Electromagnetic lock installations must conform to local fire codes, National

building codes and Life Safety Codes.

Mounting

Bracket

Releases captive

mounting screws

NOTE: All dormakaba electromagnetic locks must be powered with

filtered and regulated DC power supplies such as the DKPS Series UL

Listed power supply. dormakaba offers a full line of power supplies and

switching devices that are suitable for use with the 8375 Series locks.

To Ensure Instant Release All switching devices must be wired in

between the DC power source and the positive terminal of the lock in

Fig 3.

Switching the negative power supply line will not allow the lock to

release immediately. dormakaba electromagnetic locks contain MOV’s

for surge suppression and do not require any additional suppression to

be added during installation. The installation of diodes across the lock

input terminals will cause a delay in release.

Fig. 3 – Power Connections

SWITCH

INCORRECT

CORRECT

SWITCH

FILTERED DC SUPPLY

Mount the electromagnetic lock to the door frame as outlined on the

installation template included with the product.

NOTE: During installation of the armature plate to the door it is essential

that the armature plate remains movable. The armature plate must be

allowed to pivot on the center-mounting bolt to allow proper alignment with

the magnet surface. If the plate is not aligned with the magnet surface, the

lock may lose holding force or not lock at all.

The head of the armature mounting bolt ships with a rubber washer affixed

to it. This washer should project slightly beyond the surface of the armature

plate. This is to allow the washer to expand when power is removed and

break the air vacuum between the plate and the magnet surface. If this

washer is removed or trimmed the lock will appear to have some holding

force even when power is removed.

For added safety, thread locking compound has been provided for the armature

plate bolt and the four captive electromagnetic lock mounting screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware to

disengage and fall, causing serious bodily injury and property damage.

dormakaba Canada Inc. and/or dormakaba USA Inc. will not be liable to

the installer, purchaser, end user or anyone else for damage or injury to

person or property due to improper installation, care, storage, handling,

maintenance, inspection, abuse, misuse or act of God or nature involving

this product or any related accessories or parts.

Route the power supply connecting wire through the door frame and into the

wire access hole in the top of the magnet housing. Connecting wire should

be of sufficient gauge for the lock being installed and the distance being run.

Installation Instructions

Inspection and Maintenance

This product and all related accessories or parts must be inspected

and maintained on a . Contacting surfaces of quarterly basis

the electromagnetic lock and armature plate must be kept free of

contaminating materials. Surfaces must be cleaned periodically with a

non-abrasive cleaner.

All mounting fasteners must be inspected on a quarterly basis.

When properly installed, the ends of the armature plate allow a slight

movement but the plate will feel secure when grasped at the bolt. There

should be no movement to the mounting bracket or housing of the

electromagnetic lock.

For added safety, thread locking compound has been provided for the

armature plate bolt and the four captive electromagnetic lock mounting

screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware to

disengage and fall, causing serious bodily injury and property damage.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO THE

END-USER UPON COMPLETION OF THE INSTALLATION.

8375 Series Troubleshooting Guide

Problem Solution

Insert supplied Allen wrench into mounting bolt holes in the bottom of the lock

housing and turn (See Fig. 1).

- Check power supply. DC power should be slightly over the voltage

specifications outlined on the packaging. EG: for 12VDC operation supply

should be set at 12VDC-13VDC.

- Check connections at power supply, connected releasing devices

and lock terminals.

- Check that voltage selection jumpers are correctly set

- Check that connections from lock circuit board to magnet core have not been

broken or loosened during installation.

Check to see that armature plate is correctly aligned with the electromagnetic lock.

If there is improper alignment, make a 1/4” turn of the armature plate mounting

bolt and check for alignment.

Make sure to follow the armature plate mounting instructions on the template and

box on Page 2 of this install.

This generally indicates that the lock is either operating on AC voltage or there is

some AC voltage present in the DC supply. A properly filtered and regulated DC

power supply is required to achieve optimal operation from the lock.

- Ensure that switching devices are interrupting the DC power and not the AC

power supply voltage

- Ensure rubber washer on armature plate mounting bolt has not been

removed or damaged

- Check that switching device interrupts the positive wire and

not the negative wire (see Fig.3)

- Remove any Diodes or other suppression devices that may be installed

While some heat rise is normal for the 8375, excessive heat generally indicates

that the voltage selection jumpers are incorrectly set.

Cannot remove the lock mounting plate from top of the magnet

for installation.

Lock is installed, but has no holding force at all.

Lock has enough holding force to lightly hold a screwdriver or

set of pliers, but door will not lock.

Lock is operating and locking, but the armature plate is

“humming” against the surface of the lock.

Lock is not releasing immediately upon removal of power.

Lock surface is very warm to the touch.

Specifications

Mechanical:

RCI 8375 Lock Dimensions

(Including 1/8” (3.2mm) mounting bracket):

13/16”D x 1-1/2”W x 6-17/32”L

(21mm x 38mm x 166mm)

Armature Plate: 11/32” x 1-1/4” x 5-1/8”

(8.5mm x 32.0mm x 130.0mm)

Electrical:

Voltage: 12VDC or 24 VDC

(Selected by choosing appropriate voltage selection jumpers)

Current: 0.36A @ 12VDC

0.18A @ 24VDC

Environmental:

Not for use in outdoor environments.

Circuit board operating temperature:

14 to 140° F (-10 to 60° C )

NOTE: Specifications are subject to change without notice.

Voltage Current

12VDC 0.36A

24VDC 0.18A

8375 Current Requirements

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	RCI 8375

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba RCI 8375 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024