Dormakaba RCI 8371 Handleiding

Dormakaba Niet gecategoriseerd RCI 8371

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba RCI 8371 (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

I N S T A L L A T I O N 8371/8372

Surface MiniMag® Electromagnetic Locks

1. Mount the electromagnetic lock to the door frame as outlined

on the installation template included with the product.

NOTE: During installation of the armature plate to the door it is

essential that the armature plate remains movable. The armature

plate must be allowed to pivot on the center-mounting bolt to allow

proper alignment with the magnet surface. If the plate is not aligned

with the magnet surface, the lock may lose holding force or not

lock at all.

The head of the armature mounting bolt ships with a rubber washer

affixed to it. This washer should project slightly beyond the surface

of the armature plate. This is to allow the washer to expand when

power is removed and break the air vacuum between the plate

and the magnet surface. If this washer is removed or trimmed the

lock will appear to have some holding force even when power is

removed.

For added safety, thread locking compound has been provided for

the armature plate bolt and the four captive electromagnetic lock

mounting screws.

WARNING: Improper installation, maintenance, inspection or

usage of the product or any related accessories or parts may

cause the electromagnetic lock, armature plate and associated

hardware to disengage and fall, causing serious bodily injury

and property damage. Rutherford Controls Int’l Inc. and/or

Rutherford Controls Int’l Corp. will not be liable to the installer,

purchaser, end user or anyone else for damage or injury to person

or property due to improper installation, care, storage, handling,

maintenance, inspection, abuse, misuse or act of God or nature

involving this product or any related accessories or parts.

2. Route the power supply wire through door frame and into

magnet housing. Connecting wire should be of sufficient gauge

for the lock being installed and the distance being run. (See table

on page 6.)

WWW.RUTHERFORDCONTROLS.COM • PHONE: 1.800.265.6630 • FAX: 1.800.482.9795 • E-MAIL: SALES@RUTHERFORDCONTROLS.COM

IS8371/72 PCN15010

R10/15GR-2

In or Out... we make it Easy!®

Instructions

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available with

this product, a survey and assessment of the physical area

in which the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be strong

enough to meet or exceed the holding force of the product.

4. The product must be protected from potential damage due

to intruders or tampering.

5. The product should be installed in a location that will not

hinder or create a potential safety hazard to authorized

personnel accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must

make a determination of the optimal mounting method for

this specific application.

7. The components, hardware, installation instructions and

mounting template included with this product are intended

for use on outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories not included with this product must

be used in the following applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that do not have a door frame

• Hollow metal or wood frames where the door stop is

not thick enough to allow the product to be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to be

mounted low enough to meet the magnet surface

Refer to the Product Accessories Guide section of

the Installation Instructions for further information.

Accessories may impact holding force.

11. Installation of this product should be done by an

experienced installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound

be applied to all screws during installation to reduce chance of

screws loosening over extended time.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

8371/ 8372 Electromagnetic Lock Installation Instructions (Continued)

SCS (Security Condition Sensor) with LED

This feature can detect the quality of the locking bond between the

surface of the magnet and the armature plate. The sensitivity of this

feature is such that a foreign object with a thickness of .007” (.18mm)

is sufficient to allow the sensor to detect a problem.

Due to the sensitivity of this feature and the necessity to maintain a

reliable locking bond, these surfaces must be kept free of contaminating

materials. Both the lock surface and the armature plate must be cleaned

periodically with a non-abrasive cleanser. Alignment of armature plate

and magnet is required to ensure proper function of sensor.

DSS (Door Status Sensor)

The DSS option monitors the position of the door upon which the lock

is installed. A SPST reed switch eliminates the need for extra sensors

to be installed on the door for notification of security or access control

systems. The DSS option comes with a magnet pre-installed into the

lock armature plate for signaling the reed switch in the housing when

the door is closed. Care should be taken during the final testing of the

lock to ensure that the DSS option is operating in the desired manner.

Magnet power from

Power Supply

+12/24VDC input

- (Ground)

Jumper

12VDC

Jumper

24VDC

(

preset )

Power Input Requirements

MODE 12VDC 24VDCL

8371 0.52A 0.26A

8372 1.04A 0.52A

2 x BLUE LEADS Normally Open

FOR MODELS WITH OPTIONAL DSS

contacts are rated 0.20A@12VDC

and 0.12A @ 24VDC

shown with Door Open

Wiring : For Unmonitored or DSS Sensor Models

12 1224

G B R

LED

RB G

- VDC C NC NO

G B R

LED

Voltage Jumpers

}

Optional SCS Sensor

SPDT Output contacts rated

for maximum 1.00 Amperes

at 24VDC

Common

Normally Closed

Normally Open

2 x BLUE LEADS Normally Open

Optional DSS contacts rated at

0.20A@12VDC and 0.12A @ 24VDC

Both the SCS and DSS options are shown

with Door Open

Tip: Fully depress orange tab to insert wires

LED

R B G

G B R

LED

12 1224

VDCCNC NO

Voltage Jumpers

}

Optional SCS Sensor

SPDT Output contacts rated

for maximum 1.00 Amperes

at 24VDC

Common

Normally Closed

Normally Open

Optional DSS contacts rated at

0.20A@12VDC and 0.12A @ 24VDC

Both the SCS and DSS options are shown

with Door Open

Tip: Fully depress orange tab to insert wires

2 x BLUE LEADS Normally Open

8371 SCS and 8372 SCS

Side 1

8372 SCS

Side 2

Wiring : For SCS or SCS/DSS Combination Models

Green LED indicates door locked with secure bond.

Red LED indicates door unlocked or poor bond.

UL 294 Performance Ratings:

Access Control Line Security : Level I

Destructive Attack : Level I

Endurance : Level IV

Standby Power : Level I

Power Connections

SWITCH

FILTERED DC SUPPLY

SWITCH

FILTERED DC SUPPLY

INCORRECT

CORRECT

8371/ 8372 Electromagnetic Lock Installation Instructions (Continued)

Fig. 1

Fig. 2 – Lock Mounting

Anti-tamper

screw Wiring cavity

screw

Captive

mounting

bolts

Fig. 3

Anti-tamper screw

(under wiring cavity)

NOTE: All RCI electromagnetic locks must be powered with filtered

and regulated DC power supplies such as the RCI 10 Series UL Listed

power supply. RCI offers a full line of power supplies and switching

devices that are suitable for use with the 8371 and 8372 Surface

MiniMag® locks.

To Ensure Instant Release All switching devices must be wired in between

the DC power source and the positive terminal of the lock as shown.

Switching the negative power supply line will not allow the lock to

release immediately. RCI electromagnetic locks contain MOV’s for

surge suppression and do not require any additional suppression to

be added during installation. The installation of diodes across the lock

input terminals will cause a delay in release.

Anti-Tamper Feature - Two screws prevent insertion of an Allen

wrench into the captive mounting bolt opening on the bottom of the

lock. Fig. 2 shows their location. One screw also secures the wiring

cavity cover. The mounting plate cannot be separated from the lock

without removing these two screws. There is an additional anti-

tamper screw under the wiring cavity cover. See Fig. 3.

Specifications

Mechanical: including 3/16” [5mm] mounting bracket:

8371 Lock Dimensions:

1”D x 1-7/8”W x 9-3/8”L (25 x 48 x 238mm)

8372 Lock Dimensions:

1”D x 1-7/8”W x 18-3/4”L (25x 48 x 476mm)

Armature Plate Dimensions:

1/2”D x 1-1/2”W x 7-1/4”L (13 x 38 x 185mm)

Electrical:

Voltage: 12VDC or 24VDC

Current: Max 0.52A at 12VDC (each lock on 8372 model)

Max 0.26A at 24VDC (each lock on 8372 model)

SCS Output Relay*: SPDT relay. Contacts rated at 1.0A@24VDC

DSS Reed Switch*: Magnetically actuated SPST switch.

Contacts rated for 0.20A @12VDC and 0.12A @ 24VDC

* Effective for either resistive or inductive loads

(power factor 0.6 with inductive loads)≥

Environmental:

Not for use in outdoor environments.

Circuit board operating temperature: 32 to 120 F (0 to 49˚ ˚ ˚ ˚C)

NOTE: Specifications subject to change without notice.

Inspection and Maintenance

This product and all related accessories or parts must be inspected

and maintained on a . Contacting surfaces of the quarterly basis

electromagnetic lock and armature plate must be kept free of

contaminating materials. Surfaces must be cleaned periodically

with a non-abrasive cleaner.

All mounting fasteners must be inspected on a quarterly basis.

When properly installed, the ends of the armature plate allow a

slight movement but the plate will feel secure when grasped at

the bolt. There should be no movement to the mounting bracket

or housing of the electromagnetic lock.

For added safety, thread locking compound has been provided for

the armature plate bolt and the four captive electromagnetic lock

mounting screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware

to disengage and fall, causing serious bodily injury and property

damage.

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	RCI 8371

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba RCI 8371 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024