Dormakaba RCI 8360 Handleiding

Dormakaba Niet gecategoriseerd RCI 8360

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba RCI 8360 (3 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/3

INSTALLATION

RCI 8360

MiniMag® MORTISE ELECTROMAGNETIC LOCK

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

1. Hold lock against frame at desired level. Mark the lock’s horizontal

centerline on the frame and transfer that mark to the door.

2. Determine the vertical centerline of the door thickness and mark

this on both the door and the frame.

3. Using these centerline references, cut out the lock mortise in

the frame as illustrated.

4. Temporarily fasten the two mounting tabs under the lock

flanges. Insert the lock assembly into the frame cavity until the

tabs are resting on top. Mark the location of the tab mounting

holes.

5. Drill and countersink these four holes to accept the 3/16” screws

provided.

6. Remove tabs from lock. Mount the tabs inside the frame.

7. Set voltage dipswitches as follows:

12VDC operation = 1 and 2 are On / 3 is Off

24VDC operation = 1 and 2 are Off / 3 is On (factory setting)

Connect the positive (+) power lead to the red and the negative

(-) lead to the black wire.

Connecting wire should be of sufficient gauge for the lock being

installed and the distance being run. See table on page 3 for

current draw specifications.

8. RLS (Remote Lock Status)

This feature can detect the quality of the locking bond between

the surface of the magnet and the armature plate. The

sensitivity of this feature is such that a foreign object with a

thickness of .007” (.18mm) is sufficient to allow the sensor to

detect a problem.

Due to the sensitivity of this feature and the necessity to

maintain a reliable locking surface, these surfaces must be kept

free of contaminating materials. Both the lock surface and the

armature plate must be cleaned periodically with a non-abrasive

cleanser. Proper alignment of the armature plate and magnet is

required to ensure proper function of sensor.

The 3 RLS lead wires at the lock corner are: Red = Normally

Closed, Black = Common, Green = Normally Open with the

door open / unlocked.

IS8360 PCN18041

R09-19GR-1

Instructions

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available with this

product, a survey and assessment of the physical area in which

the product will be installed must be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be strong

enough to meet or exceed the holding force of the product.

4. The product must be protected from potential damage due to

intruders or tampering.

5. The product should be installed in a location that will not hinder

or create a potential safety hazard to authorized personnel

accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must make

a determination of the optimal mounting method for this specific

application.

7. Do not install this product on the exterior of buildings.

8. Do not use as a doorstop. This will void warranty.

9. Installation of this product should be done by an experienced

installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound be

applied to all screws during installation to reduce chance of screws

loosening over extended time.

WARNING: Improper installation, maintenance, inspection or

usage of the product or any related accessories or parts may

cause the electromagnetic lock, armature plate and associated

hardware to disengage and fall, causing serious bodily injury

and property damage. dormakaba Canada Inc .and/or dormakaba

USA Inc. will not be liable to the installer, purchaser, end user

or anyone else for damage or injury to person or property due

to improper installation, care, storage, handling, maintenance,

inspection, abuse, misuse or act of God or nature involving this

product or any related accessories or parts.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

Instructions Cont’d

IMPORTANT: The RLS contacts are rated at a maximum of

0.20 Amps. Greater current will cause damage to the

sensor and will void warranty.

9. Secure lock on tabs in mortise cavity, carefully applying thread

locking compound to the hardware provided.

10. Using centerline references on the door and illustration provided,

drill the four “U” clamp mounting holes and cut out the armature

mortise.

11. Position the “U” clamp inside door as shown. Insert the two pan

head sex nuts from the outside of the door and through the “U”

clamp. Insert the two button head hex bolts from the inside of the

door and secure into the sex nuts.

12. Position bolt with rubber head through armature plate. Add 3

washers (steel - rubber - steel) onto threads. Carefully apply

thread-locking compound to exposed thread and mount onto the

“U” clamp.

NOTE: Do not over tighten. The armature plate must be allowed

to pivot on the mounting bolt to allow proper alignment with the

magnet surface. If the plate is not aligned with the magnet surface,

the lock may lose holding force or not lock at all.

The head of the armature mounting bolt ships with a rubber washer

affixed to it. This washer should project slightly beyond the surface

of the armature plate. This is to allow the washer to expand when

power is removed and break the air vacuum between the plate

and the magnet surface. If this washer is removed or trimmed, the

lock will appear to have some holding force even when power is

removed.

13. With a release device already installed, energize circuit and close

door gently. If magnet does not secure, verify that armature plate

is making contact with face of magnetic block. If necessary, install

additional steel washers behind armature plate to move armature

plate closer to block face and retest.

Inspection and Maintenance

This product and all related accessories or parts must be inspected

and maintained on a Contacting surfaces of quarterly basis.

the electromagnetic lock and armature plate must be kept free of

contaminating materials. Surfaces must be cleaned periodically with a

non-abrasive cleaner.

All mounting fasteners must be inspected on a . When quarterly basis

properly installed, the ends of the armature plate allow a slight movement

but the plate will feel secure when grasped at the bolt. There should be

no movement to the mounting bracket or housing of the electromagnetic

lock.

For added safety, thread locking compound has been provided for the

armature plate bolt and the four electromagnetic lock mounting screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware

to disengage and fall, causing serious bodily injury and property

damage.

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO THE

END-USER UPON COMPLETION OF THE INSTALLATION.

NOTE: All RCI brand electromagnetic locks must be powered with filtered and regulated DC power supplies. dormakaba offers a full line of power

supplies and switching devices that are suitable for use with the 8300 Series locks.

www.dormakaba.us • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com

* Interior and exterior drill sizes are different.

NOTE: Specifications are subject to change without notice.

Voltage Current

12VDC 0.50A

24VDC 0.25A

Frame Door

A B E F G H I (Interior) * J (Exterior) *

Inches

Fractional 1-9/16 9 1-9/16 7-5/16 1-7/32 9/16 11/32 1/2

Inches

Decimal 1.57 9.0 1.56 7.32 1.22 0.55 0.34 0.50

Metric

(mm) 40.0 229.0 39.0 186.0 31.0 14.0 8.5 13.0

8360

Electromagnetic

Lock

Mounting

Tab

Frame

Extrusion

Extertior

Side

Interior

Side

Shock absorbin g

rubber washe r

Metal

washers

cut

out

cut

out

J *

I *

"U" Clamp

Do not over tighten

preventing movement.

Exterior side

door drilling

Interior side

door drilling

Frame

Sliding Door

Frame

Sliding Door

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	RCI 8360

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba RCI 8360 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024