Dormakaba RCI 8 Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba RCI 8 (1 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 31 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/1
I N S T A L L A T I O N
Read and conform to each of the Pre-Installation instructions
supplied with Rutherford Controls electromagnetic lock.
This product must be used only with a Rutherford Controls
electromagnetic lock.
Failure to conform to these requirements is a misuse of the
product and could result in serious bodily injury or property
damage.
1. Open wiring cavity in front of lock. For remote indication
requiring a contact when door is closed, connect the closed
green lead (NC) black lead (COM). and the
For remote indication requiring a contact when door is open
closed, connect the and the red lead (NO) black lead (COM).
2. Install the DSS Reed Switch into the housing. Take care to
slide the Reed Switch to the bottom of the housing to ensure
reliable operation.
NOTE: When connecting to the reed switch leads, the connections
should be soldered or correct size â„¢ must Marrettesâ„¢/Wire Nuts
be used. The ‘DSS’ option reed switch contacts are rated at 0.20A
@ 12VDC and 0.12A @ 24VDC. Do not exceed this rating.
3. Replace standard armature plate with longer DSS armature
plate. Apply thread locking compound to bolt before
re-engaging into sexnut.
NOTE: During installation of the armature plate to the door it is
essential that the armature plate remains movable. The armature
plate must be allowed to pivot on the center-mounting bolt to
allow proper alignment with the magnet surface. If the plate is not
aligned with the magnet surface, the lock may lose holding force
or not lock at all.
The head of the armature mounting bolt ships with a rubber
washer affixed to it. This washer should project slightly beyond
the surface of the armature plate. This is to allow the washer
to expand when power is removed and break the air vacuum
between the plate and the magnet surface. If this washer is
removed or trimmed the lock will appear to have some holding
force even when power is removed.
WARNING: Improper installation, maintenance, inspection
or usage of this or any related product may cause the
electromagnetic lock, armature plate and associated hardware
to disengage and fall, causing serious bodily injury and
property damage. dormakaba Canada Inc. will not be liable to
the installer, purchaser, end user or anyone else for damage or
injury to person or property due to improper installation, care,
storage, handling, maintenance, inspection, abuse, misuse or
act of God or nature involving this or any related product.
8 series
ISDSS PCN18003
R03-18GR-1
Maintenance
This product and all related accessories or parts must be inspected and maintained on a . Contacting surfaces of the electromagnetic quarterly basis
lock and armature plate must be kept free of contaminating materials. Surfaces should be cleaned periodically with a non-abrasive cleaner.
All mounting fasteners must be inspected on a . When properly installed the ends of the armature plate allow a slight movement, but quarterly basis
the plate will feel secure when grasped at the bolt. There should be no movement to the mounting bracket or housing of the electromagnetic lock.
Instructions
(Wiring directly to the ‘DSS’ Option Reed Switch)
DSS RETROFIT
ELECTROMAGNETIC LOCK ACCESSORY
DSS Reed Switch
Position stripe close
to wiring cavity
Inside Details
of Endcap
© 2018 dormakaba Canada Inc.
www.rutherfordcontrols.com • Phone: 1.800.265.6630 • Fax: 1.800.482.9795 • E-mail: sales_RCI@dormakaba.com


Product specificaties

Merk: Dormakaba
Categorie: Niet gecategoriseerd
Model: RCI 8

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba RCI 8 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Dormakaba

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd