Dormakaba Keyscan CIM Handleiding


Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba Keyscan CIM (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 175 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Pagina 1/2
Keyscan CIM
Communications Interlink Module
Communication that
meets the sophisticated
demands of today’s
access control systems
The Keyscan CIM is a communication control module designed
to use a CAN Bus communication network. It provides
optimized server to access control unit (ACU) communication
as well as gives users an ACU to ACU network providing
inter-panel communication for global communication
functions including anti-passback, global input/output and
global time zones.
The CIM includes an impressive host of new features including
ground loop protection, enhanced diagnostics, improved
speed and unprecedented reliability.
Standardized Cabling
Establishes communication links with CAN Bus communication
protocol using standard CAT5 cabling.
Ground Loop Tolerance
Maximizes electrical isolation to earth ground providing
tolerance against ground loops.
Fault Tolerance
If one CIM goes down, it won’t take the loop down with it.
CAN Bus protocol offers non-interrupted communication of
remaining devices on the network.
Communication Speeds
Provides optimized communication speeds, up to 115K BPS.
Enhanced Diagnostics
Provides many diagnostics for quick and easy troubleshooting.
Auto Bit Rate Configuration
Designed to automatically match bit rate speed with
control unit configuration.
Network Adaptation
Supports Keyscan’s plug-on TCP/IP network adapter
NETCOM2P/6P. (pictured above)
Ribbon Cable
Uses a simplified ribbon cable connection to control unit for
fast installation.
Global Communication
Access Control Units with direct connectivity with the CAN
Bus network now provide ACU to ACU communication without
server dependence. This permits a host of new features and
capabilities.
Specifications
dormakaba Canada Inc.
901 Burns St., E.,
Whitby, Ontario
Canada L1N 0E6
1 888 539 7226
www.dormakaba.us KKT2051 2018-07
© dormakaba Canada Inc. (2018). Information on this sheet is intended for general use only. dormakaba Canada reserves the right to alter designs and
specifications without notice or obligation. Printed in Canada.
Operating Voltage 12 VDC
Current Draw (CIM only) 150 mA
CIM with NETCOM2P/6P 290 mA
Dimensions 4 5/8” x 3” (11.7 cm x 7.6 cm)
Operating Environment 32 F - 140 F (0 C - 60 C)
Topology Linear
Network support Standard, Encrypted, Reverse IP
CAN Bus CAN Bus 1 - Server to ACU communication
CAN Bus 2 - ACU to ACU global communication
Firmware Minimum EPROM versions 7.40/8.20
Software
Keyscan Aurora (all)
System 7.0.16 or higher
Vantage 8.1.15 or higher
Network communication via NETCOM2P/6P
NETCOM2P or NETCOM 6P (encrypted) plug directly into the CIM module to establish network
communication. They must first be programmed. The CIM module with the network connection is referred to as CIM 0.
Refer to the NETCOM2P or NETCOM 6P/CIM programming guides for full instructions.
PC / ACU Bit Rate
9600 or 19,200
57,500
115,200
CAN Bus 1 & 2 CAT 5 Distance*
3280 ft (1000m)
984.25 ft (300m)
262.46 ft (80m)
RS-232 Serial Distance
49.2 ft (15m)
26.2 ft (8m)
9.84 ft (3 m)
* Refers to the maximum recommended cabling distance between the 1st and last CIMs on any communication loop.


Product specificaties

Merk: Dormakaba
Categorie: Niet gecategoriseerd
Model: Keyscan CIM

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba Keyscan CIM stel dan hieronder een vraag en andere gebruikers zullen je antwoorden




Handleiding Niet gecategoriseerd Dormakaba

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd