Dormakaba ICU1200 Handleiding

Dormakaba Niet gecategoriseerd ICU1200

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba ICU1200 (8 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 38 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/8

ICU1200

Manual bi-directional swing door

with bi-fold function

Installation and Maintenance Manual

DL3191-010 – 05-2022

| | EN

2 ICU300 / ICU300T 05-2022DL3191-010

ICU1200 Manual Bi-directional Swing Door

with Bi-fold Function Installation and Maintenance Manual

ICU1200 series Manual Doors

Installation and Maintenance

1 Pre-install Preparation ......................................................... 3

1.1 Tools Required .............................................................. 3

1.2 Unpacking ..................................................................... 3

1.3 Canopy Assembly ......................................................... 3

1.4 Wing Glazing ................................................................. 4

2 Enclosure Assembly and Installation ................................... 4

3 Pivot Bearing Installation ..................................................... 5

4 Bent Glass installation ......................................................... 5

5 Completing Installation ........................................................ 6

5.1 Shaft Installation ........................................................... 6

5.2 Wing Installation ............................................................ 6

5.3 Floor Strikes .................................................................. 6

6 Cover Installation and Calking ............................................. 7

3ICU1200 05-2022DL3191-010

ICU1200 Manual Bi-directional Swing Door

with Bi-fold Function Installation and Maintenance Manual

1 Pre-install Preparation

1.1 Tools Required

The following tools are needed for the complete installation. Those tools noted with ‘driver’ are

beneficial to have with a power driver (cordless drill with torque clutch is the best).

 9/16” open end wrench or socket wrench

 7/16” open end wrench and socket driver

 5/16” socket driver (power required)

 1/8” hex key and driver

 5/32” hex key and driver

 1/16” hex key (for lock cylinder change)

 Razor knife or box cutter

 Small soft face mallet

 Hammer drill or other tools for drilling floor

 Ø1-3/8” masonry drill (depending on floor)

 Tools for floor anchors

 Glass cups for curved glass

The following consumables will be needed for installation.

 Por-Rok or similar flowable quick setting non-shrink anchoring cement

 ½” X 1/8” single side adhesive glazing foam tape

 Spray glue (optional)

 Tapcon or other appropriate floor anchors (1/4” max. diameter)

 Aluminum or plastic shims (as needed)

 Silicone or other non-hardening exterior grade calk

 Backer rod (as needed)

1.2 Unpacking

Whenever boxes or crates are unpacked, be careful not to damage or lose components. Do not cut

through tape where it may scratch the items inside the carton.

Depending on the size and shipping requirements, your door may have the canopy packed in two

halves. The speed control will be attached to the speed control soffit and packed separately from the

rest of the canopy in the crate with the shaft (with hangers attached). This crate will also contain the

bases, covers, small parts kit (including pivot bearing and speed control oil)

1.3 Canopy Assembly

If the canopy was shipped in two halves, they should be re-assembled before beginning the rest of

the installation process. If your canopy arrived as one piece, this assembly process will not be

needed. The assembly of the canopy can be completed on-site or prepped before installation begins.

This assembly process should be completed with the canopy (fascia edge) resting on a flat surface or

the soffit resting on a pair of long parallel saw horses.

1. Position and attach the speed control brackets using ¼-20 X 5/8” low head socket cap screws

(LHSCS) and ¼” lock washers as shown.

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	ICU1200

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba ICU1200 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024