Dormakaba ES96 Handleiding

Dormakaba Niet gecategoriseerd ES96

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba ES96 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 29 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

ISES96F

08281280

PCN2007

R09-20GR

I N S TA L L AT I O N S

E S 9 6 F

Electric Strikes

DORMA DRIVE, DRAWER AC, REAMSTOWN, PA 17567 PHONE: (800) 523-8483 (717) 336-3881 FAX: (717) 336-2106

EMAIL: archdw.us@dormakaba.com dormakaba.us WEBSITE:

Standard Parts:

Insert

Deadbolt Keeper

Deadbolt Plug

Deadlatch Ramp (Auxiliary Bolt Bracket)

Keeper Sliding Shims: 1/16" (1.5mm) and 1/8" (3.0mm)

A Centerline Latch Faceplate and an Offset Latch Faceplate are

provided. Both are: 4-7/8" x 1-1/4" (123.8mm x 31.8mm)

Trim Plate

12VDC or 12 to 24VAC Cable Connector

24VDC Cable Connector

Anti-Tamper Security Screws (2x 12-24) and Bit

Mounting Tab Kit (2x tabs, 4x shims and 5x 12-24 screws)

Inductive Kickback Suppressor - MOV

Red Black

24VDC

Terminal

12VDC

12-24VAC

Terminal

Latch

Monitor

Optional LM

Wiring the ES96F Series Electric Strike

Wiring Instructions

Use the appropriate wire harness supplied.

12V for 12VDC & 12-24VAC*

24V for 24VDC only

Attach the red wire to (+) positive of the power supply.

Attach the black wire to the (–) negative of the power supply.

If using AC power, polarity is not observed.

To meet BHMA A156.31, install the MOV provided across the positive

and negative wires or terminals of the harness. The MOV is not polarity

sensitive.

NOTE: If a suppression diode is required for access control,

observe proper polarity.

Latch Monitor Wires

Black = Common (C)

Blue = Normally Closed (NC)

Orange = Normally Open (NO)

The ES96F fail secure locking mechanism shall only be installed where allowed by the local authority having jurisdiction and shall not

impair the operation of the panic hardware or intended operation of the emergency exit.

Model ES96F must be connected to a compatible UL Listed Burglary or Access Control Power Supply.

Accessories:

96LM Latch Monitor : 08116660

UL 294 Performance Ratings:

Access Control Line Security : Level I

Destructive Attack : Level I

Endurance : Level IV

Standby Power : Level I

Trim Plate: This can be used in

case the frame cutout is bigger

than required.

Bend tabs to

grip frame

Deadbolt Plug: If the lock set

doesn’t have a deadbolt, then

replace deadbolt keeper with

deadbolt plug.

NOTE: Deadlatch Ramp also acts

as a Keeper stop, so don’t forget to

insert it for centerline cylindrical lock

applications.

Deadbolt

Plug

Cylindrical

Horizontal Adjustment: If there is play

in the door when closed; the keeper

shims may be used to minimize play.

Keeper

Sliding Shim

1. Place the folded template square to the frame. Horizontally align

holes marked on the template with the mounting holes in frame.

2. Peel adhesive backing and paste the folded template square to the

frame.

3. Carefully cut the frame inside the un-shaded area marked on the

template. Install strike per installation instructions ISF2

For Cutting ANSI Prep Frames

NOTE: Specications subject to change without notice.

* Dimension F is measured from face of mounting tab to face of

frame.

** Dimension X on the drawing is determined by the vertical

centerline of the door. If the latch incorporates a deadlocking pin

additional steps will be necessary to ensure proper operation of the

deadlocking pin. Measure the thickness of the deadlocking pin and

add this thickness to Dimension X to relocate the vertical centerline an

appropriate distance on the frame.

MEASUREMENT

FRACTIONAL

INCHES

DECIMAL

INCHES

METRIC

A 1-1/4” 1.250 31.75

B 4-7/8” 4.875 123.83

C 3-3/8” 3.375 85.73

DF + 1-7/16” F + 1.438 F + 36.51

E 3/8” 0.375 9.53

F 3/16”* 0.188* 4.76*

G 1-11/16” 1.688 42.86

X Vertical Centre Line of Door

Lock and Mounting Face Plate**

K 4-1/8” 4.125 104.78

M 12-24 N/A N/A

Z 3-5/16” 3.315 84.14

Frame Prep Dimensions

Special Features

1. Mark the horizontal Lock Body Centerline on the door.

Close the door and transfer the Lock Body Centerline to the

frame.

If the door isn’t ush to the frame in the closed position, mark

the depth of the closed door on the frame. Measure half of the

door thickness back toward the door stop and mark the vertical

Door Centerline on the frame.

2. Horizontally align the proper Template Lock Centerline with

the Lock Body Centerline marked on the frame. Peel adhesive

backing and paste the folded template square to the frame.

If the door isn’t ush to the frame when closed, tear the tem-

plate at the fold line. Align the faceplate portion vertically with

the Door Centerline and match the template Lock Centerline

with the Lock Body Centerline marked on the frame.

Carefully paste the front portion of the template on face of

frame to align with the faceplate portion.

3. Carefully cut the frame inside the un-shaded area marked on

the template.

Follow Mounting Tab Installation Instructions.

For Cutting Frames without ANSI Prep

Frame

Self-Adhesive

Mounting Shim

(4 incl.)

Mounting bTa

(2 incl.)

12-24 Machine

Screws (2 per tab)

a) Fasten the mounting tabs to the faceplate of the strike, selecting the

appropriate shims for the installation.

b) Using the assembled strike and tabs as a template, place against the

frame and mark the mounting hole locations. Remove and drill a 3/16”

hole in frame for each mounting tab and countersink the frame.

c) Remove the tabs from the faceplate and install in the frame using the

12-24 x 3/8” machine screws supplied. Tabs are plated and drilled and

tapped for this purpose.

d) Install strike per page 4 mounting instructions.

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	ES96

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba ES96 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024