Dormakaba EMLTP Handleiding

Dormakaba Niet gecategoriseerd EMLTP

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba EMLTP (6 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 22 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/6

INSTALLATION

EML310TP, EML320TP

Electromagnetic Locks

DORMA DRIVE, DRAWER AC, REAMSTOWN, PA 17567 PHONE: (800) 523-8483 (717) 336-3881 FAX: (717) 336-2106

EMAIL: archdw.us@dormakaba.com WEBSITE: dormakaba.us

Pre-Installation Instructions

1. This product must be installed according to all applicable

building and life safety codes.

2. Due to the variety of mounting configurations available

with this product, a survey and assessment of the

physical area in which the product will be installed must

be performed.

3. The door frame must be inspected and deemed structurally

sound prior to installation of the electromagnetic lock. The

structural integrity of the mounting surfaces must be

strong enough to meet or exceed the holding force of the

product.

4. The product must be protected from potential damage

due to intruders or tampering.

5. The product should be installed in a location that will not

hinder or create a potential safety hazard to authorized

personnel accessing the protected area.

6. Because electromagnetic locks are used in a variety of

applications and different door frame configurations, an

experienced installer with knowledge of this product must

make a determination of the optimal mounting method for

this specific application.

7. The components, hardware, installation instructions and

mounting template included with this product are intended

for use on outswinging doors.

8. Do not install this product on the exterior of buildings.

9. Do not use as a doorstop. This will void warranty.

10. Separate accessories must be used in the following

applications:

• Inswinging doors

• Narrow head jamb situations or center-hung doors

• Wherever there is insufficient space on the door

frame header to mount the lock

• Glass or Herculite doors that don’t have a door frame

• Hollow metal or wood frames where the door

stop is not thick enough to allow the product to

be installed

• Wherever an obstruction in the door prevents

installation of the armature plate at a proper height

• Doors that do not permit the armature plate to be

mounted low enough to meet the magnet surface

Refer to the page 5 & 6 Product Accessories Guide for

further information. Accessories may impact holding

force.

11. Installation of this product should be done by an

experienced installer with knowledge of this product.

NOTE: It is highly recommended that thread locking compound

be applied to all screws during installation to reduce chance of

screws loosening over extended time.

ISEML310TP

08281550

PCN18040

R08-19GR

1. Mount the electromagnetic lock to the door frame as outlined

on the installation template included with the product.

NOTE: During installation of the armature plate to the door it

is essential that the armature plate remains movable. The

armature plate must be allowed to pivot on the center-mounting

bolt to allow proper alignment with the magnet surface. If the

plate is not aligned with the magnet surface, the lock may lose

holding force or not lock at all.

The head of the armature mounting bolt ships with a rubber

washer affixed to it. This washer should project slightly beyond

the surface of the armature plate. This is to allow the washer

to expand when power is removed and break the air vacuum

between the plate and the magnet surface. If this washer is

removed or trimmed the lock will appear to have some holding

force even when power is removed.

For added safety, thread locking compound has been provided

for the armature plate bolt and the four captive electromagnetic

lock mounting screws.

WARNING: Improper installation, maintenance, inspection

or usage of the product or any related accessories or parts

may cause the electromagnetic lock, armature plate and

associated hardware to disengage and fall, causing serious

bodily injury and property damage. dormakaba Canada Inc.

and/or dormakaba USA Inc. will not be liable to the installer,

purchaser, end user or anyone else for damage or injury

to person or property due to improper installation, care,

storage, handling, maintenance, inspection, abuse, misuse

or act of God or nature involving this product or any related

accessories or parts.

2. Route the power supply connecting wire through the door

frame and into the wire access hole in the top of the magnet

housing. Connecting wire should be of sufficient gauge for

the lock being installed and the distance being run.

Installation Instructions

PLEASE DELIVER ALL INSTALLATION INSTRUCTIONS TO

THE END-USER UPON COMPLETION OF THE INSTALLATION.

3. Set the DC voltage jumpers on JP1 as follows.

For 12V operation two jumpers are used; One on the

two upper pins and the other on the two lower ones.

For 24V operation only one jumper is used to connect

the two center pins (factory setting)

Connect the positive (+) lead from the power supply to

TB1-1. Connect the negative (-) lead from the power

supply to TB1-2. For wiring installations, refer to

figure 1.

4. Delayed Relock Feature - The delayed relock feature can

be used to momentarily release the lock and keep it

unlocked for a time period from 0 to 90 seconds. The

time delay for this feature can be adjusted by carefully

turning the potentiometer in a counterclockwise

direction to increase delay time. Factory setting is zero

seconds (fully clockwise).

NOTE: On the EML320TP double-door model turn both

potentiometers counterclockwise to increase the relock

delay.

JP1

JP2

TB1

Alarm Time Setting

Voltage Selection

Light Emitting

Diode (LED)

Time Delay Setting (0-90 secs)

CCW increases time delay

N.C

N.O.

Common

N.C

N.O.

Common

-Common (Ground)

+12/24VDC input

Bond Alert Sensor*

Output contacts SPDT rated at

2.0A @ 30VDC max

Magnet power from

Power Supply

Alarm Status*

Output contacts SPDT rated

2.0A @ 30VDC max.

Power Input Requirements

MODEL 12VDC 24VDC

EML310TP 0.59A 0.29A

EML320TP 1.18A 0.58A

*Shown with Door Open/unlocked

Fig. 1 – Wiring Schematic

Electromagnetic locks must conform to local fire codes, National Building Codes and Life Safety Codes. See your

Local Authority Having Jurisdiction for specific code requirements.

Alarm

Alarm Status Remote Indication - When the door is closed

and an illegal armature plate is detected, the common

contact (TB1-6) and the normally open contact (TB1-7)

are activated for the preset period of time. The alarm

status relay contacts are rated at 30VDC @ 2.0 amps

maximum.

Alarm Time Setting

- Refer to figure 1 (JP2). Note 15 or

30 seconds requires one jumper; 60 seconds requires

no jumper and indefinitely requires two jumpers. Unused

jumpers can be stored on a single pin.

15 Seconds 30 Seconds 60 Seconds Indefinitely

Bond Alert (BA)

Magnet Locked - When the magnet is locked, the common

contact (TB1-3) and the normally open contact (TB1-4)

are closed. The normally closed contact (TB1-5) would be

open.

Magnet Unlocked - When the magnet is unlocked, the

common contact (TB1-3) and the normally closed contact

(TB1-5) are closed. The BA relay contacts are rated 30VDC

@ 2.0 amps maximum.

This feature can detect the quality of the locking bond

between the surface of the magnet and the armature plate.

The sensitivity of this feature is such that a foreign object

with a thickness of .007” (.18mm) is sufficient to allow the

sensor to detect a problem.

Due to the sensitivity of this feature and the necessity to

maintain a reliable locking bond, these surfaces must be

kept free of contaminating materials. Both the lock surface

and the armature plate must be cleaned periodically with

a non-abrasive cleanser. Alignment of armature plate and

magnet is required to ensure proper function of sensor.

LED Local Indication (Light Emitting Diode)

Red LED on solid – Maglock is unlocked

Green LED on solid – Maglock is locked.

Red LED blinking quickly – Illegal armature plate used;

alarm will be activated.

Each individually encoded armature plate is registered to

match it’s own electromagnetic lock.

Anti-Tamper Feature - Two screws prevent insertion of an

Allen wrench into the captive mounting screw opening on

the bottom of the lock. Fig. 3 shows their location. One

screw also secures the wiring cavity cover. The mounting

plate cannot be separated from the lock without removing

these two screws.

Inspection and Maintenance

This product and all related accessories or parts must be

inspected and maintained on a . Contacting quarterly basis

surfaces of the electromagnetic lock and armature plate

must be kept free of contaminating materials. Surfaces

must be cleaned periodically with a non-abrasive cleaner.

All mounting fasteners must be inspected on a quarterly

basis. When properly installed, the ends of the armature

plate allow a slight movement but the plate will feel secure

when grasped at the bolt. There should be no movement

to the mounting bracket or housing of the electromagnetic

lock.

For added safety, thread locking compound has been

provided for the armature plate bolt and the four captive

electromagnetic lock mounting screws.

WARNING: Improper installation, maintenance, inspection or usage

of the product or any related accessories or parts may cause the

electromagnetic lock, armature plate and associated hardware to

disengage and fall, causing serious bodily injury and property damage.

PLEASE DELIVER ALL INSTALLATION

INSTRUCTIONS TO THE END-USER UPON

COMPLETION OF THE INSTALLATION.

For product support, parts and

ordering information contact:

dormakaba USA Inc.

Dorma Drive, Drawer AC

Reamstown, PA 17567 USA

Phone: (717) 336-3881

Fax: (717) 336-2106

Toll Free: (800) 523-8483

Email:archdw.us@dormakaba.com

To Ensure Instant Release All switching devices must be

wired in between the DC power source and the positive

terminal of the lock in Fig 2.

Switching the negative power supply line will not allow

the lock to release immediately. DORMA electromagnetic

locks contain MOV’s for surge suppression and do not

require any additional suppression to be added during

installation. The installation of diodes across the lock input

terminals will cause a delay in release.

Fig. 2 – Power Connections

SWITCH

INCORRECT

CORRECT

SWITCH

FILTERED DC SUPPLY

Fig. 3 – Lock Mounting

Anti-tamper

screw Anti-tamper

and wiring

cavity screw

Captive

mounting

screw

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	EMLTP

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba EMLTP stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024