Dormakaba DE9000 Handleiding

Dormakaba Niet gecategoriseerd DE9000

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba DE9000 (11 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 80 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/11
DE9300 DE9500 DE9100
INSTALLATION INSTRUCTIONS
RIM MORTISE CONCEALED VERTICAL ROD
WIRE PIG TAIL
End Cap
DE5300 DE5500 DE5100
SIZE A: (DE9000 Series)
Will fit 48" (1219 mm) door opening without cutting.
Can be cut to fit a 40 1/2" (1029 mm) minimum door opening.
SIZE B: (DE9000 Series)
Will fit 36" (914 mm) door opening without cutting.
Can be cut to fit a 34 1/2" (876 mm) minimum door opening.
End Cap Bracket
Filler (DE9000/DE5000)
REQUIRES DORMA ES-100 or AD100 POWER SUPPLY.
Easily accessible slide in and out electronics.
Meets UL, ANSI/BHMA & CBC requirements.
Note: Refer to Individual Series Installation Instructions for templating and installation of device; @ www.dorma-usa.com
These are additional instructions for installation and operation of the "Delayed Egress" unit.
NOTE: "Always disconnect power prior to making
any connections or service!"
Observe proper static discharge grounding procedures
when installing or servicing the Delayed Egress device.
SIZE AA: (DE5000 Series w/ #443 strike)
Will fit 48" (1219 mm) door opening without cutting.
Can be cut to fit a 38 3/4" (984 mm) minimum door opening.
SIZE BB: (DE5000 Series w/ #443 strike)
Will fit 36" (914 mm) door opening without cutting.
Can be cut to fit a 31 3/4" (806 mm) minimum door opening.
85 Decibel Alarm - Standard
LED Status Indicator - Standard
Nuisance Alarm - Standard
Key Switch Control - Standard
Remote Authorized Egress - Standard
Remote Re-Arm - Standard
Remote Bypass - Standard
Door Position Input - Standard, DIP Switch Setting
Auto Reset or Manual Reset, DIP Switch Setting
Auto - Stanadard (Manual - in CA)
Additional Form "C" Relays For Optional Horn etc.
(Rated 1 amp @ 30 vdc)
Touchbar/Rail
Assembly
(Delayed Egress)
Connecting Plugs
NOTE:
If cutting to length is required
carefully remove filler and
electronics for cutting. Use all
grounding precautions.
Assembly
1
Mortise Cylinder
(factory supplied)
Pt. No. 90B10SC118
Specifications
DE5000 & DE9000 SERIES
DELAYED EGRESS EXIT DEVICE
IDE - 12 8/09
1135-88 95011817
2
2
2
22
Cylinder Specification
5/16" - 11/32"
Standard 1 1/8" mortise cylinder, randomly
keyed supplied by factory. Spacer required
for longer cylinder such as when using an
IC core.
1 1/8" Standard
21/32"
DIP Switch Setting
DE Filler
Cylinder
90B10SC118
Actuator-DE
95055525
Cylinder Nut
4000-167-501
Underside of Filler
To Change Cylinder: Carefully remove filler from rail. Unscrew cylinder
nut, remove actuator and replace cylinder. Spacer required for cylinders
over 1 1/8". Insert cylinder as shown, re-install actuator & secure with
cylinder nut. Do not over tighten. Re-install filler in rail and reconnect the
small pigtail connectors. Use caution not to pinch or bind wires.
Note: DIP If switch settings required to be changed, do it now prior to
re-installing filler in rail. (See Section below.)
Underside of Filler
ON
OFF
1 2 3 4
(1) DPS: (OFF) ACTIVE (ON) NOT ACTIVE
(2) POWER UP STATE: (OFF) LOCKED (ON) UN-LOCKED
(3) NUISANCE TIME: (OFF) 1 SEC. (ON) 3 SEC.
(4) AUTHORIZED EGRESS TIME: (OFF) 10 SEC. (ON) 20 SEC.
DIP switch settings should be completed at time of initial installation;
check local building code. Factory settings are as follows:
1 - ON - NOT ACTIVE
2 - OFF - LOCKED
3 - ON - 3 SECONDS
4 - OFF - 10 SECONDS
(6310D)
CAM
Basic wire connection
Basic wire connection
Basic wire connection
Basic wire connectionBasic wire connection
1
1
1
112
2
2
223
3
3
334
4
4
445
5
5
55
6
6
6
667
7
7
778
8
8
889
9
9
9910
10
10
1010
11
11
11
1111 12
12
12
1212
DORMA ES100
Minimum 18 AWG
wire recommended for
24VDC inputs (red &
black) leads.
DORMA ES105
(Power Transfer)
"Recommended"
* For 24VDC inputs only (red & black wires).
Note: Wire run is from supply to device
and back to the supply.
WIRE 18AWG 16AWG 14AWG 12AWG
FEET 25 50 75 100
Maximum Wire Length From Power Supply To
Device & Back To Supply In Feet x Wire Gage/Size
3
Monitoring
Outputs
Control Inputs
CAUTION:
TURN OFF 120VAC POWER PRIOR TO MAKING ANY CONNECTIONS TO TERMINALS
WHITE
BLACK
GREEN
(NEUTRAL)
(HOT)
(GROUND)
120 VAC
POWER LINE
(1.0 AMP MAX.)
From UPS
Power Source
Green Ground
Screw Located
On Chassis
TO
N.C. CONTACTS
IN FIRE ALARM
CONTROL PANEL.
DORMA MODEL ES100
24 VOLT DC POWER SUPPLY
FUSE PUSH
TO RESET
CIRCUIT
BREAKER
3.0 AMP
24VDC
3/4 AMP
120VAC
REPLACE WITH 3AG 3/4 AMP
SLO-BLOW TYPE FUSE ONLY
NO
CONNECTION
ZONE 2ZONE 1
CONTROL
SWITCH
CONTROL
SWITCH
OUTPUT
TERMINALS
24VDC
OUTPUT
TERMINALS
24VDC
(+) (+) (+) (+)
(-) (-)
(IN) (IN)
(AD100 220V Version Optional)
Specific project or custom wiring diagrams available on re-
quest, consult the techinical service department.DORMA
NOTE: Always disconnect power prior to making any
connections or service.
It is recommended that the 120VAC power be supplied
from an Uninterrupted Power Supply (UPS) to ensure
proper operation during a power failure.
Always observe proper static discharge grounding pro-
cedure's when installing or servicing the DE device.
Wires that interconnect the remote authorized egress
and remote by-pass/rearm must be located within the
same room as the panic hardware (DE), or out-
side the door at no more than 10' feet of distance.
For ULC installations: "Authorities Having Juris- Some
diction" also require an illumination level of 100' feet at
the door, to be provided by the emergency power supply
system.
(12) Wire Connection
Bundle 22" in length.
DPS
(See Page 6 for typical
wiring of control inputs
and monitoring outputs.)
BLACK: (-) 24VDC IN
RED: (+) 24VDC IN
WHITE: AUTHORIZED EGRESS/AUTO RESET
ORANGE: BYPASS/RE-ARM
GREY: DPS N/C
VIOLET: ALARM RELAY COMMON
GREEN: RED OUTPUT EMITTER
BROWN: RED OUTPUT COLLECTOR
BLUE: GREEN OUTPUT EMITTER
YELLOW: GREEN OUTPUT COLLECTOR
PINK: ALARM RELAY N/C
TAN: ALARM RELAY N/O
Grey
Black

Product specificaties

Merk: Dormakaba
Categorie: Niet gecategoriseerd
Model: DE9000

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba DE9000 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Dormakaba

Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023
Dormakaba

Dormakaba RCI S2500A Handleiding

9 Juli 2023
Dormakaba

Dormakaba EAC Handleiding

9 Juli 2023
Dormakaba

Dormakaba CLM9000 Handleiding

9 Juli 2023
Dormakaba

Dormakaba DKX Type III Handleiding

9 Juli 2023
Dormakaba

Dormakaba 9800 Handleiding

9 Juli 2023
Dormakaba

Dormakaba HSW-GP Handleiding

9 Juli 2023
Dormakaba

Dormakaba DKX-10 Handleiding

9 Juli 2023
Dormakaba

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023
Dormakaba

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024