Dormakaba CL700 Handleiding

Dormakaba Niet gecategoriseerd CL700

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba CL700 (2 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 28 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/2

CL700 CYLINDRICAL LEVERSET

—

Installation Instructions

76002003 07/15www.dorma.com

Tools required for installation

#2 Cross drive screwdriver

1. Install latch

1.1 Place the latch into the door edge.

Orient such that the beveled edge of the latch

faces the door jamb.

1.2 Secure with two 8-32 x ¾ ” combo screws.

NOTE: Latch sleeve to be used for doors with

1-1/8” face plate prep and 1” latch bore.

2. Install lock assembly

Adjust for door thickness

NOTE: Lock comes adjusted for 1-¾ ”

door from the factory.

2.1 To adjust the lock assembly for

door thickness, align so the center

of the chassis is in line with the

center of the latch.

3. Install inside rose mounting plate

3.1 Hold the lock

assembly in place.

3.2 Thread the inside

rose mounting

plate onto the

chassis until snug

against the door

and tighten using

the included

spanner wrench.

Be sure holes in

plate are aligned

with the holes in

the door.

3.3 Secure the

mounting plate

using two

10-32 x 1-½ ”

screws.

2.2 Slightly separate the thru-bolt

retainer from the outside rose.

2.3 Rotate the outside rose assembly

to adjust for proper door thickness.

2.4 Realign the thru-bolt retainer with

the outside rose.

Install chassis

2.5 Slide the lock assembly into the face of the

door.

Be sure to engage the inner latch mechanism

of the chassis with the back of the latch as

432

Center of

latch

Chassis

Latch

Overall Exploded View

own

4. Install rose

4.1 Push the inside rose

onto the inside rose

mounting plate

oriented such that the

rose notch is

facing downward.

NOTE: Be sure the lever

insert is inserted into

the inside lever prior to

installation.

4.2 Push the inside lever

onto the spindle until

it clicks into place.

Part List

1 - IC core

2 - Outside IC lever

3 - Conventional cylinder

4 - Inside conventional

cylinder lever

5 - Lock assembly

6 - Inside rose mounting plate

7 - 10-32 x 1-½ ” screws (x2)

8 - Inside rose

9 - Lever insert

10 - Inside lever

11 - 8-32 x ¾ ” combo screws (2)

12 - Latch

13 - Latch sleeve

14 - Outside rose assembly

Beveled

edge

Spanner

wrench

Inside rose

mounting

plate

facin

g d

own

war

Chassis

Outside rose

assembly

Thru-bolt

retainer

Inside

lever

Inside

rose

Spindle

Inside

rose

mounting

plate

Rose

notch

location

5. Install strike

5.1 Insert strike as shown, and secure with two

12-24 x 1” combo screws.

Strike part list

1 - Strike plate

2 - 12-24 x 1” combo-screws

Supplementary Instructions

76002003 07/15 www.dorma.com

Removal

1. Remove the outside lever by inserting

the key, turn clockwise and at 45°. hold

Using the pick, depress the lever catch

through the pick hole and remove the

lever. Remove the key. (Figure 1a & 1b)

2. Remove the lever insert and cylinder.

Reinstallation

3. Replace with new cylinder and lever

insert, and reinstall the lever insert.

(Figure 2)

Be sure the tailpiece is horizontal.

4. Press the outside lever onto the

spindle until it contacts the lever catch

(Figure 3)

5. Insert the key into the cylinder, turn

clockwise and hold at 45°. Press the

lever fully onto the spindle until

it clicks into place. Release the

key. (Figure 3)

II. Removing & reassembling interchangeable core lever

III. Removing & reassembling standard cylinder lever (cylinder changes)

Removal

1. Insert the control key into the IC core,

rotate the key 15° clockwise, and remove

the core and tail piece from the lever.

2. Using a ﬂ athead screwdriver, retract the

lever catch inside the spindle and remove

the lever.

Reinstallation

3. Press the lever onto the spindle until it

snaps into place.

4. Install the tail piece on the core.

Insert the control key into the core,

rotate the key 15° clockwise, push the

core fully into the lever and turn counter

clockwise 15 ° (home position), and

remove the key.

IV. C701 Dummy trim installation

1. Using the pick, depress the

lever catch through the pick

hole and remove the lever.

2. Remove the rose from the

dummy mounting plate.

3. Position the dummy

mounting plate on the door with

the lever catch facing towards

the door edge.

4. Secure to the door using four

8-32 x ¾ ” combo screws.

5. Push the rose onto the

mounting plate oriented with

the rose notch facing

downward.

6. Push the inside lever onto the

spindle until it clicks into

place.

Single dummy trim

core

IC core lever

Dummy

mounting

plate

Rose

notch

location

Lever

catch

Door

edge

Rose

I. C770 - Timing instructions

TIMING INSTRUCTIONS: Install lock on door. Remove outside

lever and cylinder (for Interchangeable Core locks, leave levers in

place and remove cores and tail pieces)

OUTSIDE OF DOOR:

Rotate key spindle fully counter-clockwise.

Install cylinder and lever.

(See steps 4 & 5 in section III.)

Key spindle

45° Figure 1a

Figure 1b

Figure 2

Pick hole

Cylinder

Lever

insert

Tailpiece

(horizontal)

Lever

catch

45° Figure 3

core

IC core lever

Lever catch

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	CL700

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba CL700 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024