Dormakaba Auditcon 52 Handleiding

Dormakaba Niet gecategoriseerd Auditcon 52

Lees hieronder de 📖 handleiding in het Nederlandse voor Dormakaba Auditcon 52 (4 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 194 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF

Pagina 1/4

LOCK MODES

A maximum of two users can exist in a lock. A lock can operate in either Single Mode or

Dual Custody Mode.

Note:

For a UL listed installation, only one user can be activated.

• Single Mode E

Single Mode defaults to having only a Manager User (User 1) in the lock. A second

user (User 2) can then be added by the Manager User (User 1). (See section on

Manager User Operations.)

In Single Mode only one valid user combination is required to open the lock - the Manager

User (User 1) combination or the User 2 combination.

Note:

Default lock status from the factory is Single Mode with an opening

combination of “502550” for the Manager User (User 1).

• Dual Custody Mode E E

Dual Custody Mode defaults to two users in the lock - User 1 and User 2.

Two user combinations are required to open the lock - the User 1 combination and the

User 2 combination.

Note:

Manager User Operations are not available in Dual Custody Mode.

LOCK OPERATING CONVENTIONS

• The power source for the Auditcon 2 Lock Series is PowerStar

TM Technology.

With this technology an internal generator is used to create all necessary power.

Important Note: The lock must be manually powered before each operation by

briskly turning the dial back and forth .

• To clear a combination or keystroke, press the key.

• If the bolt is not retracted within 4-6 seconds after a valid opening combination is

accepted, the lock will “relock”.

Please note the following operational differences based on the type of bolt you have

installed:

• Dead Bolt (Manual Locking) Technology: There is a “Home” position for the dial on

the lock that is directly related to the manual retraction or extension of the bolt. In the

“HOME” position, the lip of the dial will cover the red “open lock” indicator. The dial

must be positioned here on a lock “Open’’ operation before you can successfully open

the lock. The dial must be turned to the right (CW) to retract the bolt and unlock the

lock. The dial must be turned to the left (CCW) to extend the bolt and lock the lock. The

lock may not open if more than a 5 lb. force is applied to the end or side of the bolt.

• Slide Bolt (Auto Locking) Technology: Once a combination has been entered and

accepted, the lock bolt movement works in conjunction with the bolt works of the

container. When the bolt works are disengaged to open the container, the lock bolt will

slide into the “unlocked” or retracted position. Once the bolt works are extended to the

locked position, the lock bolt automatically slides into the “locked” position. The lock will

not open if force is applied to the end or side of the bolt.

AUDITCON® 2 SERIES

MODELS 52 & T52

OPERATING INSTRUCTIONS

Document Number 3056.025 Rev. A2 - 05/05

LOCK RESPONSES

• The lock is “powered” when simultaneous green

and red

flashes display with

a beep 8.

• Each keystroke generates a green flash

with a beep 8.

• The completion of a step within an operation is indicated by a green flash

with a

beep 8.

• The successful completion of an operation is indicated by simultaneous

green

and red

flashes.

• If a valid combination or combinations are entered to open the lock, the lock will

respond as follows to indicate that the lock is ready to open:

Dead Bolt - 1 slow green flash

Slide Bolt - Continuous green flashes

... for approx. 5 seconds

• An error is indicated by three red flashes with beeps.

• If the Battery Assist option is included on your lock and a 9 Volt Alkaline has been

installed for Battery Assist, the LEDs will continually flash throughout the duration of a

Time Delay or Open Window period. There is not a battery low indicator for Battery

Assist. If the feature is not functioning properly, check the battery.

TO UNLOCK

1. For a Dead Bolt, place the dial in the Home position.

2. • For Single Mode

E (Factory combination is “502550”.)

Enter Manager User (User 1) or User 2 combination.

88888

• For Dual Custody Mode

E EE

Enter User 1 or User 2 combination.

888

Enter the second combination.

888

Wrong Try Penalty: 5 wrong tries = 3 min. lockout

Each additional wrong try = 3 min. lockout

Red flashes with beeps

888 will occur during the lockout while lock is powered.

3. For a Dead Bolt, dial right (clockwise) until the lock bolt is retracted. For a Slide

Bolt, rotate the container handle to unlock.

CHANGE COMBINATION

Caution:

When selecting a combination, do not use a birthday or other predictable data that

could give a correlation between the user and the combination.

Before changing a combina-

tion, open the container door to allow testing with the new combination.

1.• For User 1 (Manager User in Single Mode)

Press # and then 1.

• For User 2 (Must be added by Manager User in Single Mode)

Press #, # 1 and then .

2. Enter current combination. (Factory combination is “502550”.)

888

3. Enter new six-digit combination.

888

4. Enter new combination again for verification.

5. Open the lock with the new combination before closing container.

6. Record new combination and store it in a secure place.

CHANGE LOCK MODE (SINGLE / DUAL CUSTODY)

Note:

Changing the lock mode will reset the combination(s) to “502550”.

1.Press # 2 and then .

888

2. • If changing from Single to Dual Custody Mode

Enter Manager User (User 1) combination.

• If changing from Dual Custody to Single Mode

Enter User 1 or User 2 combination.

888

Enter the second combination.

SET TIME DELAY AND DELAYED OPENING WINDOW (Model T52 only)

1.Press # 5 and then .

888

2. • For Single Mode EE

E (Factory combination is “502550”.)

Enter Manager User (User 1) combination.

888

• For Dual Custody Mode EE

EEE EE

EEE

Enter User 1 or User 2 combination.

Enter the second combination.

3. Enter number of minutes (01-99) you want to delay lock opening or “00” to disable

time delay.

888

4. Enter the desired time delay again for verification.

888

If not “00”, proceed to step 6.

5. Enter number of minutes (01-20) for the delayed opening window.

888

6. Enter number of minutes for the delayed opening window again for verification.

Note:

A change in delayed opening will not take effect until after the next

opening of the lock.

TO UNLOCK WITH TIME DELAY SET (Model T52 only)

If operating a Model T52 Lock with Time Delay set to something other than 0, red flashes

will display after a combination has been entered and will continue during the delay

while the lock is powered.

Note:

If you have a Time Delay Display unit installed, the display unit will count down to

the end of the time delay period and will count up to the end of the window period.

When the delay time expires, you must power the lock.

Green flashes

display with beeps 8 to indicate the opening window is active

and will continue during the window while the lock is powered.

For a Dead Bolt, place the dial in the Home position.

Enter the combination(s) to open the lock.

BATTERY MAINTENANCE

To replace a battery on a battery assist lock, enter a valid combination to unlock the lock

and then open the container door. Locate the battery clip mounted inside the door near

the lock and replace the battery with a fresh 9 Volt Alkaline battery.

Product specificaties

Merk:	Dormakaba
Categorie:	Niet gecategoriseerd
Model:	Auditcon 52

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba Auditcon 52 stel dan hieronder een vraag en andere gebruikers zullen je antwoorden

Uw naam*

Jouw email*

Schrijf hier uw vraag

Handleiding Niet gecategoriseerd Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023

Dormakaba RCI S2500A Handleiding

9 Juli 2023

Dormakaba EAC Handleiding

9 Juli 2023

Dormakaba CLM9000 Handleiding

9 Juli 2023

Dormakaba DKX Type III Handleiding

9 Juli 2023

Dormakaba 9800 Handleiding

9 Juli 2023

Dormakaba HSW-GP Handleiding

9 Juli 2023

Dormakaba DKX-10 Handleiding

9 Juli 2023

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024

Kramer K-Bar Camera Bracket Handleiding

26 November 2024

Kramer RK-19 Handleiding

26 November 2024

Kramer OSP-MM1 Handleiding

26 November 2024

Kramer ASPEN-1616UX Handleiding

26 November 2024

Korg Pitchstrap Handleiding

26 November 2024

NeoMounts WL70-450BL11 Handleiding

26 November 2024

Kramer CLS-AOCH/60 Handleiding

26 November 2024

Klauke EKM 6022ISM Handleiding

26 November 2024