Dormakaba 7471K Handleiding

Dormakaba Niet gecategoriseerd 7471K

Lees hieronder de πŸ“– handleiding in het Nederlandse voor Dormakaba 7471K (9 pagina's) in de categorie Niet gecategoriseerd. Deze handleiding was nuttig voor 25 personen en werd door 2 gebruikers gemiddeld met 4.5 sterren beoordeeld

Download PDF
Pagina 1/9
MUNDUS PT21, PT24, PT25
Top Pivots
Installation instructions
838001 – 10-2017
| | EN
2MUNUDS Pivots 10-2017838001
dormakaba MUNDUS PT21, PT24, PT25 Installation Instructions Table of Contents
Table of contents
ξ˜‚ξ˜ƒ Technical specifications ξ˜„
1.1 Overview 3
1.1.1 General information 3
1.1.2 Intended use 3
1.1.3 Glass requirements/fittings/mounting 3
1.1.4 Requirements for glass panel 3
1.1.5 Safety instructions 3
1.1.6 Symbols used - Safety/Installation 3
1.1.7 Maintenance, care, repair 3
1.1.8 Disposal 3
1.2 Door dimensions 4
ξ˜… PTξ˜…ξ˜‚ Installation instructions ξ˜†
2.1 Dimensions 5
2.2 Secure PT21 pivot 5
2.3 Adjust PT21 6
ξ˜„ PTξ˜…ξ˜‡ Installation instructions 
3.1 Dimensions 7
3.2 Secure PT24 pivot 7
ξ˜‡ PTξ˜…ξ˜† Installation instructions ξ˜‰
4.1 Dimensions 8
4.2 Secure PT25 pivot 8
dormakaba MUNDUS PT21, PT24, PT25 Installation Instructions
838001 10-2017MUNUDS Pivots 3
Technical specifications
ξ˜‚ξ˜ƒ Technical specifications
ξ˜‚.ξ˜‚ Overview
These instructions are for installation of the PT21M,
PT24M and PT25M Top Pivots for the following
mounting and style versions:
ξ˜‚. Glass mounting
1.1.1 General information
β€’ dormakaba requires use of tempered laminated or
tempered monolithic glass.
β€’ dormakaba glass hardware is not suitable for harsh
environment; for example, applications where
chemicals (e.g. chlorine) are used such as indoor
swimming pools, saunas, or salt-water pools.
β€’ Do not swing doors with excessive force. Install
limiting stop to prevent door from opening too far.
1.1.2 Intended use
β€’ For pivoting doors in indoor or covered areas only.
β€’ For use with MUNDUS Patch Fittings only.
β€’ For manual slowly opening and closing only.
1.1.3 Glass requirements/fittings/mounting
β€’ The substructure/wall must be able to bear
permanent loads, be level (max. tolerance: 1/16”
[2] per 39” [1m]).
β€’ Fasteners must be sufficiently dimensioned for the
substructure/wall and weight of the door.
β€’ When adjusting glass elements, always stick to the
required clearance for the respective hardware.
Adjust clearance so glass does not come in contact
with any hard surfaces such as glass, metal or
concrete.
β€’ Do not use excessive force when installing the glass
(avoid over tightening screws.)
1.1.4 Requirements for glass panel
β€’ Heat-soaked thermally tempered safety glass
β€’ Clamping area must be flat and uncoated (no
self-cleaning coating!)
β€’ Never use glass with conchoidal fractures and/or
damaged edges.
1.1.5 Safety instructions
β€’ Installation requires two people.
β€’ Always wear protective clothing.
β€’ Only properly qualified and specially trained staff
are authorized to mount dormakaba glass
hardware.
β€’ Due to crushing hazards and possible injury caused
by breakage of glass during mounting,
corresponding protective clothing (especially gloves
and protective goggles) is required.
β€’ Never clamp metal fitting hardware directly to
glass surface.
β€’ Never use clamping products on surfaces with
self-cleaning coatings.
1.1.6 Symbols used - Safety/Installation
CAUTION
Mounting components must meet the
requirements of substructure/wall and door
weight. Please read the technical information
for fittings.
WARNING
Risk of breaking glass. When installing the
door, support the door panel with a block of
wood or similar object.
TIPS AND RECOMMENDATIONS
Information note
CLOSING EDGE OF DOOR
1.1.7 Maintenance, care, repair
β€’ Immediately replace damaged parts.
β€’ Always use original dormakaba parts.
β€’ Clean clamping area with alcohol-based standard
commercial cleaning agent before mounting the
glass hardware.
β€’ Use a damp cloth for occasional cleaning.
β€’ Always use silicone - and oil-free cleaners (e.g.
acetone).
β€’ Check glass hardware at regular intervals for
proper positioning, smooth operation and correct
adjustment.
β€’ High traffic door systems require inspection by
properly qualified staff (specialized companies or
installation firms.)
β€’ Function of fittings is recommended to be
inspected every 500,000 movements by a specialist.
1.1.8 Disposal
Disposal in accordance with local, state and national
regulations.

Product specificaties

Merk: Dormakaba
Categorie: Niet gecategoriseerd
Model: 7471K

Heb je hulp nodig?

Als je hulp nodig hebt met Dormakaba 7471K stel dan hieronder een vraag en andere gebruikers zullen je antwoorden


Handleiding Niet gecategoriseerd Dormakaba

Dormakaba

Dormakaba Keyscan EC1500 Handleiding

9 Juli 2023
Dormakaba

Dormakaba RCI S2500A Handleiding

9 Juli 2023
Dormakaba

Dormakaba EAC Handleiding

9 Juli 2023
Dormakaba

Dormakaba CLM9000 Handleiding

9 Juli 2023
Dormakaba

Dormakaba DKX Type III Handleiding

9 Juli 2023
Dormakaba

Dormakaba 9800 Handleiding

9 Juli 2023
Dormakaba

Dormakaba HSW-GP Handleiding

9 Juli 2023
Dormakaba

Dormakaba DKX-10 Handleiding

9 Juli 2023
Dormakaba

Dormakaba Confidant RFID Kit 1 Handleiding

9 Juli 2023
Dormakaba

Dormakaba DKX Type IV Handleiding

9 Juli 2023

Handleiding Niet gecategoriseerd

Nieuwste handleidingen voor Niet gecategoriseerd

Taga Harmony

Taga Harmony TOS-600 v.2 Handleiding

26 November 2024
Trace Elliot

Trace Elliot Pro 2x12 Cabinet Handleiding

26 November 2024
Kramer

Kramer K-Bar Camera Bracket Handleiding

26 November 2024
Kramer

Kramer RK-19 Handleiding

26 November 2024
Kramer

Kramer OSP-MM1 Handleiding

26 November 2024
Kramer

Kramer ASPEN-1616UX Handleiding

26 November 2024
Korg

Korg Pitchstrap Handleiding

26 November 2024
NeoMounts

NeoMounts WL70-450BL11 Handleiding

26 November 2024
Kramer

Kramer CLS-AOCH/60 Handleiding

26 November 2024
Klauke

Klauke EKM 6022ISM Handleiding

26 November 2024